Examkin

Ignition System

25 soru

Tüm türler25Çoktan seçmeli12Eşleştirme7Sıralama6
Soru 21Soru →

A technician is tracing the pathway of electrical energy in a conventional distributor-based ignition system. In what chronological sequence does electrical energy travel from the low-voltage source to ignite the cylinder's air-fuel mixture?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct chronological sequence is: (1) 12-volt battery current flows through the primary winding to build a magnetic field, (2) The primary circuit switch opens to collapse the magnetic field, (3) High voltage is induced in the secondary winding and travels to the distributor cap, and (4) The distributor rotor directs the high voltage across the spark plug wire to fire the spark plug.
In a conventional distributor ignition system, low-voltage current from the battery first energizes the primary coil windings to build a magnetic field. When the switching mechanism opens, the current stops and the magnetic field collapses instantly. This rapid collapse induces tens of thousands of volts in the secondary coil windings. The high-voltage surge enters the distributor cap, where the rotating rotor directs it to the correct spark plug wire, jumping the spark plug gap to ignite the compressed air-fuel mixture.

Adım Adım Çözüm

1
Identify the primary circuit energizing stage.
Low-voltage current from the battery flows through the primary coil winding, creating a strong magnetic field around the iron core.
An ignition coil must store electrical energy in a magnetic field before it can be stepped up to firing voltage.
2
Identify the triggering event that releases stored magnetic energy.
The contact points or switching transistor opens the circuit, abruptly interrupting primary current flow.
High-voltage induction requires a rapid rate of change in the magnetic lines of force.
3
Trace the step-up voltage transformation in the secondary circuit.
The collapsing magnetic lines cut through the secondary winding, inducing a surge of 20,000 to 50,000 volts that exits through the coil tower.
The high ratio of secondary turns to primary turns steps up the collapsing field energy into high voltage.
4
Trace the mechanical distribution to the combustion chamber.
The distributor rotor turns toward the cylinder's cap terminal, routing the surge through the plug wire to spark across the electrode gap.
The distributor mechanically times and directs the high voltage to the cylinder ready for combustion.

Anahtar Kavram

Ignition coil primary magnetic saturation, field collapse induction, and high-voltage distributor delivery
Tahmini Süre:1m 0s
Soru 22Soru →

Match each automotive ignition system component with its primary operating function.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Öğeler

Centrifugal advance mechanism
Ballast resistor
Ignition pickup coil
Spark plug ceramic insulator

Eşleşmeler

Cevabı ve açıklamayı göster

Cevap

Centrifugal advance mechanism matches with using spring-loaded flyweights to advance spark timing with engine speed; Ballast resistor matches with reducing primary circuit operating voltage to protect the coil; Ignition pickup coil matches with generating an alternating electrical pulse to trigger the spark; Spark plug ceramic insulator matches with preventing high-voltage current from shorting to the cylinder head.
Each pair correctly matches an essential ignition sub-component with its physical and electrical task. The centrifugal advance mechanism uses spinning flyweights to advance timing at higher engine speeds; the ballast resistor limits current to protect the primary coil windings; the pickup coil generates timing pulses to control switching; and the ceramic insulator contains secondary high voltage to ensure an arc across the spark plug electrode gap.

Adım Adım Çözüm

1
Analyze the mechanical timing mechanism
Identified that the centrifugal advance mechanism utilizes flyweights and counteracting springs inside the distributor to rotate the cam assembly forward as crankshaft RPM increases.
At higher engine speeds, combustion needs more lead time relative to piston travel, requiring mechanical timing advance.
2
Analyze the primary circuit electrical protection component
Identified that the ballast resistor provides electrical resistance in series with the primary coil windings once the starter motor disengages.
Full battery voltage is provided only during cranking; during running, the resistor limits coil saturation current to prevent burnout.
3
Analyze the electronic trigger sensor
Identified that the ignition pickup coil operates as a variable reluctance sensor creating voltage spikes as reluctor teeth pass.
The ignition control module requires these precise electronic pulses to switch primary current off and collapse the magnetic field.
4
Analyze the spark plug structural insulation
Identified that the high-dielectric ceramic insulator encapsulates the center electrode to contain tens of thousands of volts.
Secondary current takes the path of least resistance; the insulator ensures current discharges exclusively across the air gap rather than shorting to the cylinder head.

Anahtar Kavram

Operating roles and electrical/mechanical principles of specialized components across primary and secondary ignition circuits
Tahmini Süre:1m 0s
Soru 23Soru →

In a four-stroke internal combustion gasoline engine, the ignition system must deliver high-voltage current to ignite the air-fuel mixture at the optimal moment. Under normal operating conditions, at which point in the engine operating cycle does the spark plug fire?

Cevabı ve açıklamayı göster

Cevap: Slightly before top dead center near the end of the compression stroke

Cevap

Slightly before top dead center near the end of the compression stroke
In a gasoline engine, ignition timing is set to fire the spark plug several degrees before top dead center (BTDC) near the end of the compression stroke. Because the air-fuel mixture requires a brief moment to burn and expand, initiating the spark just before the piston reaches the top of its compression travel ensures that maximum cylinder pressure pushes down on the piston at the start of the power stroke.

Adım Adım Çözüm

1
Identify the purpose of the ignition spark in a four-stroke internal combustion cycle.
The spark must ignite the tightly compressed air-fuel charge to create high pressure that drives the piston downward.
Maximum thermal and mechanical efficiency requires peak cylinder pressure to occur just after the piston begins descending on the power stroke.
2
Account for flame propagation time.
Combustion is not instantaneous; the flame front takes several milliseconds to spread across the combustion chamber.
To achieve peak combustion pressure at the beginning of the power stroke, the ignition event must be initiated slightly before the piston reaches Top Dead Center (TDC) on the compression stroke.

Anahtar Kavram

Ignition Timing and Four-Stroke Cycle Synchronization
Tahmini Süre:1m 0s
Soru 24Soru →

Modern vehicles utilize electronic control units to precisely orchestrate spark generation at each cylinder. Arrange the operational phases of a coil-on-plug (COP) firing cycle in the correct chronological order from initial sensor input to spark delivery.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct chronological sequence is: (1) Position sensor signal transmission to the engine control module, (2) Primary circuit dwell to build the magnetic field, (3) Primary circuit interruption causing magnetic field collapse, and (4) Secondary winding high-voltage induction and spark gap discharge.
An electronic ignition cycle begins when position sensors inform the engine computer of crankshaft angle and cylinder position. The computer activates the coil's primary circuit driver to establish a strong magnetic field (dwell). When ignition is commanded, the driver opens the primary circuit; the resulting instantaneous magnetic collapse cuts across thousands of secondary winding turns, stepping battery voltage up to tens of thousands of volts, which jumps the spark plug gap.

Adım Adım Çözüm

1
Identify the initiating timing input
Crankshaft and camshaft position sensor pulses provide the engine control module with precise piston position data.
The computer cannot calculate dwell timing or advance without rotational reference signals.
2
Trace the energy storage phase in the ignition coil
Current flows through the primary winding during the dwell period, saturating the magnetic core.
Magnetic flux must be fully established in the primary winding before a secondary pulse can be generated.
3
Identify the switching trigger that releases stored energy
The primary circuit ground is opened, causing instantaneous collapse of the magnetic field.
Faraday's law of induction dictates that voltage magnitude depends directly on the speed of magnetic field collapse across the windings.
4
Trace the final delivery of stepped-up secondary voltage
The thousands of secondary turns produce 20,000 to 50,000 volts, ionizing the plug gap and jumping across the electrodes.
The extreme step-up ratio overcomes the high electrical resistance of dense, compressed cylinder gases to ignite the mixture.

Anahtar Kavram

Electronic Ignition Primary-to-Secondary Transformation and Timing Sequence
Tahmini Süre:1m 0s
Soru 25Soru →

An automotive ignition system relies on distinct mechanical, electrical, and solid-state devices working together to generate and distribute high-voltage spark. Match each ignition system component with its correct operational function.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Öğeler

Ignition Control Module (ICM)
Crankshaft Position (CKP) Sensor
Distributor Rotor
Spark Plug Ground Electrode

Eşleşmeler

Cevabı ve açıklamayı göster

Cevap

Ignition Control Module pairs with switching the primary coil circuit; Crankshaft Position Sensor pairs with monitoring rotational speed and position; Distributor Rotor pairs with mechanically directing secondary voltage; Spark Plug Ground Electrode pairs with providing the grounded terminal for the spark arc.
Each pair correctly matches an ignition system part with its core operational principle: the Ignition Control Module switches the primary coil ground to induce high voltage, the Crankshaft Position Sensor feeds critical rotational angle data to the control computer, the Distributor Rotor physically channels high-voltage pulses according to cylinder firing order, and the Spark Plug Ground Electrode provides the stationary terminal that forms the spark gap.

Adım Adım Çözüm

1
Analyze the primary circuit switching component.
Identify the Ignition Control Module as the solid-state transistor switch that opens and closes the primary winding ground circuit to trigger induction.
Inducing high secondary voltage in the ignition coil requires rapidly collapsing the primary magnetic field.
2
Analyze the engine timing input sensor.
Identify the Crankshaft Position Sensor as the magnetic or Hall-effect pickup that supplies rotational speed and piston position reference data.
The electronic control module requires crankshaft data to determine the exact moment to fire each cylinder.
3
Analyze the high-voltage mechanical distribution element.
Identify the Distributor Rotor as the rotating contact that transfers secondary voltage from the coil center post to the outer cylinder cap terminals.
Conventional distributor systems use a synchronized rotating contact to route spark energy according to the engine firing order.
4
Analyze the combustion chamber spark termination component.
Identify the Spark Plug Ground Electrode as the grounded physical projection that establishes the spark gap alongside the center electrode.
The secondary circuit must complete a path to engine ground to produce the electric arc that ignites the fuel charge.

Anahtar Kavram

Ignition System Component Functions and Operating Roles
Tahmini Süre:1m 15s
ÖncekiSayfa 2 / 2
Ignition System Alıştırma Soruları — Armed Services Vocational Aptitude Battery (ASVAB) — Sayfa 2 | Examkin