Hand Tools

125 soru

Tüm türler125 Çoktan seçmeli62 Doğru / Yanlış14 Sayısal2 Eşleştirme30 Sıralama17

A technician fabricating an aluminum instrument bracket needs to create a clean, deburred 1/2-inch hole through 18-gauge sheet metal without distorting the workpiece or having the cutting edges snag upon breakthrough. Which drilling tool is specifically designed with graduated, tiered cutting diameters along a single conical body to perform this task?

Brad-point bit

Step drill bit

Spade bit

Auger bit

Cevabı ve açıklamayı göster

Cevap: Step drill bit

Cevap

The step drill bit is the correct tool for boring clean, controlled holes in thin sheet metal without binding.

The step drill bit features a conical profile with progressively larger cutting steps along its length. This stepped architecture allows each tier to act as a pilot for the next diameter, preventing the cutting edge from grabbing or tearing thin metal panels and automatically deburring the hole edges.

Adım Adım Çözüm

Analyze the material thickness and cutting characteristics of the workpiece

Identified 18-gauge sheet metal, which is thin and prone to grabbing, chatter, and distortion when cut with standard flutes.

Thin materials lack the axial depth needed to guide conventional drill margins, often resulting in tearing when cutting lips break through the underside.

Evaluate the geometric design of hole-making tools across the options

The step drill bit features a tapered series of distinct cylindrical steps that increase progressively in diameter.

Each step cuts a shallow radial ledge and deburrs the previous step, eliminating breakthrough binding and creating smooth, round holes in sheet materials.

Anahtar Kavram

Application and geometry of step drill bits for thin-gauge metal fabrication

Tahmini Süre:1m 0s

Soru 122Soru →

When boring a clean through-hole in a piece of timber using a hand brace and an auger bit to prevent wood tear-out (blowout) on the exit side, in what sequence should the procedure be performed?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

Mark the hole center location, bore from the front face until the lead screw point just pierces through the rear surface, withdraw the bit and reverse the workpiece, and complete boring from the rear face.

Standard shop practice when boring through timber with an auger bit requires laying out the mark first, boring from the front until only the lead screw tip breaks through, and then reversing the workpiece to finish the cut from the back side inward. This prevents the cutting spurs from tearing out unsupported grain on exit.

Adım Adım Çözüm

Establish and mark the hole center on the entry face of the timber.

The exact starting point for the auger bit lead screw is identified.

Accurate layout prevents wandering and ensures proper hole alignment before cutting begins.

Bore straight into the front face until only the tip of the feed screw pokes through the exit side.

The majority of the waste is removed while the rear grain remains intact.

Halting the cut before the cutting lips and spurs breach the back face prevents splintering and blowout.

Back the auger bit out of the workpiece and access the rear face.

The small pilot prick mark made by the screw point is clearly visible on the reverse side.

Accessing the rear face allows the cutting spurs to enter supported wood rather than exiting unsupported fibers.

Insert the feed screw into the pilot hole on the rear face and finish boring inward.

The center plug is freed, leaving a clean, tear-out-free through-hole.

Cutting inward from both outer faces ensures that all wood fibers are sheared cleanly toward the inside of the workpiece.

Anahtar Kavram

Preventing exit tear-out during manual auger bit boring by cutting inward from opposite faces.

Tahmini Süre:1m 0s

Soru 123Soru →

During a routine alternator replacement, an automotive technician must tighten a hex-head mounting bolt that measures $15\text{ mm}$ across the flats. The technician cannot locate the $15\text{ mm}$ wrench and considers substituting a standard fractional $5/8\text{ in}$ wrench from an SAE tool set. Which of the following describes the most likely outcome of using this fractional wrench?

The wrench opening will be significantly undersized at approximately

14.29\text{ mm}

, preventing it from slipping over the bolt head.

The wrench opening will be oversized at approximately

15.88\text{ mm}

, causing a loose fit that can slip and round off the bolt corners.

The wrench will provide an exact dimensional match because

5/8\text{ in}

converts precisely to

15.00\text{ mm}

in standard automotive fastener sizing.

The wrench will bind against the fastener corners with severe interference, causing the box-end opening to crack or stretch.

Cevabı ve açıklamayı göster

Cevap: The wrench opening will be oversized at approximately $15.88\text{ mm}$ , causing a loose fit that can slip and round off the bolt corners.

Cevap

The wrench opening will be oversized at approximately

15.88\text{ mm}

, causing a loose fit that can slip and round off the bolt corners.

Converting

5/8\text{ in}

to metric yields

0.625 \times 25.4 = 15.875\text{ mm}

. Because

15.875\text{ mm}

is noticeably larger than the

15\text{ mm}

bolt head, the wrench fits loosely with

0.875\text{ mm}

of play. Applying tightening torque with this loose fit causes the wrench jaws to ride over the fastener vertices, rounding off the hex head.

Adım Adım Çözüm

Convert the fractional SAE wrench size (

5/8\text{ in}

) to decimal inches.

5 \div 8 = 0.625\text{ in}

Converting to decimal form simplifies conversion to metric units.

Convert decimal inches to millimeters using the standard conversion factor (

1\text{ in} = 25.4\text{ mm}

0.625\text{ in} \times 25.4\text{ mm/in} = 15.875\text{ mm}

Determining the metric equivalent allows direct comparison to the

15\text{ mm}

fastener head.

Calculate the clearance gap between the wrench jaw opening and the fastener head.

15.875\text{ mm} - 15.000\text{ mm} = 0.875\text{ mm}

(approximately

0.034\text{ in}

)

Clearance determines whether the tool makes solid flat contact or slips onto the corners.

Evaluate the mechanical consequences of excessive clearance under torque.

The oversized wrench contacts only the extreme tips of the hex vertices rather than the flats, causing slippage and corner rounding.

Proper torque transfer requires tight engagement across fastener flats.

Anahtar Kavram

Metric and SAE Wrench Incompatibility and Fastener Corner Rounding

Alternatif Yöntem

Memorizing key baseline equivalents (

1/2\text{ in} \approx 12.7\text{ mm}

9/16\text{ in} \approx 14.3\text{ mm}

5/8\text{ in} \approx 15.9\text{ mm}

) allows rapid estimation of SAE-to-metric clearances without manual division.

Tahmini Süre:1m 0s

Soru 124Soru →

A technician is preparing to torque critical automotive fasteners to manufacturer specifications using a click-type micrometer torque wrench. What is the correct chronological sequence of steps to properly set up, operate, and store the tool?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct procedural order is: (1) Locate the torque specification in the service manual, (2) Disengage the handle lock and adjust the micrometer scale, (3) Re-engage the locking collar, (4) Apply steady pulling force until the click occurs, and (5) Wind the handle back down to the lowest setting for storage.

The procedure begins by referencing the manufacturer torque specifications in the service manual. Next, the tool's lock mechanism must be opened to allow the micrometer handle to be dialed to the target value. The lock must then be re-engaged to prevent handle rotation during use. Torque is applied smoothly in a pulling motion until the tool clicks, at which point force must cease immediately. Finally, the tool's internal spring tension must be relieved down to the lowest graduated mark before storing to maintain calibration accuracy.

Adım Adım Çözüm

Consult technical data to establish the target torque value.

The target torque specification (e.g., in foot-pounds or Newton-meters) is known.

Accurate torque application requires using the manufacturer's exact specified torque rating.

Unlock the handle collar and adjust the calibrated micrometer sleeve to the specified reading.

The internal calibrated spring is compressed to the target load.

The micrometer scale must be precisely aligned while the locking ring is disengaged.

Lock the micrometer handle in place.

The scale setting is secured against rotation during tool handling.

Hand pressure during operation can inadvertently twist an unlocked grip, altering the applied torque.

Position the wrench perpendicular to the fastener and pull smoothly until the mechanism clicks once.

Fastener reaches exact specified clamping force.

The click indicates that the pre-set torque threshold is met; continuing to pull beyond the click over-torques the fastener.

Zero out spring tension by adjusting the micrometer handle down to its lowest setting prior to storage.

The internal spring rests in an uncompressed state.

Leaving a torque wrench stored under tension causes spring fatigue and ruins measurement calibration.

Anahtar Kavram

Click-Type Torque Wrench Operation and Maintenance Sequence

Tahmini Süre:1m 15s

Soru 125Soru →

A mechanic is organizing a shop toolkit for specialized mechanical and automotive repair tasks. Match each wrench type to its primary operational function.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Flare-nut wrench matches soft metal line fittings; Pin spanner wrench matches circular retaining collars; Basin wrench matches fasteners in deep vertical cavities; Striking wrench matches sledgehammer-driven heavy fasteners.

Each wrench profile is built for specific fastener geometries and working environments: flare-nut wrenches wrap five flats of soft tubing fittings, pin spanners interface with notched round collars, basin wrenches access narrow vertical recesses beneath fixtures, and striking wrenches withstand sledgehammer impacts on frozen heavy-machinery hardware.

Adım Adım Çözüm

Identify the wrench engineered for fluid lines with soft metal fittings.

Flare-nut (tubing) wrench connects to the soft metal brake and fuel lines description.

Standard open-end wrenches contact only two flats and slip easily under high torque, whereas flare-nut wrenches enclose five flats.

Identify the wrench engineered for round retaining collars and slotted locknuts.

Pin spanner wrench connects to the radial pin holes and slots description.

Cylindrical fasteners lack standard hex flats and require a dedicated hook or pin to transfer rotational torque.

Identify the wrench engineered for vertical reach in tight, deep recesses.

Basin wrench connects to the deep, confined cavities behind fixtures description.

Its long shank and swiveling spring jaw allow single-handed operation in obstructed vertical enclosures.

Identify the wrench engineered for high-impact shock loading.

Striking (slugging) wrench connects to the sledgehammer-driven heavy equipment fastener description.

It features an extra-thick forged anvil block specifically designed to absorb hammer strikes without shattering.

Anahtar Kavram

Specialized Wrench Profiles and Mechanical Applications

Tahmini Süre:1m 15s

ÖncekiSayfa 7 / 7

Hand Tools

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Alternatif Yöntem

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar