Examkin

Electrical Hand Tools

15 soru

Tüm türler15Çoktan seçmeli7Eşleştirme3Sıralama5
Soru 1Soru →

An electrician is preparing to connect a solid copper conductor to a standard screw terminal. Arrange the following steps in the correct operational sequence using the proper electrical hand tools.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

1. Strip the conductor using a wire stripper. 2. Form a loop in the bare copper with needle-nose pliers. 3. Hook the wire clockwise around the screw post. 4. Tighten the terminal screw with a screwdriver.
The correct operational sequence begins by using wire strippers with the proper gauge notch to cleanly remove insulation without nicking the conductor. Needle-nose pliers are then used to bend the bare copper into a hook. The hook is placed clockwise around the screw post so that tightening rotation draws the wire inward. Finally, an appropriately sized screwdriver fastens the terminal screw securely.

Adım Adım Çözüm

1
Use the correctly sized gauge notch of a wire stripper to strip insulation from the conductor end.
Exposes undamaged, bare solid copper wire.
Proper notch selection prevents nicking, which can weaken the solid wire.
2
Grip the bare conductor end with needle-nose pliers and form a 3/4-circle loop.
Produces a clean hook sized to fit the terminal screw diameter.
Needle-nose pliers allow precise shaping without distorting or scarring the copper.
3
Position the hook around the terminal screw post facing clockwise.
The loop opening aligns with the clockwise tightening rotation of the screw.
Clockwise placement ensures rotational friction from the screw draws the wire tighter around the shank.
4
Drive the screw down firmly using a matching insulated screwdriver.
Creates a secure, low-resistance electrical connection.
Proper screwdriver sizing ensures adequate torque without camming out or damaging the screw head.

Anahtar Kavram

Standard hand-tool procedure for terminating solid conductors under screw terminals, including tool selection and clockwise loop orientation.
Tahmini Süre:1m 0s
Soru 2Soru →

An electronics technician is tasked with creating an insulated, moisture-resistant in-line crimp splice on a stranded copper wire using manual electrical hand tools. In what sequential order should the following steps be executed to ensure proper mechanical strength and electrical integrity?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence is: (1) Trim the damaged conductor ends square using diagonal cutting pliers, (2) Slide the heat-shrink tubing onto one lead away from the joint, (3) Strip the insulation using the matched wire stripper notch, (4) Insert the wire into the butt connector and compress with the ratcheting crimper, and (5) Center the tubing over the joint and shrink with a heat gun.
Executing the sequence by trimming, staging heat-shrink tubing, stripping with sized stripper notches, crimping with a calibrated ratcheting tool, and finally heat-sealing adheres strictly to standard electrical assembly protocols, ensuring both conductor integrity and permanent insulation.

Adım Adım Çözüm

1
Cut and square off the wire conductors using diagonal cutting pliers.
Clean, perpendicular wire ends ready for stripping and connector seating.
Jagged or frayed wire ends prevent uniform insertion into crimp barrels and can puncture insulation.
2
Place heat-shrink sleeving over one wire harness branch before completing the splice.
Protective sleeving is staged on the wire harness.
Closed-loop in-line splices cannot accommodate non-split heat-shrink tubing once the terminal barrel is crimped to both sides.
3
Strip the manufacturer-specified strip length using the exact AWG-marked die of precision wire strippers.
Exposed copper strands with zero severed, nicked, or displaced wire strands.
Using an oversized notch fails to strip cleanly, while an undersized notch severs outer strands and reduces current-carrying capacity.
4
Seat the stripped conductors into the butt connector barrel and cycle the ratcheting crimper until the mechanism releases.
A gas-tight, cold-welded mechanical and electrical connection with high tensile pull-out strength.
Ratcheting crimpers enforce full compression of the terminal barrel without under-crimping or over-fracturing the metal sleeve.
5
Position the heat-shrink tubing symmetrically over the metal barrel and apply hot air evenly.
A fully insulated, moisture-proof, strain-relieved wire connection.
Even heating prevents scorching the wire insulation while ensuring the internal hot-melt adhesive flows to seal out moisture.

Anahtar Kavram

Standard sequential operation of electrical hand tools for wire preparation, mechanical termination, and splice insulation.
Tahmini Süre:1m 30s
Soru 3Soru →

When trimming excess component leads on a printed circuit board after soldering through-hole parts, standard beveled cutting pliers pinch the wire and transmit mechanical shock into the solder joint, potentially fracturing the pad. Which specialized electrical hand tool features cutting edges that meet flat on the reverse side to produce a clean, flat cut without placing stress on the solder connection?

Cevabı ve açıklamayı göster

Cevap: Flush cutters

Cevap

Flush cutters
Flush cutters are engineered specifically for electronics fabrication with single-beveled or shear-action blades that are perfectly flat on the back side. When placed against a circuit board, they slice through copper component leads cleanly without the crushing action that transfers damaging kinetic shock into the solder fillet.

Adım Adım Çözüm

1
Analyze the mechanical requirements of the task
Identified the need to trim component leads close to a circuit board without transmitting cutting shock to fragile solder pads.
Standard double-bevel cutting edges squeeze metal inward from both sides before severing it, creating an axial shockwave along the lead into the joint.
2
Evaluate the jaw geometry of electrical cutting hand tools
Flush cutters feature a zero-bevel flat outer face that shears through copper leads with a slicing action rather than a pinching action.
The flat back of flush cutters rests parallel to the board surface and produces a smooth cut with minimal residual mechanical strain.
3
Select the appropriate hand tool for delicate electronics work
Flush cutters are the designated tool for post-soldering lead trimming on printed circuit boards.
Other pliers either possess heavy double-beveled jaws or are specialized for insulation removal rather than lead trimming.

Anahtar Kavram

Hand tool cutting blade geometry and application in electronics assembly
Tahmini Süre:1m 15s
Soru 4Soru →

An electrician needs to terminate a solid copper conductor onto a standard screw terminal. What is the correct sequence of steps to complete this operation using manual hand tools?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

Strip the insulation using wire strippers, bend the bare conductor into a clockwise loop using needle-nose pliers, place the loop clockwise around the screw shank, and tighten the screw securely with an insulated screwdriver.
The proper sequence begins by using wire strippers to expose bare conductor. Next, needle-nose pliers are used to bend the wire into a clockwise hook. The hook is then seated around the screw post in the direction of rotation, and finally, an insulated screwdriver tightens the screw to secure the termination.

Adım Adım Çözüm

1
Select the correct gauge notch on manual wire strippers and remove approximately 3/4 inch of insulation from the solid conductor.
The bare copper conductor is exposed cleanly without nicks or damage.
Insulation must be removed prior to shaping or establishing electrical contact.
2
Grip the tip of the exposed copper wire with needle-nose pliers and form a smooth, clockwise U-shaped bend.
A terminal loop sized to fit around the screw post is created.
Needle-nose pliers provide the leverage and precision required to form an exact loop.
3
Hook the wire loop clockwise around the screw post under the screw head.
The loop is positioned so that standard clockwise screw rotation pulls the wire tighter instead of pushing it out.
Orienting the loop in the tightening direction prevents the wire from spreading open.
4
Drive and tighten the screw firmly against the conductor using an appropriately sized insulated screwdriver.
A mechanically stable, low-resistance electrical connection is completed.
The screwdriver clamps the wire tightly between the screw head and the contact plate.

Anahtar Kavram

Standard operating procedure for preparing and terminating a conductor onto a screw terminal using hand tools.
Soru 5Soru →

During the maintenance of an electronic control board, a technician must remove a damaged resistor from a soldered through-hole terminal. After heating the connection with a soldering iron, which hand tool is specifically used to draw the liquefied solder away by creating a vacuum?

Cevabı ve açıklamayı göster

Cevap: Desoldering pump

Cevap

A desoldering pump is specifically used to vacuum liquefied solder away from a joint during component removal.
A desoldering pump (solder sucker) uses a spring-loaded piston to create sudden negative pressure (vacuum), which draws molten solder out of the terminal joint into the tool reservoir.

Adım Adım Çözüm

1
Identify the specific task required in the scenario.
The technician needs to clear molten solder from a printed circuit board terminal.
Removing a soldered through-hole component requires extracting the molten metal holding the lead in place.
2
Select the hand tool designed for vacuum extraction of liquid solder.
The desoldering pump (often called a solder sucker) creates suction when its spring mechanism is triggered.
The vacuum rapidly pulls the liquid solder into the tool's barrel before the solder cools and solidifies.

Anahtar Kavram

Identification and functional application of desoldering hand tools in electronics repair.
Tahmini Süre:45s
Soru 6Soru →

Match each electrical hand tool with its primary application in wiring and circuit assembly.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Öğeler

Lineworker pliers
Needle-nose pliers
Ratcheting crimper
Fish tape

Eşleşmeler

Cevabı ve açıklamayı göster

Cevap

Lineworker pliers match gripping and twisting heavy conductors; needle-nose pliers match holding small parts and forming wire loops; ratcheting crimpers match deforming solderless terminal sleeves; fish tape matches pulling conductors through conduit runs.
Each tool matches its designated electrical trade function: lineworker pliers provide heavy-duty gripping and twisting for solid conductors, needle-nose pliers allow precision handling and loop formation in confined areas, ratcheting crimpers apply calibrated pressure to secure solderless lugs, and fish tape provides the semi-rigid guide needed to draw conductors through conduit tubing.

Adım Adım Çözüm

1
Examine the mechanical design of each tool listed.
Identified heavy-duty gripping jaws, fine precision jaws, compression dies, and flexible pulling tape.
Each hand tool is specialized to perform a distinct physical task safely and effectively in electrical installation.
2
Pair each tool with the corresponding functional description.
All four tools correctly matched to their operational tasks.
Using the designated tool prevents wire damage, joint failure, and improper mechanical terminations.

Anahtar Kavram

Identification and standard functional applications of electrical hand tools
Tahmini Süre:45s
Soru 7Soru →

When servicing an industrial control cabinet, a technician must safely remove a cylindrical cartridge fuse from its spring mounting clips. Which hand tool is specifically manufactured from non-conductive insulating material to perform this task without creating an electrical shock hazard?

Cevabı ve açıklamayı göster

Cevap: Fuse puller

Cevap

Fuse puller
A fuse puller is manufactured from high-dielectric insulating materials such as vulcanized fiber or molded nylon, featuring specially contoured jaws that clamp securely onto cylindrical cartridge fuses without conducting electricity.

Adım Adım Çözüm

1
Identify the electrical safety requirement for removing cartridge fuses from mounting clips.
Cartridge fuses reside in spring tension clips that may remain energized; using metal hand tools creates a direct shock and phase-to-ground fault hazard.
Standard metal hand tools conduct electric current directly to the technician's hands.
2
Select the dedicated hand tool constructed from dielectric, non-conductive material.
A fuse puller provides mechanical leverage and notched jaws to firmly grip cylindrical fuses while insulating the operator completely from electrical potential.
Dedicated fuse pullers ensure compliance with safety protocols by preventing current flow through the user.

Anahtar Kavram

Non-conductive electrical hand tools (fuse pullers) protect technicians from shock and short circuits when installing or extracting cartridge fuses.
Tahmini Süre:35s
Soru 8Soru →

An electrician is joining two solid copper conductors to form a pigtail splice using standard electrical hand tools. What is the correct sequence of steps to complete this connection?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence is: Strip the insulation with wire strippers, align the bare ends with lineworker pliers, twist the conductors clockwise into a tight spiral, trim the twisted tips flush with the plier cutting blades, and thread a twist-on wire connector over the splice.
The correct procedure begins with stripping the outer insulation to expose clean copper. The bare ends are then aligned and twisted clockwise with lineworker pliers to establish a secure mechanical bond. Trimming any uneven ends ensures the splice fits fully inside the twist-on wire connector, which is screwed on last to provide electrical insulation.

Adım Adım Çözüm

1
Strip wire insulation
Clean bare copper conductors are exposed without nicking the metal.
Removing insulation is the mandatory first step to establish electrical conductivity.
2
Align and hold bare ends with lineworker pliers
The two conductors are positioned parallel in the plier jaws.
Even alignment ensures uniform tension and twisting across both wires.
3
Twist conductors clockwise
A tight, solid mechanical twist is formed.
Provides mechanical strength and prevents loose contacts under thermal cycling.
4
Trim the splice tip flush
The twisted conductors end at an equal length.
Prevents exposed bare copper from protruding past the connector housing.
5
Install the twist-on wire connector
The joint is mechanically locked and electrically insulated.
Encloses the bare connection to prevent short circuits and shock hazards.

Anahtar Kavram

Proper operational procedure for creating a mechanical pigtail wire splice using hand tools
Tahmini Süre:45s
Soru 9Soru →

An electrical technician is assembling conduit raceways, enclosure boxes, and data distribution hardware for a commercial installation. Match each specialized electrical hand tool to its primary function.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Öğeler

Fish tape
Punch-down tool
Conduit bender
Knockout punch

Eşleşmeler

Cevabı ve açıklamayı göster

Cevap

Fish tape matches pulling conductors through raceways; Punch-down tool matches terminating and trimming data conductors into IDC blocks; Conduit bender matches forming precise bends and offsets in electrical metallic tubing; Knockout punch matches cutting circular openings in sheet metal enclosures.
Each tool is matched to its intended electrical installation function: fish tape provides tensile pulling through conduit, punch-down tools execute IDC terminations for communications wiring, conduit benders impart specific angular curves to EMT, and knockout punches create precise circular knockouts in steel enclosures.

Adım Adım Çözüm

1
Determine the application of a fish tape.
Fish tape is designed for pulling wire conductors through rigid, IMC, or EMT conduit systems.
Its long, narrow, and flexible spring-steel construction allows it to navigate bends inside enclosed raceways.
2
Determine the application of a punch-down tool.
A punch-down tool is used to terminate structured cabling into punch-down blocks and patch panels.
It pushes the wire into an insulation-displacement contact, piercing the jacket to establish electrical contact, and trims the excess wire end.
3
Determine the application of a conduit bender.
A conduit bender is used to shape metal tubing to fit architectural paths.
The tool applies controlled leverage to form bends (such as 90-degree stubs and offsets) without kinking the conduit wall.
4
Determine the application of a knockout punch.
A knockout punch creates custom-sized circular entry holes in electrical panels.
The mechanical draw mechanism drives a hardened cutter through sheet steel to produce smooth openings for conduit connector fittings.

Anahtar Kavram

Specialized Electrical Installation and Termination Hand Tools
Tahmini Süre:1m 0s
Soru 10Soru →

An electronics technician is attaching an insulated ring lug to a multi-strand copper wire on an equipment harness. Which electrical hand tool is specifically designed to compress the metal terminal barrel securely around the wire strands without cutting the conductor or puncturing the protective nylon sleeve?

Cevabı ve açıklamayı göster

Cevap: Ratcheting terminal crimper with color-coded nesting dies

Cevap

Ratcheting terminal crimper with color-coded nesting dies
The ratcheting terminal crimper with color-coded nesting dies is engineered specifically for insulated terminations. The ratchet mechanism ensures that full, controlled compressive force is delivered before opening, creating a gas-tight mechanical bond while smoothly contouring around the nylon or vinyl insulation without puncturing it.

Adım Adım Çözüm

1
Identify the primary electrical task and safety constraints
The technician needs to mechanically secure an insulated terminal lug to stranded wire while preserving the integrity of the protective insulating jacket.
Insulated terminals require calibrated radial compression rather than sharp shearing or uncalibrated crushing force.
2
Evaluate tool mechanisms for terminal compression
Ratcheting crimpers utilize matched nest-and-indent dies designed to compress the metal barrel to a specified depth and release only after full cycle completion.
This guarantees a gas-tight, low-resistance mechanical bond without pinching or piercing the insulating sleeve.

Anahtar Kavram

Proper hand tool selection for insulated wire terminal crimping
Tahmini Süre:1m 0s
Soru 11Soru →

An electronics technician is installing a bootlace ferrule onto a flexible stranded copper wire before inserting it into a terminal block. Arrange the standard hand-tool steps in the correct chronological order from first to last.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence begins with cutting the wire to length using diagonal cutters, followed by stripping the insulation with wire strippers, inserting the bare conductor strands into the ferrule sleeve, and completing the process by compressing the sleeve with a ratcheting ferrule crimper.
Proper wire termination follows a sequential order: first, sizing and cutting the wire cleanly with diagonal cutters; second, stripping the insulation to the exact required length using properly sized wire strippers without damaging strands; third, gathering all conductor strands into the ferrule collar; and fourth, applying calibrated pressure with a ratcheting crimping tool to ensure a secure, low-resistance termination.

Adım Adım Çözüm

1
Trim the stranded wire cleanly to the desired working length using diagonal cutting pliers.
A clean, square end on the insulated wire ready for preparation.
Establishing the proper wire length and a clean cut prevents frayed strands and uneven ends before stripping.
2
Select the correct gauge notch on a wire stripper and strip the insulation to match the ferrule metal barrel length.
Exposed copper strands with zero severed or nicked conductors.
Using the properly sized stripper notch removes only the insulation jacket, preserving full current-carrying capacity.
3
Insert all exposed conductor strands into the barrel of the bootlace ferrule until the insulation enters the plastic collar.
The ferrule is positioned with all strands contained inside the conductive sleeve.
Ensuring no stray strands escape prevents short circuits and ensures maximum contact area.
4
Place the ferrule into the die of a ratcheting ferrule crimper and cycle the tool until full compression is achieved.
A compacted, square or hexagonal crimped termination.
The ratcheting mechanism ensures uniform crimping pressure for high mechanical pull-out strength and low electrical resistance.

Anahtar Kavram

Proper procedural sequence for wire preparation and termination using dedicated electrical hand tools
Soru 12Soru →

An electrician is selecting specialized hand tools for rough-in wiring, conduit preparation, and electrical panel assembly. Match each specialized electrical hand tool with its primary designated application.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Öğeler

Conduit reamer
Rotary armored cable cutter
Insulated torque screwdriver
Curved-jaw cable cutter

Eşleşmeler

Cevabı ve açıklamayı göster

Cevap

Conduit reamer matches deburring cut metal tubing; Rotary armored cable cutter matches slitting spiral metal cladding; Insulated torque screwdriver matches tightening terminal lugs to specified torque with 1,000 V shock protection; Curved-jaw cable cutter matches shearing large-diameter cables cleanly.
Each tool serves a dedicated mechanical and safety role in electrical work: conduit reamers eliminate sharp burrs that can pierce conductor insulation; rotary armored cable cutters cleanly sever metallic jackets without damaging internal wiring; insulated torque screwdrivers achieve calibrated fastener tension alongside 1,000 V shock protection; and curved-jaw cable cutters shear heavy-gauge conductors cleanly without crushing.

Adım Adım Çözüm

1
Identify the primary function of a conduit reamer.
Matches deburring the sharp inner rim of cut metal tubing.
Sawing metal conduit leaves jagged ridges that will strip wire insulation unless reamed smooth prior to wire pulling.
2
Identify the primary function of a rotary armored cable cutter.
Matches slitting spiral metal cladding on flexible shielded cable without nicking conductors.
The tool uses an adjustable blade depth stop to score only the exterior aluminum or steel casing, leaving underlying conductors intact.
3
Identify the primary function of an insulated torque screwdriver.
Matches tightening terminal lugs to manufacturer-specified torque with 1,000 V dielectric protection.
Calibrated torque prevents loose, high-resistance terminations or stripped screw heads, while certified dielectric insulation protects against accidental electrical contact.
4
Identify the primary function of a curved-jaw cable cutter.
Matches shearing large-diameter multi-strand power cables cleanly without crushing.
Bypass curved blades capture round conductors and apply even shearing force rather than flattening or fraying heavy strands.

Anahtar Kavram

Dedicated Applications of Specialized Electrical Hand Tools
Tahmini Süre:1m 15s
Soru 13Soru →

When stripping the insulation from a multi-strand copper wire using a standard manual wire stripper, what direct problem occurs if a technician selects a stripping notch calibrated for a wire gauge smaller than the conductor's actual gauge?

Cevabı ve açıklamayı göster

Cevap: The stripping blades cut too deeply into the core, nicking or severing outer conductor strands and degrading electrical and mechanical integrity.

Cevap

The stripping blades cut too deeply into the core, nicking or severing outer conductor strands and degrading electrical and mechanical integrity.
Manual wire strippers feature precisely sized cutting notches matching standard American Wire Gauge (AWG) conductor diameters. When an undersized notch is used, the cutting aperture is smaller than the outside diameter of the conductor core. When closed, the hardened steel blades penetrate completely through the insulation and score, nick, or cut off outer copper strands. This diminishes the conductor's current-carrying cross section and creates mechanical weak points prone to fatigue failure.

Adım Adım Çözüm

1
Analyze the mechanical relationship between wire stripper notch sizing and wire gauge numbers.
In the American Wire Gauge (AWG) system, a higher gauge number corresponds to a smaller conductor diameter, meaning a notch labeled for a smaller wire has a narrower cutting opening.
Understanding AWG sizing ensures the technician recognizes that selecting a smaller wire's notch creates an aperture smaller than the wire being stripped.
2
Determine the physical impact of the undersized opening on the conductor core.
Because the notch diameter is smaller than the copper core's overall diameter, the sharp cutting edges penetrate beyond the insulation layer and bite into the copper strands.
Wire strippers are designed so that the cutting blades only slice through the outer insulating sheath without scoring the metal underneath.
3
Evaluate the operational consequences of nicked or severed conductor strands.
Nicking creates stress concentration points where strands can easily snap under vibration, while severed strands reduce the effective cross-sectional area, increasing circuit resistance and heat buildup.
Preserving all conductor strands is essential for maintaining both mechanical durability and rated electrical ampacity.

Anahtar Kavram

Wire Stripper Gauge Calibration and Conductor Damage Prevention
Tahmini Süre:1m 0s
Soru 14Soru →

A technician is selecting hand tools to work inside an electrical enclosure containing potentially energized components. Which feature distinguishes a certified electrically insulated hand tool from a tool with standard dipped handles?

Cevabı ve açıklamayı göster

Cevap: A certified double-insulated dielectric barrier rated for protection up to 1,000 volts

Cevap

A certified double-insulated dielectric barrier rated for protection up to 1,000 volts
Certified insulated hand tools are engineered and rigorously tested with multi-layer dielectric materials to withstand up to 1,000 volts AC (1,500 volts DC), protecting the user from accidental electrocution and arc flash hazards.

Adım Adım Çözüm

1
Identify the electrical safety requirements for hand tools used in the vicinity of energized conductors.
Tools must provide a certified non-conductive barrier to prevent current from traveling through the tool body into the operator.
Accidental contact with live terminals creates a lethal shock hazard without proper dielectric insulation.
2
Distinguish between ergonomic coatings and certified electrical insulation.
Standard plastic or vinyl dips are non-rated and porous, whereas certified insulated tools comply with standards (such as ASTM F1505 or IEC 60900) rated for 1,000 V AC.
Only tools explicitly tested and stamped with the official 1,000 V symbol guarantee operator protection.

Anahtar Kavram

Certified 1,000V Insulated Hand Tools vs. Non-Rated Ergonomic Grips
Tahmini Süre:1m 0s
Soru 15Soru →

A technician is trimming excess component leads on the solder side of a printed circuit board after through-hole assembly. Which hand tool is designed to produce a flat, clean cut closest to the circuit board surface without stressing the solder joint?

Cevabı ve açıklamayı göster

Cevap: Flush cutters

Cevap

Flush cutters are the appropriate hand tool for creating flat, low-profile lead cuts on circuit boards.
Flush cutters (also called micro-shears or flush-cut diagonal pliers) are specifically designed with flat outside blade faces. This allows the cutting edge to rest directly against the printed circuit board surface and slice cleanly through component leads without creating a raised point or exerting high mechanical shock on delicate solder joints.

Adım Adım Çözüm

1
Identify the functional requirements for trimming through-hole component leads on a printed circuit board.
The tool must cut very close to the board surface and leave a flat profile without mechanical shock that could fracture solder joints.
Standard diagonal cutters have double-beveled jaws that pinch the lead into a sharp apex, which can bridge contacts or bend solder pads.
2
Evaluate the blade geometry of available electrical hand tools.
Flush cutters have a flat shearing surface on the back of the cutting jaw that rests directly against the board.
This flat profile produces a clean, low-profile cut that prevents chassis shorts and protects delicate circuit traces.

Anahtar Kavram

Selecting specialized electrical cutting tools based on blade geometry and delicate electronics assembly requirements.
Tahmini Süre:45s
Electrical Hand Tools Alıştırma Soruları — Armed Services Vocational Aptitude Battery (ASVAB) | Examkin