Examkin

Friction and Resistance

23 soru

Tüm türler23Çoktan seçmeli11Eşleştirme7Sıralama5
Soru 1Soru →

Match each practical mechanical scenario or design observation to the fundamental principle of friction and resistance that best explains it.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Öğeler

Towing a vehicle sideways with locked wheels requires the same lateral force regardless of whether the vehicle is equipped with wide mud tires or narrow street tires, assuming identical total vehicle weight.
Replacing solid bronze journal bearings in a high-speed rotary shaft with steel ball bearings dramatically reduces operating temperatures and mechanical energy loss.
A heavy crate resting on a steel ramp remains stationary as the incline is slowly raised, until it suddenly breaks loose and accelerates rapidly down the ramp without any additional pushing.
A submersible vehicle requires significantly more engine power to increase its cruising speed from 3030 knots to 4040 knots than it does to accelerate from 1010 knots to 2020 knots.

Eşleşmeler

Cevabı ve açıklamayı göster

Cevap

The locked wheels scenario pairs with area independence; the bearing replacement pairs with the advantage of rolling resistance over sliding; the accelerating crate pairs with the static friction threshold being overcome by kinetic friction; and the submersible's power demand pairs with the non-linear scaling of fluid drag.
Each scenario perfectly illustrates a unique property of friction: area independence for kinetic sliding, the mechanical advantage of rolling over sliding, the maximum threshold of static resistance transitioning to kinetic, and the velocity-dependent nature of fluid drag.

Adım Adım Çözüm

1
Analyze the tire width scenario.
Identify that changing tire width alters contact area but not vehicle weight or normal force.
The kinetic friction formula (Fk=μkNF_k = \mu_k N) shows that resistance depends strictly on normal force and material coefficient, not surface area.
2
Analyze the bearing replacement scenario.
Recognize the mechanical shift from a journal (sliding) bearing to a ball (rolling) bearing.
Rolling friction coefficients are fundamentally much smaller than sliding kinetic friction coefficients, significantly reducing heat and energy loss.
3
Analyze the sliding crate scenario.
Identify the transition state from stationary to moving.
Static friction resists movement up to a maximum limit (Fs(max)=μsNF_{s(max)} = \mu_s N). Once this is broken, the typically lower kinetic friction takes over, resulting in a sudden net force that causes acceleration.
4
Analyze the submersible speed scenario.
Identify that motion occurs through a fluid medium (water).
Unlike dry kinetic friction which is relatively constant across speeds, fluid drag increases with the square of the velocity, requiring exponentially more power at higher speeds.

Anahtar Kavram

Principles of Static, Kinetic, Rolling, and Fluid Friction
Soru 2Soru →

In mechanical engineering, understanding the dominant forces at contact interfaces is critical for system design. Match each practical mechanical scenario to the primary type of friction or resistance that governs its operation.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Öğeler

The interaction between a heavily loaded conveyor belt and its drive pulley that allows maximum torque transfer without slipping.
An automotive tire locked by a braking system failure, skidding across a dry asphalt road.
An engine crankshaft supported entirely by a pressurized wedge of oil within a hydrodynamic journal bearing.
The localized material deformation at the contact patch between hardened steel spheres and the raceway in a high-speed wheel hub.

Eşleşmeler

Cevabı ve açıklamayı göster

Cevap

The conveyor belt pairs with Static Friction; the skidding tire pairs with Kinetic (Sliding) Friction; the oil-supported crankshaft pairs with Viscous/Fluid Resistance; and the steel spheres pair with Rolling Resistance.
Each mechanical scenario operates under a distinct physical resistance mechanism. Static friction transfers torque when parts move together without slipping. Kinetic friction dominates during sliding events like skidding. Viscous resistance occurs when fluids separate moving parts, and rolling resistance occurs due to material deformation in rolling elements.

Adım Adım Çözüm

1
Analyze the contact interface of the conveyor belt.
Identify that the belt does not slip against the drive pulley.
Since the surfaces are stationary relative to one another at the point of contact, the force transferring the torque is static friction.
2
Analyze the state of the skidding automotive tire.
Identify that the rubber is actively sliding across the asphalt.
Sliding motion between two dry solid surfaces is always characterized by kinetic (sliding) friction.
3
Analyze the hydrodynamic journal bearing supporting the crankshaft.
Identify that a pressurized oil film entirely separates the solid components.
Because there is no solid-to-solid contact, the resistance to rotation is purely the viscous drag of the fluid.
4
Analyze the spheres in the high-speed wheel hub.
Identify that the spheres roll along the raceway rather than sliding.
The continuous micro-deformation of the materials as they roll creates energy loss, which defines rolling resistance.

Anahtar Kavram

Identifying applied frictional forces in complex mechanical systems
Tahmini Süre:1m 30s
Soru 3Soru →

A driver must execute an emergency stop on a dry asphalt road. The vehicle is equipped with an anti-lock braking system (ABS) that uses threshold braking, allowing the tires to continue rotating just on the verge of locking up. If the ABS were disabled and the driver fully locked the brakes, causing the tires to skid continuously across the surface, how would the frictional resistance between the tires and the road change?

Cevabı ve açıklamayı göster

Cevap: The resistance would decrease, because the skidding tires rely on kinetic friction, which is generally weaker than the maximum static friction maintained during threshold braking.

Cevap

The resistance would decrease, because the skidding tires rely on kinetic friction, which is generally weaker than the maximum static friction maintained during threshold braking.
As long as a tire is rolling without slipping (as is maintained during threshold braking), the exact point of the tire touching the road is momentarily stationary relative to the ground. This means it utilizes static friction. Once the brakes lock and the tire skids, the rubber slides across the surface, switching the force to kinetic friction. Because the coefficient of static friction is greater than the coefficient of kinetic friction, a sliding tire actually provides less overall stopping resistance than a tire rolling on the verge of locking.

Adım Adım Çözüm

1
Identify the type of friction present during threshold braking when the tires are still rotating.
The bottom of a rolling tire does not slide against the road, meaning the system utilizes static friction at the contact patch.
Understanding the physical state of rolling without slipping is necessary to determine the active frictional forces.
2
Identify the type of friction present during a full brake lockup (skid).
When the tires lock, they slide across the asphalt, meaning the system transitions to utilizing kinetic (sliding) friction.
Skidding fundamentally changes the interaction between the surfaces from gripping to sliding.
3
Compare the magnitudes of the relevant friction coefficients.
For standard materials like rubber on asphalt, the coefficient of static friction is greater than the coefficient of kinetic friction.
This physical rule dictates which braking method provides the most stopping force.
4
Determine the net effect on frictional resistance.
Because kinetic friction is weaker than maximum static friction, locking the brakes and skidding results in decreased frictional resistance.
Combining the physical state with the friction coefficients provides the final answer.

Anahtar Kavram

Static versus Kinetic Friction in Rolling Mechanisms
Soru 4Soru →

An automotive engineer is designing a mechanical disc brake system to stop a heavy rotating axle. The engineer is evaluating two brake pad designs made of the exact same friction material: Design X utilizes a single large brake pad, while Design Y utilizes a smaller brake pad with exactly half the surface area of Design X. During a braking event, the hydraulic system applies an identical clamping force (normal force) to the pad in both designs. Assuming the coefficient of kinetic friction remains constant, which of the following best describes the resulting kinetic frictional resistance and the reasoning behind it?

Cevabı ve açıklamayı göster

Cevap: Both designs produce the same kinetic frictional resistance because the total frictional force depends on the applied clamping force and the coefficient of friction, regardless of the contact area.

Cevap

Both brake pad designs produce the identical amount of kinetic frictional resistance because macroscopic friction is independent of the contact surface area.
The correct answer accurately applies the standard physical model of kinetic friction, where the total frictional force (FkF_k) is solely the product of the coefficient of kinetic friction (μk\mu_k) and the normal force (FnF_n). Because both brake pad designs are made of identical material and are subjected to the exact same hydraulic clamping force, the resulting kinetic friction is identical. In solid mechanics, sliding friction does not depend on the macroscopic surface area in contact.

Adım Adım Çözüm

1
Identify the primary equation used to calculate kinetic friction.
Fk=μk×FnF_k = \mu_k \times F_n
This formula establishes that kinetic frictional force (FkF_k) depends strictly on the coefficient of kinetic friction (μk\mu_k) and the normal force (FnF_n).
2
Evaluate the variables given in the scenario for both designs.
Both designs possess the same normal force (identical clamping force) and the same coefficient of friction (exact same friction material).
The prompt explicitly states the hydraulic system applies an identical clamping force and the materials are the same.
3
Determine the impact of the differing surface areas on the total frictional force.
The surface area does not affect the calculation. Both designs yield the exact same frictional resistance.
Surface area is not a variable in the standard kinetic friction formula; increased area distributes the force resulting in lower pressure, while decreased area concentrates the force resulting in higher pressure, keeping total friction constant.

Anahtar Kavram

Independence of kinetic friction from surface area
Soru 5Soru →

A heavy rectangular crate is being dragged across a level warehouse floor. If the crate is stopped, flipped to rest on its narrowest side, and then dragged again, how will the force of sliding friction change?

Cevabı ve açıklamayı göster

Cevap: It remains the same.

Cevap

The force of sliding friction remains the same.
The correct answer states that friction remains the same. According to the laws of classical physics, sliding (kinetic) friction is determined by multiplying the normal force (the weight of the crate) by the coefficient of friction (the material properties of the floor and crate). Because flipping the crate changes neither its overall weight nor the materials involved, the total frictional resistance remains unchanged.

Adım Adım Çözüm

1
Identify the factors that determine sliding friction.
Sliding friction relies on the normal force (the crate's weight) and the coefficient of friction (the roughness of the floor and crate materials).
These are the only physical variables present in the standard friction formula (F=μNF = \mu N).
2
Evaluate what changes when the crate is flipped.
The surface area touching the floor decreases, but the crate's mass, weight, and material remain exactly the same.
Flipping an object only changes its orientation, not its inherent properties.
3
Determine the impact of contact area on friction.
The frictional force does not change.
Because neither the normal force nor the surface materials have changed, the total resistance remains constant regardless of the contact area size.

Anahtar Kavram

Sliding friction depends only on the normal force and the coefficient of friction between the two surfaces, and is independent of the apparent area of contact.
Soru 6Soru →

Match each mechanical design feature with its primary physical effect on friction or resistance.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Öğeler

Applying lubricating oil to metal gear teeth
Installing steel ball bearings around a rotating axle
Molding deep rubber treads onto an off-road tire
Shaping an airplane fuselage with a smooth, streamlined nose

Eşleşmeler

Cevabı ve açıklamayı göster

Cevap

Lubricating oil decreases sliding friction, ball bearings convert sliding friction to rolling friction, heavy tire treads increase static friction, and a streamlined aerodynamic shape reduces fluid resistance.
Each feature is a standard engineering method for managing a specific form of resistance based on its application. Lubricants handle sliding friction, bearings manage rotational contact by rolling, treads ensure static friction for grip, and aerodynamics handle fluid resistance in the air.

Adım Adım Çözüm

1
Analyze each mechanical design feature to determine what materials or surfaces are interacting.
Gears involve metal-on-metal sliding; axles involve rotational contact; tires interact directly with the ground; airplanes interact with the air.
Identifying the interacting materials reveals the specific type of physical resistance involved in each scenario.
2
Determine whether the design goal of the feature is to increase or decrease the physical resistance.
Tires need increased friction for grip, while gears, axles, and airplanes need decreased resistance for mechanical efficiency.
Matching the design goal (grip vs. efficiency) with the physical mechanism leads to the correct pairings.

Anahtar Kavram

Methods of Controlling Friction and Resistance
Soru 7Soru →

A logistics team is evaluating the force required to slide various solid steel crates across a dry, level concrete warehouse floor at a constant velocity. Assume the coefficient of kinetic friction remains constant for all steel-on-concrete contact.

Rank the following sliding scenarios from the GREATEST kinetic frictional resistance to the LEAST kinetic frictional resistance.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence from greatest to least frictional resistance is the 200-pound crate, followed by the 150-pound crate, the 100-pound crate, and finally the 50-pound crate.
According to the laws of sliding friction, kinetic frictional force depends entirely on the coefficient of friction and the normal force (the object's weight on a level surface). It is completely independent of the surface area in contact. Therefore, the friction is determined solely by the weight of the crates. Arranging them strictly from heaviest to lightest correctly orders them from greatest to least frictional resistance.

Adım Adım Çözüm

1
Identify the governing mathematical relationship for kinetic friction.
The formula for kinetic friction is Fk=μk×FNF_k = \mu_k \times F_N, where μk\mu_k is the coefficient of kinetic friction and FNF_N is the normal force.
This establishes which physical properties actually affect sliding resistance.
2
Determine the impact of surface area on the calculation.
The apparent contact area (2 sq ft vs 10 sq ft) is not a variable in the friction equation.
According to Amontons' Second Law of Friction, dry sliding friction is independent of the apparent area of contact.
3
Calculate the normal force for each scenario.
On a level floor, the normal force is exactly equal to the weight of the object. The normal forces are 200 lbs, 150 lbs, 100 lbs, and 50 lbs.
The weight dictates how hard the two surfaces are pressed together.
4
Order the scenarios based on the normal force.
Highest to lowest normal force: 200 lbs, 150 lbs, 100 lbs, 50 lbs.
Because kinetic friction is directly proportional to normal force, ordering by weight correctly orders by total frictional resistance.

Anahtar Kavram

Amontons' Laws of Friction (Surface Area Independence)
Soru 8Soru →

A technician is modifying a heavy steel sliding door that currently drags directly along a flat metal base. To significantly reduce the frictional resistance required to open and close the door, which of the following design changes would be the most effective?

Cevabı ve açıklamayı göster

Cevap: Incorporating steel ball bearings or roller wheels between the door and the base.

Cevap

Incorporating steel ball bearings or roller wheels between the door and the base.
The correct answer identifies that converting sliding friction into rolling friction (by using wheels or bearings) is one of the most effective mechanical methods to reduce resistance. Rolling friction is generally much weaker than sliding friction because the contact surfaces do not grind against each other as they move.

Adım Adım Çözüm

1
Identify the type of friction currently acting on the door.
The door dragging flat against a metal track experiences kinetic (sliding) friction.
Understanding the current state helps identify how to improve the system.
2
Evaluate the options based on mechanical principles to find the best method for reducing resistance.
Adding wheels or ball bearings changes the interaction from sliding to rolling.
Rolling friction is significantly lower than sliding friction for hard materials like steel, making this the most effective mechanical improvement.

Anahtar Kavram

Rolling friction is substantially lower than sliding (kinetic) friction, which is why wheels and bearings are used in mechanical designs to reduce resistance.
Tahmini Süre:45s
Soru 9Soru →

A maintenance team needs to move a heavy steel generator across a flat concrete floor. Arrange the following methods in order from the HIGHEST amount of frictional resistance to the LOWEST amount of frictional resistance.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct order from highest to lowest resistance is: dragging directly on dry concrete, sliding with industrial lubricant, and placing on steel rollers.
Dry sliding friction creates the most resistance due to direct, rough surface-to-surface contact. Lubricating the surface reduces this resistance by creating a fluid film between the objects, lowering the friction coefficient. However, rolling friction (using rollers) is the most efficient method and creates the absolute least resistance, as it prevents the surfaces from scraping against each other entirely.

Adım Adım Çözüm

1
Identify the primary type of friction acting in each of the three moving methods.
Dragging directly involves dry sliding friction; using lubricant involves fluid or mixed friction; using steel rollers involves rolling friction.
Recognizing the physical mechanism at the contact surface is the first step in comparing resistance levels.
2
Compare the relative magnitudes of these different types of friction.
Dry sliding friction provides the greatest resistance due to interlocking surface irregularities. Lubrication reduces this contact, lowering resistance. Rolling friction provides the least resistance as sliding is eliminated.
Fundamental mechanical principles state that, for a given load, dry kinetic friction is generally greater than fluid friction, which in turn is greater than rolling friction.
3
Order the methods from highest frictional resistance to lowest.
Highest is dry dragging, middle is lubricated sliding, lowest is steel rollers.
This matches the sequence requirements specified in the question stem.

Anahtar Kavram

Types and relative magnitudes of mechanical friction
Tahmini Süre:45s
Soru 10Soru →

A heavy winch is dragging a 200 kg200\text{ kg} rectangular steel block across a flat, horizontal concrete surface at a constant velocity of 5 m/s5\text{ m/s}. The coefficient of kinetic friction between the steel and the concrete is 0.40.4. (Assume gravitational acceleration g=10 m/s2g = 10\text{ m/s}^2). What is the approximate kinetic frictional force opposing the block's motion, and how would this force change if the block were turned to slide on a face with only half the original surface area?

Cevabı ve açıklamayı göster

Cevap: 800 N800\text{ N}; the frictional force would remain exactly the same.

Cevap

The kinetic frictional force is 800 N800\text{ N}, and it would remain exactly the same if the surface area were halved.
The correct answer accurately calculates the normal force by multiplying mass and gravity (200×10=2000 N200 \times 10 = 2000\text{ N}), then applies the friction coefficient (2000×0.4=800 N2000 \times 0.4 = 800\text{ N}). Furthermore, it correctly applies the principle that sliding friction is unaffected by the size of the contact area, so the force remains constant regardless of which face the block slides on.

Adım Adım Çözüm

1
Calculate the weight (which equals the normal force) of the block.
W=mg=200 kg×10 m/s2=2000 NW = mg = 200\text{ kg} \times 10\text{ m/s}^2 = 2000\text{ N}. Since the surface is horizontal, the normal force N=2000 NN = 2000\text{ N}.
Kinetic friction is directly proportional to the normal force pressing the surfaces together.
2
Calculate the kinetic frictional force.
Fk=μk×N=0.4×2000 N=800 NF_k = \mu_k \times N = 0.4 \times 2000\text{ N} = 800\text{ N}.
The formula for kinetic friction requires multiplying the normal force by the coefficient of kinetic friction.
3
Evaluate the effect of changing the surface area.
The frictional force remains 800 N800\text{ N}.
Amontons' Second Law of Friction states that the force of friction is independent of the apparent area of contact. The pressure increases on the smaller area, but the total normal force remains unchanged.

Anahtar Kavram

Kinetic friction depends solely on the normal force and the materials in contact (coefficient of friction), and is completely independent of the contact surface area and velocity.
Soru 11Soru →

A mechanic needs to move a heavy steel block across a flat concrete floor. Which of the following actions will successfully decrease the frictional resistance between the block and the floor?

Cevabı ve açıklamayı göster

Cevap: Placing round steel pipes underneath the block to act as rollers

Cevap

Placing round steel pipes underneath the block to act as rollers.
Rolling friction is significantly lower than sliding (kinetic) friction. By placing round steel pipes under the heavy block, the sliding motion is converted into a rolling motion, which drastically reduces the physical effort and resistance required to move the object.

Adım Adım Çözüm

1
Identify the type of friction currently acting on the block.
The block is sliding directly across the floor, so sliding (kinetic) friction is present.
Understanding the current resistance is necessary to evaluate ways to reduce it.
2
Evaluate the physical effect of each proposed action.
Changing surface area has no effect on friction magnitude. Pressing down increases friction. A sudden strike cannot eliminate reaction forces. Using pipes changes the friction type entirely.
Applying physical laws to each option isolates the effective method.
3
Compare the magnitude of sliding friction to rolling friction.
Rolling friction is significantly lower than sliding friction for heavy objects on hard surfaces.
This confirms that using pipes as rollers is the mechanically correct way to decrease resistance.

Anahtar Kavram

Friction and Resistance (Rolling vs. Sliding Friction)
Tahmini Süre:45s
Soru 12Soru →

Match each type of frictional resistance to its correct mechanical description or real-world example.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Öğeler

Static Friction
Kinetic (Sliding) Friction
Rolling Friction
Fluid Friction

Eşleşmeler

Cevabı ve açıklamayı göster

Cevap

Static Friction matches with keeping a stationary object from moving; Kinetic Friction matches with scraping resistance between flat surfaces; Rolling Friction matches with ball bearings turning; Fluid Friction matches with aerodynamic drag.
Each classification of friction applies to a distinct mechanical interaction: static for preventing initial movement, kinetic for active sliding, rolling for rotating circular objects, and fluid for motion through gases or liquids.

Adım Adım Çözüm

1
Analyze the definition of static friction.
Matches with the resistance keeping a stationary heavy object from moving.
The term 'static' refers to objects that are at rest relative to each other.
2
Analyze the definition of kinetic or sliding friction.
Matches with the scraping resistance between two flat solid surfaces like brake pads.
The term 'kinetic' applies to objects that are currently in relative sliding motion.
3
Analyze the definition of rolling friction.
Matches with the minimal resistance of ball bearings turning.
Rolling friction specifically applies to round objects rotating over a surface.
4
Analyze the definition of fluid friction.
Matches with the aerodynamic drag force on a moving vehicle.
Air is a fluid, and drag is the fluid friction acting against moving objects.

Anahtar Kavram

Understanding the fundamental types of friction and how to identify them in practical mechanical scenarios.
Soru 13Soru →

A mechanic is servicing a high-speed gearbox and must choose a lubricant. If a heavy, thick grease is used instead of a lightweight oil, the gearbox will require more mechanical power to maintain its high rotational speeds. What is the primary cause of this increased resistance?

Cevabı ve açıklamayı göster

Cevap: The greater viscosity of the thick grease creates higher fluid friction against the moving gears.

Cevap

The greater viscosity of the thick grease creates higher fluid friction against the moving gears.
Thick grease has a high viscosity, meaning it strongly resists flow and deformation. When gears rotate at high speeds through this thick substance, they must continuously shear and displace the grease. This creates substantial fluid friction (drag), which opposes the motion of the gears and requires the system to draw more mechanical power to maintain its speed.

Adım Adım Çözüm

1
Identify the type of resistance introduced when machine parts move through a liquid or semi-solid substance.
The resistance is fluid friction, also known as drag or viscous resistance.
Because the gears are completely coated by a lubricant, they must continuously push the fluid out of the way as they spin.
2
Compare the physical properties of a lightweight oil and a thick grease.
Thick grease has a much higher viscosity than lightweight oil.
Viscosity is the measure of a fluid's internal resistance to flow and deformation.
3
Determine how this viscosity affects high-speed mechanical operation.
Higher viscosity results in greater fluid friction against the fast-moving gears, requiring more energy from the motor to maintain speed.
Moving through a thicker, more resistant substance requires more force than moving through a thinner one.

Anahtar Kavram

Fluid Friction and Viscosity
Soru 14Soru →

An engineering team is analyzing how different mechanical interactions affect the control and efficiency of an off-road vehicle. Match each vehicle component or scenario to the specific type of frictional resistance it primarily demonstrates.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Öğeler

The grip between stationary tires and a steep rock surface preventing backward slip
The rubbing action between clamped brake pads and steel rotors during an emergency stop
The resistance encountered by ball bearings as they rotate inside the wheel hubs
The drag force acting against the vehicle's body as it plows through deep mud

Eşleşmeler

Cevabı ve açıklamayı göster

Cevap

The correct matches are: stationary tires demonstrate Static Friction; brake pads demonstrate Kinetic Friction; ball bearings demonstrate Rolling Friction; and moving through mud demonstrates Fluid Friction.
Each mechanical scenario perfectly isolates one of the four primary types of friction. Stationary objects resisting motion rely on static friction. Surfaces sliding past one another generate kinetic friction. Round objects moving over a surface experience rolling friction. Objects moving through a liquid or gas encounter fluid friction.

Adım Adım Çözüm

1
Analyze the tire scenario
The tires are stationary relative to the rock surface.
Identifying that there is no relative motion points to static friction.
2
Analyze the brake pad scenario
The pads rub directly against the moving steel rotors.
Solid surfaces sliding against each other exhibit kinetic (sliding) friction.
3
Analyze the ball bearing scenario
The bearings roll along their inner and outer races.
Objects rolling over a surface experience rolling friction, which is much lower than sliding friction.
4
Analyze the mud scenario
The vehicle body pushes through a semi-liquid medium.
Moving through liquids or gases involves fluid (viscous) friction.

Anahtar Kavram

Types of Frictional Resistance in Mechanics
Soru 15Soru →

A rubber drive belt is slipping on a steel motor pulley because there is insufficient frictional resistance between the two surfaces. Which of the following adjustments will most effectively increase the frictional force to prevent the belt from slipping?

Cevabı ve açıklamayı göster

Cevap: Increasing the tension on the drive belt

Cevap

Increasing the tension on the drive belt
The correct adjustment increases the belt's tension. Friction depends on two main factors: the materials involved (coefficient of friction) and how hard they are pressed together (normal force). In a mechanical drive system, increasing the belt tension pulls the belt tighter around the pulley, directly increasing the normal force pressing inward. This higher normal force generates a proportionally higher static friction, giving the belt better grip to prevent slipping.

Adım Adım Çözüm

1
Identify the formula and components of mechanical friction.
The maximum static frictional force is determined by the equation Ff=μFNF_f = \mu F_N, where μ\mu is the coefficient of friction and FNF_N is the normal force.
Understanding the mathematical relationship reveals which physical variables can be manipulated to change the friction.
2
Determine how normal force is generated in a belt and pulley system.
The normal force (the force pressing the belt perpendicularly into the face of the pulley) is generated by the tension pulling on the ends of the belt.
To increase FNF_N (and thereby increase FfF_f), we must increase the force that squeezes the two components together.
3
Evaluate the given modifications.
Increasing the tension directly increases the normal force. Changing the surface area or pulley mass does not affect the normal force between the mating surfaces.
This confirms that tightening the belt is the mechanically correct method to stop slipping.

Anahtar Kavram

Frictional force is directly proportional to the normal force pressing two surfaces together, and in a belt-drive system, this normal force is created by belt tension.
Tahmini Süre:1m 0s
Soru 16Soru →

A heavy steel block must be moved along a level track. Rank the following methods or conditions based on the amount of frictional resistance they generate, from LEAST resistance to GREATEST resistance.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct order from least to greatest resistance is: floating on oil (fluid friction), moving on rollers (rolling friction), sliding continuously (kinetic friction), and overcoming the initial standstill (static friction).
Fluid friction separates the surfaces entirely, offering the least resistance. Rolling friction prevents surfaces from dragging, making it the second lowest. For the dry track, sliding (kinetic) friction is less than the static friction required to break the object's initial grip, making static friction the greatest resistance.

Adım Adım Çözüm

1
Identify the primary type of friction acting in each scenario.
Oil film involves fluid friction; steel rollers involve rolling friction; continuous sliding involves kinetic friction; breaking free from a standstill involves static friction.
Categorizing the physical interaction is required to compare their relative magnitudes.
2
Determine the lowest sources of friction.
Fluid friction creates the least resistance, followed closely by rolling friction.
Fluids deform easily to allow movement and separate the surfaces entirely, while rollers prevent direct surface scraping.
3
Compare the resistance of a moving object versus a stationary object on the exact same dry surface.
Kinetic (sliding) friction is always less than the maximum static (standstill) friction.
Once the microscopic bonds between the resting surfaces are broken, it takes less force to keep the object moving than it did to start it.
4
Arrange the scenarios from least to greatest based on these physical principles.
The correct sequence is: Fluid, Rolling, Kinetic, Static.
This correctly orders the magnitudes of frictional resistance from lowest to highest.

Anahtar Kavram

Friction and Resistance
Soru 17Soru →

A mason is pushing a solid, uniform rectangular clay brick across a horizontal wooden scaffold plank at a constant speed. Initially, the brick is positioned so it slides while resting flat on its widest face. If the mason stands the brick up so it slides on its narrowest face across the same section of the plank, how will the kinetic frictional resistance change?

Cevabı ve açıklamayı göster

Cevap: It will remain unchanged because kinetic friction depends on normal force and surface materials, not contact area.

Cevap

The kinetic frictional resistance will remain unchanged.
For standard rigid objects, the kinetic frictional force is determined solely by the nature of the materials in contact (the coefficient of friction) and the total force pressing them together (the normal force). Because the brick's mass and the materials involved do not change when it is rotated, the overall frictional resistance remains exactly the same, regardless of how much surface area is touching the plank.

Adım Adım Çözüm

1
Identify the formula for kinetic friction.
Fk=μk×NF_k = \mu_k \times N
To determine exactly which physical variables affect the frictional force.
2
Analyze the normal force (NN).
The normal force equals the weight of the brick (N=mgN = mg), which remains constant regardless of its orientation.
To see if rotating the brick changes the total downward force pressing the surfaces together.
3
Analyze the coefficient of kinetic friction (μk\mu_k).
The coefficient remains constant because the materials (clay and wood) and their surface properties have not changed.
To verify that the fundamental physical interaction between the two specific surfaces remains the same.
4
Evaluate the effect of surface contact area.
Surface area is not a variable in the standard kinetic friction formula.
To conclusively confirm that resting the brick on a narrower face does not alter the total frictional resistance.

Anahtar Kavram

Independence of Friction from Surface Area
Soru 18Soru →

Match each mechanical adjustment to its primary physical effect on frictional resistance.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Öğeler

Introducing motor oil between two dry, sliding metal plates
Adding heavier cargo to a pallet being dragged across a level floor
Installing ball bearings between a rotating axle and its housing
Turning a sliding rectangular crate so it rests on its largest face instead of its smallest face

Eşleşmeler

Cevabı ve açıklamayı göster

Cevap

Motor oil decreases the coefficient of friction; adding cargo increases the normal force; ball bearings replace sliding friction with rolling friction; and changing the resting face of a crate leaves the frictional resistance unchanged.
Each adjustment demonstrates a fundamental principle of friction. Oil modifies the surface interaction (lowering the coefficient of friction). Added mass increases the normal force (increasing total resistance). Bearings change the physical mechanism from sliding to rolling. Finally, rotating the crate tests the principle that friction is independent of the contact area.

Adım Adım Çözüm

1
Analyze the effect of motor oil.
It creates a fluid boundary layer.
Lubrication physically separates the sliding metal surfaces, which directly reduces the coefficient of friction.
2
Analyze the effect of heavier cargo.
The downward force on the floor increases.
Friction is proportional to normal force. More weight means a greater normal force, increasing total frictional resistance.
3
Analyze the effect of ball bearings.
Sliding motion is converted to rolling motion.
Rolling friction relies on point or line contact and avoids the continuous shearing of surface asperities seen in sliding friction.
4
Analyze the effect of changing the crate's contact area.
The frictional force does not change.
According to Coulomb's laws of friction, kinetic friction is independent of the apparent area of contact as long as the mass (and thus normal force) remains constant.

Anahtar Kavram

Friction and Resistance
Soru 19Soru →

A delivery truck is attempting to climb a slippery, snow-covered hill, but its rear drive wheels begin to spin in place. The driver stops and shifts several heavy crates from the front of the trailer to a position directly over the rear drive axle. What is the primary physical reason this action helps the truck regain traction?

Cevabı ve açıklamayı göster

Cevap: It increases the normal force pressing the drive tires against the road surface, which increases the maximum available frictional force.

Cevap

The action increases the normal force pressing the drive tires against the road surface, which increases the maximum available frictional force.
Traction is the practical application of static friction between a tire and a road surface. Frictional resistance depends on two primary factors: the coefficient of friction (the slipperiness of the snow and rubber) and the normal force (the force pressing the two surfaces together). By shifting heavy cargo directly over the drive axle, the downward force on those specific wheels increases. This increases the normal force, which directly increases the maximum available friction, allowing the tires to grip the snow rather than spin.

Adım Adım Çözüm

1
Analyze the cause of the wheels spinning.
The driving force exerted by the engine exceeds the maximum static friction available between the tires and the snow, causing kinetic friction (slipping) instead.
To move forward without slipping, static friction must be greater than or equal to the driving force.
2
Determine the physical effect of shifting the crates.
Moving the heavy crates directly over the rear drive axle increases the concentrated downward weight on those specific wheels.
Weight distribution affects how much force is applied to different parts of the vehicle.
3
Relate the increased weight to frictional force.
The increased weight increases the normal force (FNF_N) pushing the tires into the ground. Since friction (Ff=μFNF_f = \mu F_N) is directly proportional to normal force, the maximum static friction increases.
Frictional resistance relies on the normal force; greater normal force yields greater traction.

Anahtar Kavram

The maximum force of static friction (traction) is directly proportional to the normal force pressing two surfaces together.
Soru 20Soru →

A heavy steel crate must be moved across a horizontal concrete floor. Rank the following conditions based on the magnitude of frictional resistance opposing the applied force, from LEAST resistance to GREATEST resistance.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence from least to greatest frictional resistance is: using wheels (rolling friction), sliding on oil (fluid friction), sliding at a constant speed (kinetic friction), and pushing just prior to movement (static friction).
Frictional resistance follows a predictable hierarchy based on how surfaces interact. Rolling friction is the lowest because there is no sliding action. Fluid friction is next, as the fluid layer prevents solid-to-solid contact. Dry kinetic (sliding) friction is higher because the solids scrape directly against each other. Finally, static friction is the highest because the microscopic peaks and valleys of the stationary surfaces have settled deeply into one another.

Adım Adım Çözüm

1
Identify the type of friction present in each condition.
Wheels = rolling friction; Oil = fluid friction; Sliding = kinetic friction; Stationary just before moving = static (breakaway) friction.
Different physical mechanisms govern resistance in each scenario.
2
Compare rolling friction to all forms of sliding friction.
Rolling friction is ranked lowest (least resistance).
Rolling mechanisms are specifically designed to eliminate the dragging forces characteristic of sliding.
3
Evaluate the lubricated surface against the dry surfaces.
Fluid friction is ranked second lowest.
Lubricants separate the solid surfaces, drastically reducing resistance compared to dry contact, but generally offer more resistance than precision wheel bearings.
4
Compare the two dry conditions: moving at constant speed vs. about to move.
Kinetic friction is ranked third, and static friction is ranked highest.
The coefficient of static friction is typically greater than the coefficient of kinetic friction for the same materials; it takes more force to start an object moving than to keep it moving.

Anahtar Kavram

Types of Friction (Static, Kinetic, Rolling, Fluid)
Sayfa 1 / 2Sonraki
Friction and Resistance Alıştırma Soruları — Armed Services Vocational Aptitude Battery (ASVAB) | Examkin