Examkin

Structural Support and Materials

77 soru

Tüm türler77Çoktan seçmeli39Doğru / Yanlış13Sayısal5Eşleştirme13Sıralama7
Soru 61Soru →

When fastening a rigid steel bracket to a softer aluminum base, a wide, flat metal washer is typically placed beneath the bolt head and nut. Which of the following best describes the primary mechanical function of this flat washer?

Cevabı ve açıklamayı göster

Cevap: It distributes the compressive clamping force over a larger surface area to prevent crushing the softer material.

Cevap

It distributes the compressive clamping force over a larger surface area to prevent crushing the softer material.
The correct answer accurately identifies that a flat washer increases the bearing area under the fastener. Because mechanical pressure is equal to force divided by area (P=FAP = \frac{F}{A}), increasing the contact area reduces the localized compressive stress on the softer material, preventing the bolt head from sinking into or crushing it.

Adım Adım Çözüm

1
Analyze the forces acting on a joint when a bolt is tightened.
Tightening the bolt creates tension within the bolt shaft and downward compressive force against the clamped materials.
Understanding the primary stresses in a bolted joint is necessary to evaluate component functions.
2
Evaluate the material properties given in the scenario.
Aluminum is softer than steel and has a lower compressive yield strength, making it vulnerable to high localized pressure.
Identifying the weak point in the assembly explains why additional hardware is needed.
3
Apply the mechanical relationship between force, area, and pressure (P=FAP = \frac{F}{A}).
The flat washer has a much larger diameter than the bolt head. By spreading the same clamping force over this larger area, the overall pressure is significantly reduced.
This calculation proves that a larger surface area prevents the compressive stress from exceeding the aluminum's yield strength.

Anahtar Kavram

Load Distribution and Surface Pressure in Bolted Joints
Soru 62Soru →

A winch cable made of steel is subjected to heavy pulling forces. The cable can stretch slightly under this tension rather than snapping instantly. Which material property allows the steel to stretch and deform under pulling forces without breaking?

Cevabı ve açıklamayı göster

Cevap: Ductility

Cevap

Ductility
Ductility is the specific mechanical property that allows a material to be drawn out or stretched under tension without fracturing. This makes it ideal for cables that must handle pulling forces safely.

Adım Adım Çözüm

1
Identify the type of force acting on the cable.
The cable is subjected to heavy pulling forces, which is known as tension.
Understanding the force helps determine which material property is relevant.
2
Determine which material property describes stretching under tension.
Ductility is the property that allows a material to deform or stretch under tensile stress without breaking.
Matching the force (tension) and behavior (stretching) to the correct definition isolates the correct property.

Anahtar Kavram

Ductility and Tensile Stress
Tahmini Süre:45s
Soru 63Soru →

A uniform steel bar is 1010 feet long and weighs 200200 pounds. It is placed on a pivot located exactly 22 feet from its left end. To keep the bar perfectly horizontal, a downward force must be applied to the extreme left end. What is the magnitude of this downward force?

Cevabı ve açıklamayı göster

Cevap: 300300 pounds

Cevap

The required downward force is 300300 pounds.
To maintain a horizontal position, the torques around the pivot must balance perfectly. Because the bar is uniform, its entire 200200-pound weight acts at its center of gravity, which is 55 feet from the end. The pivot is located 22 feet from the left end, meaning the center of gravity is exactly 33 feet to the right of the pivot (5−2=35 - 2 = 3). This creates a clockwise torque of 600600 lb-ft (200200 lbs ×\times 33 ft). To balance this rotation, a downward force applied at the left end (which is 22 feet from the pivot) must create an equal 600600 lb-ft counter-clockwise torque. Dividing the required 600600 lb-ft by the 22-foot distance gives a required downward force of 300300 pounds.

Adım Adım Çözüm

1
Determine the location of the center of gravity (CG).
The CG is exactly in the middle of the 1010-foot bar, which is 55 feet from either end.
A uniform object's weight is evenly distributed, so its total weight acts geometrically at its center.
2
Calculate the distances from the pivot point.
The left end is 22 feet from the pivot. The CG is 33 feet from the pivot (55 feet - 22 feet).
Torque is calculated using the distance from the exact pivot (fulcrum) to the point where the force acts.
3
Calculate the clockwise torque created by the bar's weight.
200200 lbs ×\times 33 ft = 600600 lb-ft.
The weight of the bar pulls down on the right side of the pivot, creating a clockwise rotational tendency.
4
Calculate the required counter-clockwise force at the left end.
Force ×\times 22 ft = 600600 lb-ft, which means Force = 300300 lbs.
For the bar to remain horizontal (in equilibrium), the counter-clockwise torque must exactly balance the clockwise torque.

Anahtar Kavram

Principle of Moments (Torque Equilibrium)
Soru 64Soru →

A uniform 1010-foot wooden beam weighing 5050 pounds is placed on a flat surface. In four different scenarios, exactly 150150 pounds of additional weight is placed on the beam in various configurations. Arrange the scenarios in order of the beam's overall balance point (center of gravity), measured from the LEFT end of the beam, from the GREATEST distance to the LEAST distance.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct order from greatest to least distance from the left end is: the two 7575-pound weights (furthest right), the 5050/100100-pound weights, the 100100/5050-pound weights, and finally the single 150150-pound weight (closest to the left).
Because the total system weight is identical (200200 lbs) in every scenario, the relative position of the center of gravity is determined purely by the sum of the moments (weight ×\times distance) of the added weights from the left end. Calculating these moments yields 10501050, 900900, 600600, and 450450 ft-lbs respectively. A larger moment means the center of gravity is pulled further to the right, which translates to a greater overall distance from the left end.

Adım Adım Çözüm

1
Identify the components that determine the overall center of gravity (balance point).
The center of gravity's distance from an origin (the left end) is found by dividing the total turning moment (torque) by the total weight of the system.
This is the fundamental principle of moments for finding the balance point of a loaded beam.
2
Observe the constants across all four scenarios.
In every scenario, the total system weight is identical at 200200 lbs (5050 lb beam + 150150 lbs of added weight), and the beam's own moment from the left end remains constant.
Because the total weight denominator is identical across all choices, the relative position of the balance point is determined solely by the sum of the moments of the added weights.
3
Calculate the turning moment (Weight ×\times Distance) of the added weights relative to the left end for each scenario.
Two 7575-lb weights: (75×4)+(75×10)=1050(75 \times 4) + (75 \times 10) = 1050 ft-lbs.
5050-lb and 100100-lb weights: (50×2)+(100×8)=900(50 \times 2) + (100 \times 8) = 900 ft-lbs.
100100-lb and 5050-lb weights: (100×2)+(50×8)=600(100 \times 2) + (50 \times 8) = 600 ft-lbs.
Single 150150-lb weight: 150×3=450150 \times 3 = 450 ft-lbs.
This calculation provides a numerical value directly proportional to how far right the weight is biased.
4
Order the scenarios by their added moments from greatest to least.
The order is 1050>900>600>4501050 > 900 > 600 > 450. Therefore, the balance point distances follow the exact same order.
A greater turning moment from the left end means the center of gravity is located further to the right, which translates to a greater distance from the left end.

Anahtar Kavram

The center of gravity of a system shifts proportionally toward the location with the greatest turning moment (Force ×\times Distance). When total mass is constant, ranking moments ranks the balance points.
Tahmini Süre:1m 30s
Soru 65Soru →

A uniform window-washing scaffold is 2020 feet long and weighs 180180 pounds. It is supported horizontally by two vertical cables, one attached at the extreme left end and one at the extreme right end. A worker weighing 220220 pounds stands exactly 55 feet from the left cable. If the system is in static equilibrium, what is the tension, in pounds, in the right cable?

Cevabı ve açıklamayı göster

Cevap: 145

Cevap

145
The system is in equilibrium, so the sum of the moments about the left support must be zero. The downward weights create a clockwise moment of 2900 lb-ft2900 \text{ lb-ft} (180 lbs×10 ft180 \text{ lbs} \times 10 \text{ ft} plus 220 lbs×5 ft220 \text{ lbs} \times 5 \text{ ft}). To balance this, the right cable, located 2020 feet away, must provide an equal counter-clockwise moment. Dividing 29002900 by 2020 yields a tension of 145145 pounds.

Adım Adım Çözüm

1
Select a pivot point to calculate moments (torques).
The left end of the scaffold is chosen as the pivot point.
Choosing the left end eliminates the unknown tension of the left cable from the equation, allowing direct calculation of the right cable's tension.
2
Calculate the total clockwise moment caused by the downward weights.
Scaffold moment = 180 lbs×10 ft=1800 lb-ft180 \text{ lbs} \times 10 \text{ ft} = 1800 \text{ lb-ft}. Worker moment = 220 lbs×5 ft=1100 lb-ft220 \text{ lbs} \times 5 \text{ ft} = 1100 \text{ lb-ft}. Total clockwise moment = 2900 lb-ft2900 \text{ lb-ft}.
The scaffold's weight acts at its center (1010 ft), and the worker's weight acts at 55 ft from the pivot. Moment equals force multiplied by distance.
3
Equate the clockwise moment to the counter-clockwise moment and solve.
TR×20 ft=2900 lb-ftT_R \times 20 \text{ ft} = 2900 \text{ lb-ft}, which gives TR=145 lbsT_R = 145 \text{ lbs}.
For the scaffold to be in static equilibrium, the sum of all moments about any pivot point must be zero.

Anahtar Kavram

Rotational equilibrium and calculation of moments (torque) to find support reaction forces.
Soru 66Soru →

A commercial box truck has a wheelbase (the distance between the front and rear axles) of 1515 feet. The empty truck weighs 6,0006,000 pounds, with its center of gravity located 66 feet behind the front axle. A 3,0003,000-pound industrial generator is loaded onto the truck and positioned directly above the rear axle. What is the total load supported by the rear axle in this configuration?

Cevabı ve açıklamayı göster

Cevap: 5,4005,400 pounds

Cevap

5,4005,400 pounds
To find the load on the rear axle, we must evaluate the contributions of the empty truck and the generator separately. For the empty truck, the center of gravity is 66 feet from the front axle, meaning it is closer to the front. Taking moments around the front axle, the rear axle supports 6/156/15 of the 6,0006,000-pound truck, which equals 2,4002,400 pounds. Because the 3,0003,000-pound generator is placed directly over the rear axle, its entire weight is added to that support. Adding both contributions together yields 2,400+3,000=5,4002,400 + 3,000 = 5,400 pounds.

Adım Adım Çözüm

1
Calculate the portion of the empty truck's weight supported by the rear axle.
Using the front axle as a pivot, the moment equation is: Rear Axle Force × 1515 ft = 6,0006,000 lbs × 66 ft. Solving for the force gives 36,000/15=2,40036,000 / 15 = 2,400 lbs.
The principle of moments dictates that the reaction force at a support is proportional to the distance of the load from the opposite support.
2
Determine the load added by the generator to the rear axle.
Since the 3,0003,000-lb generator is placed directly over the rear axle, 100%100\% of its weight rests on that axle (3,0003,000 lbs).
Loads placed directly on top of a support do not transfer any moment to the other supports.
3
Calculate the total weight supported by the rear axle.
2,400 lbs+3,000 lbs=5,400 lbs2,400\text{ lbs} + 3,000\text{ lbs} = 5,400\text{ lbs}.
The total load on a support is the sum of all individual load contributions.

Anahtar Kavram

Principle of Moments and Offset Load Distribution
Tahmini Süre:1m 15s
Soru 67Soru →

A uniform 1212-foot diving board weighing 5050 pounds is attached to a rear tie-down anchor at one end. The board rests on a fulcrum support located exactly 33 feet from the rear anchor. A 100100-pound swimmer stands at the extreme opposite end of the board. What is the required downward holding force (tension) at the rear tie-down anchor to keep the board horizontally balanced?

Cevabı ve açıklamayı göster

Cevap: 350350 pounds

Cevap

350350 pounds
To find the balancing force, we must ensure all rotational forces (torques) around the fulcrum cancel out. The swimmer (100100 lbs at a 99-foot distance from the fulcrum) creates 900900 lb-ft of torque. The board's center of gravity (5050 lbs at a 33-foot distance from the fulcrum) creates 150150 lb-ft of torque. The total clockwise torque is 10501050 lb-ft. Because the rear anchor is 33 feet from the fulcrum on the opposite side, it must pull down with a force of 1050÷3=3501050 \div 3 = 350 pounds to maintain equilibrium.

Adım Adım Çözüm

1
Identify the pivot point (fulcrum) and calculate the distances of all forces from this point.
The fulcrum is at 33 ft. The rear anchor is 33 ft away. The board's center of gravity is at 66 ft (33 ft from fulcrum). The swimmer is at 1212 ft (99 ft from fulcrum).
Torque is calculated by multiplying force by the distance to the fulcrum, not to the edge of the object.
2
Calculate the total clockwise torque caused by the board and the swimmer.
Board torque: 50 lbs×3 ft=150 lb-ft50 \text{ lbs} \times 3 \text{ ft} = 150 \text{ lb-ft}. Swimmer torque: 100 lbs×9 ft=900 lb-ft100 \text{ lbs} \times 9 \text{ ft} = 900 \text{ lb-ft}. Total clockwise torque = 1050 lb-ft1050 \text{ lb-ft}.
These forces push down on the right side of the fulcrum, acting to rotate the front of the diving board downward.
3
Determine the downward force required at the rear anchor to balance the system.
The rear anchor must provide an equal counter-clockwise torque. Force×3 ft=1050 lb-ft\text{Force} \times 3 \text{ ft} = 1050 \text{ lb-ft}. Force=10503=350 lbs\text{Force} = \frac{1050}{3} = 350 \text{ lbs}.
For static equilibrium, the opposing torques around the fulcrum must be equal.

Anahtar Kavram

Static Equilibrium and Torque
Soru 68Soru →

A heavy jet engine is suspended horizontally from a 1212-foot rigid lifting beam. The lifting beam is supported by two overhead hoists: Hoist 1 at the left end and Hoist 2 at the right end. Rank the following attachment points for the jet engine based on the tension load experienced by Hoist 1, from GREATEST to LEAST.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence from greatest to least load on Hoist 1 is: 33 feet from Hoist 1, 66 feet from Hoist 1, 99 feet from Hoist 1, and 1212 feet from Hoist 1.
In a simple beam supported at both ends, the load distributed to each support is directly proportional to how close the weight is to that support. The closer the jet engine is to Hoist 1, the more weight Hoist 1 must support. Therefore, arranging the attachment points from the shortest distance (33 feet) to the longest distance (1212 feet) correctly orders the load on Hoist 1 from greatest to least.

Adım Adım Çözüm

1
Identify the relationship between load position and support reaction forces in a static beam system.
The closer a load is to a specific support point, the greater the proportion of the weight that support must carry.
This is a fundamental principle of lever mechanics and load distribution.
2
Determine the relative distances of each attachment point from Hoist 1.
The distances are 33 feet, 66 feet, 99 feet, and 1212 feet.
Establishing the distances allows for direct comparison of the load distribution.
3
Order the distances from shortest to longest to rank the load from greatest to least.
Shortest distance (33 ft) creates the greatest load on Hoist 1, followed by 66 ft, 99 ft, and the longest distance (1212 ft) creates the least load.
Because the load on a support is inversely proportional to the load's distance from that support.

Anahtar Kavram

The proportion of a load carried by a support is inversely related to the distance between the center of gravity of the load and that support.
Tahmini Süre:1m 0s
Soru 69Soru →

An irregularly shaped 300300-pound machine casing is 1010 feet long. For maintenance, it is suspended horizontally by two vertical chains, one attached at the extreme left end and one at the extreme right end. The casing's center of gravity is located 22 feet from the left end.

How much weight is supported by the right chain?

Cevabı ve açıklamayı göster

Cevap: 6060 pounds

Cevap

6060 pounds
Because the center of gravity is offset, the weight is not distributed equally. By using the left end as a pivot point, we can balance the torques. The weight of the casing creates a downward torque of 300 lbs×2 ft=600 ft-lbs300 \text{ lbs} \times 2 \text{ ft} = 600 \text{ ft-lbs}. The right chain, pulling upward at a distance of 1010 feet, must create an equal opposite torque. Therefore, Fright×10 ft=600 ft-lbsF_{right} \times 10 \text{ ft} = 600 \text{ ft-lbs}, which means the right chain supports 6060 pounds.

Adım Adım Çözüm

1
Choose a pivot point to set up a torque equation.
Using the left end (where the left chain is attached) as the pivot eliminates the left chain's unknown force from the calculation.
In static equilibrium, the sum of torques around any point must be zero. Choosing one support as the pivot makes it easier to solve for the other support.
2
Calculate the downward torque generated by the casing's weight.
The downward torque is the weight (300300 pounds) multiplied by its distance from the left pivot (22 feet): 300×2=600300 \times 2 = 600 foot-pounds.
Torque is Force multiplied by Distance from the fulcrum.
3
Set the downward torque equal to the upward torque generated by the right chain and solve.
The upward torque is the unknown force of the right chain (FrightF_{right}) multiplied by its distance from the pivot (1010 feet). So, Fright×10=600F_{right} \times 10 = 600. Dividing both sides by 1010 gives Fright=60F_{right} = 60 pounds.
Upward torque must equal downward torque for the casing to remain balanced horizontally.

Anahtar Kavram

Load Distribution and Balancing
Tahmini Süre:1m 0s
Soru 70Soru →

During a routine weight and balance check, a small aircraft is parked horizontally on weighing scales. The scale under the nose wheel reads 500500 pounds, and the combined reading from the scales under the two main wheels is 1,5001,500 pounds. The nose wheel is located exactly 100100 inches forward of the main landing gear axis. How many inches forward of the main landing gear axis is the aircraft's center of gravity?

Cevabı ve açıklamayı göster

Cevap: 25

Cevap

25
In static equilibrium, the sum of the moments around any point must be zero. By using the main landing gear axis as the reference point, the moment created by the total weight of the aircraft (2,0002,000 pounds) acting at the center of gravity must equal the moment created by the nose wheel's load. The nose wheel is 100100 inches away and supports 500500 pounds, creating a moment of 50,00050,000 pound-inches. Dividing this total moment by the total weight (50,000÷2,00050,000 \div 2,000) gives a center of gravity located 2525 inches forward of the main gear.

Adım Adım Çözüm

1
Determine the total weight of the aircraft.
500+1,500=2,000500 + 1,500 = 2,000 pounds
The total weight is needed to find the proportion of the load carried by each support.
2
Set up the balance equation (sum of moments) around the main landing gear axis.
(Total Weight)×(CG Distance)=(Nose Wheel Weight)×(Distance to Nose Wheel)(Total\ Weight) \times (CG\ Distance) = (Nose\ Wheel\ Weight) \times (Distance\ to\ Nose\ Wheel)
In static equilibrium, the moment generated by the total weight at the CG equals the sum of the moments of individual components.
3
Substitute the known values into the equation and solve for the CG distance.
2,000×d=500×100⇒2,000d=50,000⇒d=252,000 \times d = 500 \times 100 \Rightarrow 2,000d = 50,000 \Rightarrow d = 25 inches
Solving the algebraic equation isolates the distance from the main gear to the center of gravity.

Anahtar Kavram

Center of Gravity and Static Equilibrium

Alternatif Yöntem

Instead of using the main gear as the pivot, you can use the nose wheel as the pivot. The moment of the main gear is 1,500×100=150,0001,500 \times 100 = 150,000. Dividing by the total weight (2,0002,000) gives 7575 inches from the nose wheel. Subtracting this from the total wheelbase (100−75100 - 75) gives 2525 inches from the main gear.
Tahmini Süre:1m 0s
Soru 71Soru →

A single-axle utility trailer has a total loaded weight of 2,0002,000 pounds. The loaded trailer's center of gravity is located 33 feet forward of the axle. If the trailer hitch is located 1212 feet forward of the axle, what is the downward force exerted on the hitch when the trailer is horizontally parked?

Cevabı ve açıklamayı göster

Cevap: 500500 pounds

Cevap

500500 pounds
In static equilibrium, the sum of torques around any pivot point must be zero. By treating the axle as the pivot, the weight of the trailer (2,0002,000 pounds) acts at a distance of 33 feet from the pivot, creating a torque of 6,0006,000 ft-lbs. To balance this, the upward force from the hitch (located 1212 feet away) must equal 6,0006,000 ft-lbs divided by 1212 feet, which yields 500500 pounds.

Adım Adım Çözüm

1
Identify the pivot point and the forces acting on the system.
The axle acts as the pivot point (fulcrum). The two forces creating torque around the axle are the trailer's weight (2,0002,000 lbs) pushing down at the center of gravity, and the hitch support pushing up.
Setting the axle as the pivot eliminates its unknown support force from the initial torque equation.
2
Calculate the torque (moment) created by the trailer's weight around the axle.
Torque = Force × Distance = 2,000 lbs×3 ft=6,000 lb-ft2,000\text{ lbs} \times 3\text{ ft} = 6,000\text{ lb-ft}.
This is the rotational force that the hitch must counterbalance to keep the trailer horizontal.
3
Set up the equilibrium equation to solve for the force at the hitch.
Fhitch×12 ft=6,000 lb-ftF_{\text{hitch}} \times 12\text{ ft} = 6,000\text{ lb-ft}.
In static equilibrium, the clockwise torque must equal the counterclockwise torque.
4
Solve for the hitch force.
Fhitch=6,000÷12=500 poundsF_{\text{hitch}} = 6,000 \div 12 = 500\text{ pounds}.
Dividing the required balancing torque by the lever arm distance gives the necessary support force.

Anahtar Kavram

Static Equilibrium and Torque (Moments)
Soru 72Soru →

Two workers, Worker X and Worker Y, are carrying a heavy motor block using a rigid, 1212-foot wooden beam. Each worker supports one end of the beam on their shoulder. The motor block weighs 300300 pounds. Assume the weight of the beam is negligible. If the center of the motor block is placed on the beam exactly 33 feet away from Worker X, how much of the block's weight is Worker Y supporting?

Cevabı ve açıklamayı göster

Cevap: 7575 pounds

Cevap

Worker Y is supporting 7575 pounds of the motor block's weight.
The system is in static equilibrium. By setting Worker X as the pivot point (fulcrum), the motor block creates a downward torque of 300 pounds×3 feet=900 foot-pounds300 \text{ pounds} \times 3 \text{ feet} = 900 \text{ foot-pounds}. To keep the beam from rotating, Worker Y must exert an equal opposing torque at a distance of 1212 feet (the entire length of the beam). Therefore, Worker Y's force is 900÷12=75 pounds900 \div 12 = 75 \text{ pounds}. Because Worker Y is four times further from the load than Worker X is, Worker Y carries one-fourth of the weight.

Adım Adım Çözüm

1
Identify the pivot point and the forces acting on the beam.
Let Worker X's shoulder be the pivot point. The forces are the 300300-pound downward load acting at a distance of 33 feet, and Worker Y's upward supporting force acting at a distance of 1212 feet.
Setting one end as the pivot point allows us to isolate the unknown force at the other end using the principle of torque (moments).
2
Set up the static equilibrium equation where total torque equals zero.
The downward torque from the block must equal the upward torque from Worker Y: 300×3=FY×12300 \times 3 = F_Y \times 12.
For the beam to be balanced and not rotate, the clockwise moments and counter-clockwise moments around the pivot must be equal.
3
Solve the equation for Worker Y's supporting force (FYF_Y).
900=12×FY900 = 12 \times F_Y, which simplifies to FY=900/12=75F_Y = 900 / 12 = 75 pounds.
Basic algebra is used to isolate the unknown variable.

Anahtar Kavram

Load distribution and static equilibrium (torques/moments)
Soru 73Soru →

Four different vehicles each have a total loaded weight of 6,0006,000 pounds. Arrange the following vehicles in order based on the amount of weight supported by their REAR axle, from greatest weight to least weight.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct order from greatest to least rear axle load is: Delivery van (4,0004,000 lbs), Pickup truck (3,5003,500 lbs), Flatbed truck (3,0003,000 lbs), and Box truck (1,5001,500 lbs).
To find the load on the rear axle, the vehicle is treated as a beam where the front axle acts as the pivot (fulcrum). The rear axle load is found by taking the proportion of the center of gravity's distance from the front axle relative to the entire wheelbase, and multiplying by the total weight. The delivery van has the highest proportion (1015=66.7%\frac{10}{15} = 66.7\%), followed by the pickup truck (712=58.3%\frac{7}{12} = 58.3\%), flatbed truck (714=50%\frac{7}{14} = 50\%), and box truck (416=25%\frac{4}{16} = 25\%).

Adım Adım Çözüm

1
Determine the formula for load distribution on the rear axle.
Rear Axle Load = Total Weight×(Distance from Front AxleWheelbase)\text{Total Weight} \times (\frac{\text{Distance from Front Axle}}{\text{Wheelbase}})
The vehicle acts as a beam supported at both ends (the axles). The load on the rear support is directly proportional to how far the center of gravity is from the front support.
2
Calculate the rear axle load for the delivery van.
6,000 lbs×(10 ft15 ft)=6,000×23=4,000 lbs6,000\text{ lbs} \times (\frac{10\text{ ft}}{15\text{ ft}}) = 6,000 \times \frac{2}{3} = 4,000\text{ lbs}.
The center of gravity is explicitly given as 1010 feet behind the front axle.
3
Calculate the rear axle load for the pickup truck.
Distance from front = 12 ft−5 ft=7 ft12\text{ ft} - 5\text{ ft} = 7\text{ ft}. Load = 6,000 lbs×(7 ft12 ft)=3,500 lbs6,000\text{ lbs} \times (\frac{7\text{ ft}}{12\text{ ft}}) = 3,500\text{ lbs}.
The center of gravity is 55 feet forward of the rear axle, meaning it is 77 feet behind the front axle.
4
Calculate the rear axle load for the flatbed truck.
6,000 lbs×(7 ft14 ft)=6,000×12=3,000 lbs6,000\text{ lbs} \times (\frac{7\text{ ft}}{14\text{ ft}}) = 6,000 \times \frac{1}{2} = 3,000\text{ lbs}.
The center of gravity is 77 feet behind the front axle, exactly in the middle of the 1414-foot wheelbase.
5
Calculate the rear axle load for the box truck.
Distance from front = 16 ft−12 ft=4 ft16\text{ ft} - 12\text{ ft} = 4\text{ ft}. Load = 6,000 lbs×(4 ft16 ft)=1,500 lbs6,000\text{ lbs} \times (\frac{4\text{ ft}}{16\text{ ft}}) = 1,500\text{ lbs}.
The center of gravity is 1212 feet forward of the rear axle, meaning it is 44 feet behind the front axle.
6
Arrange the vehicles based on the calculated loads.
Delivery van (4,0004,000 lbs) > Pickup truck (3,5003,500 lbs) > Flatbed truck (3,0003,000 lbs) > Box truck (1,5001,500 lbs).
The question asks for the order from greatest weight to least weight supported by the rear axle.

Anahtar Kavram

Load distribution on a beam with two supports (axles) is inversely proportional to the distance from the center of gravity to each support.

Alternatif Yöntem

You can calculate the weight on the front axle first by using the distance to the rear axle divided by the total wheelbase, then subtract that front axle load from the 6,0006,000 lbs total weight to find the rear axle load.
Tahmini Süre:1m 30s
Soru 74Soru →

Why are highly hardened steel bolts typically avoided in mechanical applications subjected to heavy shock loads and constant vibrations, such as automotive suspension systems?

Cevabı ve açıklamayı göster

Cevap: Extremely hard materials tend to be brittle and can suddenly fracture when subjected to high-impact forces.

Cevap

Extremely hard materials tend to be brittle and can suddenly fracture when subjected to high-impact forces.
The correct answer accurately identifies the trade-off between hardness and brittleness. While hardened steel resists wear and static loads very well, it lacks the toughness required to absorb sudden kinetic energy. Instead of yielding slightly under a severe shock, a fully hardened bolt will snap, which is a catastrophic failure in an automotive suspension.

Adım Adım Çözüm

1
Analyze the mechanical requirements of the scenario.
Automotive suspension systems experience heavy shock loads and constant vibrations.
Identifying the applied forces helps determine which material properties are most critical for the component to survive.
2
Evaluate the material property in question (Hardness).
Hardness is a material's resistance to localized deformation, such as scratching or indentation. However, as steel is hardened, it typically loses its toughness and ductility.
Understanding the trade-offs of material treatments is essential for engineering component selection.
3
Relate the material property trade-offs to the required application.
Because hardened steel is brittle, a sudden shock from the suspension could exceed its ultimate tensile strength without any prior stretching, causing the bolt to snap catastrophically. Therefore, a moderately hard but tougher bolt is preferred.
Components in shock-loading environments must be able to absorb energy (toughness) rather than strictly resisting deformation.

Anahtar Kavram

Material Toughness vs. Brittleness
Tahmini Süre:1m 0s
Soru 75Soru →

An engineering team evaluates different metal alloys by observing their reactions to specific mechanical stresses during laboratory testing. Match each observed behavior to the specific material property it demonstrates.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Öğeler

Ductility
Malleability
Elasticity
Brittleness

Eşleşmeler

Cevabı ve açıklamayı göster

Cevap

Ductility pairs with elongating under tensile stress; Malleability pairs with deforming into sheets under compressive loads; Elasticity pairs with returning to original dimensions; and Brittleness pairs with sudden fracture under impact.
Each pairing correctly aligns a fundamental mechanical property with its standard engineering definition. Ductility governs tension, malleability governs compression, elasticity governs temporary restorative deformation, and brittleness dictates failure under sudden impact.

Adım Adım Çözüm

1
Analyze the behavior involving elongation and tensile stress.
This behavior maps to Ductility.
Ductility is exclusively defined by how well a material can be drawn out (stretched) under tension without breaking.
2
Analyze the behavior involving deformation into thin sheets under compressive loads.
This behavior maps to Malleability.
Malleability dictates how a material responds to compression, such as being pressed or hammered into flat sheets.
3
Analyze the behavior involving returning to original dimensions after bending.
This behavior maps to Elasticity.
Elasticity is the tendency of solid materials to return to their original shape after being deformed.
4
Analyze the behavior involving sudden fracture under sharp impact.
This behavior maps to Brittleness.
Brittleness is the opposite of toughness and ductility; brittle materials fail suddenly with negligible plastic yielding when subjected to shock.

Anahtar Kavram

Material behavior under distinct mechanical stresses (tension, compression, impact, and bending).
Soru 76Soru →

During the assembly of a metal aircraft framework, a technician uses a pneumatic hammer to strike the unheaded end of a solid metal rivet. The repeated impacts successfully flatten the end of the cylinder to form a permanent locking head without cracking or splintering the material. Which material property primarily allows the rivet to undergo this permanent deformation under compressive force?

Cevabı ve açıklamayı göster

Cevap: Malleability

Cevap

The correct property is malleability.
Malleability is the physical property that allows a solid to bend or be hammered into other shapes without breaking. Because the pneumatic hammer applies compressive stress to flatten the rivet, malleability is the exact property required for this process.

Adım Adım Çözüm

1
Identify the type of force being applied in the scenario.
The pneumatic hammer applies a crushing, compressive force to the rivet.
Different material properties govern how a substance reacts to different types of applied forces (e.g., tension vs. compression).
2
Analyze the required outcome of the deformation.
The rivet must flatten into a new shape permanently (plastic deformation) without breaking or cracking.
If the deformation were temporary, the rivet would not lock the joint. If the material fractured, the joint would fail.
3
Match the observed behavior to the corresponding material property definitions.
The ability to deform plastically under compressive stress without fracturing defines malleability.
This distinguishes it from ductility (tensile stress) and elasticity (temporary deformation).

Anahtar Kavram

Malleability vs. other structural material properties
Tahmini Süre:1m 0s
Soru 77Soru →

A structural material that possesses exceptionally high compressive strength will inherently exhibit an equally high tensile strength when subjected to pulling forces.

Cevabı ve açıklamayı göster

Cevap: False

Cevap

False
The statement is false because the ability of a material to withstand being crushed (compressive strength) does not guarantee its ability to withstand being stretched (tensile strength). Concrete and cast iron are classic examples of materials that are extremely strong in compression but weak in tension.

Adım Adım Çözüm

1
Define the terms compressive strength and tensile strength in the context of structural materials.
Compressive strength is a material's resistance to being crushed or pushed together, while tensile strength is its resistance to being stretched or pulled apart.
Clarifying the specific definitions of these forces is necessary to evaluate how materials respond to them.
2
Evaluate the claim that high performance in compression guarantees equally high performance in tension.
Determine that the claim is false by recalling common real-world structural materials that behave asymmetrically.
Identifying valid counterexamples, such as concrete (which requires steel rebar specifically to compensate for its poor tensile strength), proves that the two properties are not inherently linked.

Anahtar Kavram

Compressive vs. Tensile Strength
ÖncekiSayfa 4 / 4
Structural Support and Materials Alıştırma Soruları — Armed Services Vocational Aptitude Battery (ASVAB) — Sayfa 4 | Examkin