Examkin

Inferences and Conclusions

206 soru

Tüm türler206Çoktan seçmeli105Doğru / Yanlış61Eşleştirme21Sıralama3Boşluk doldurma16
Soru 201Soru →

Read the passage below. Based on the directional and sensor evidence provided, what is the logical conclusion regarding the location of the vent? Fill in the blank to complete the deduction.

Aşağıdaki boşlukları doldurun

Deep-sea thermal loggers recorded anomalous temperature spikes at an abyssal survey site only when hydrothermal vents discharged heated fluids. Whenever bottom currents shifted westward, Eastern Sensor Array detected no thermal deviation, while Western Sensor Array registered immediate temperature increases exceeding eight degrees Celsius. Given that thermal plumes travel exclusively downstream with local currents, researchers deduced that the active hydrothermal vent must be located directly of the Western Sensor Array.
Cevabı ve açıklamayı göster

Cevap

east (or upstream)
The passage specifies that thermal plumes move strictly downstream with local currents. When bottom currents travel westward, the fluid flows from east to west. Because the Western Sensor Array detects the plume under these exact conditions, the sensor must be downstream of the source, meaning the active vent must be located upstream, directly to the east of the Western Sensor Array.

Adım Adım Çözüm

1
Identify the direction of transport and the behavior of the fluid plume.
The text states that the thermal plume moves exclusively downstream with the local current, which flows westward (from east to west).
Establishing the physical transport mechanism is required to link the source to the detector.
2
Analyze the sensor detection pattern under the westward current condition.
The Western Sensor Array detected significant temperature increases during westward current flow, while the Eastern Sensor Array detected nothing.
This confirms that the Western Sensor Array sits downstream of the active discharge during westward transport.
3
Deduce the relative spatial origin of the plume.
Because the plume moves westward to reach the Western Sensor Array, the origin of the plume must be situated upstream, directly to the east of the Western Sensor Array.
A source must be upstream (east) of a downstream sensor (west) for westward flow to carry the fluid to that sensor.

Anahtar Kavram

Synthesizing directional flow constraints and sensor detection data to deduce an unstated spatial origin.
Tahmini Süre:1m 30s
Soru 202Soru →

Technicians in the motor pool parked several diesel transport trucks outside overnight in sub-zero temperatures. The following morning, the drivers turned the ignition keys, but the engines cranked sluggishly and failed to start. After the maintenance crew wheeled portable heaters into the staging bay and directed warm air onto the fuel tanks and engine blocks for thirty minutes, each vehicle started on the first attempt.

What most likely caused the trucks' initial failure to start?

Cevabı ve açıklamayı göster

Cevap: The prolonged exposure to freezing overnight temperatures

Cevap

The prolonged exposure to freezing overnight temperatures
The passage describes trucks failing to start after exposure to sub-zero temperatures and functioning normally once warmed. This sequence logically implies that the freezing conditions caused the starting failure.

Adım Adım Çözüm

1
Identify the initial condition and subsequent problem in the scenario.
The trucks were left outside in sub-zero weather and failed to start the next morning.
Recognizing the starting state provides the context for evaluating what led to the malfunction.
2
Examine the intervention and the resulting outcome.
Applying warm air to the engines enabled them to start on the first attempt.
Identifying what cured the problem reveals the unstated root cause.
3
Deduce the implied causal relationship between temperature and engine performance.
Because heating reversed the failure, the extreme cold was the underlying cause.
Connecting the cold environment to the successful heat remedy confirms the implied cause.

Anahtar Kavram

Recognizing Implied Cause and Effect
Tahmini Süre:45s
Soru 203Soru →

A machinist shaping a precision titanium valve noticed irregular grooves forming along the milled edges of the part. Earlier that morning, the workshop's central coolant pump had experienced a pressure drop, reducing the stream of fluid delivered to the cutting head. Upon inspecting the carbide tool immediately afterward, the machinist observed severe blunting on its contact edge.

What most likely led to the irregular grooves on the titanium valve?

Cevabı ve açıklamayı göster

Cevap: A blunted cutting tool operating with diminished fluid lubrication

Cevap

A blunted cutting tool operating with diminished fluid lubrication
The passage establishes that the coolant pump lost pressure, decreasing fluid delivery to the cutting head, and that the carbide tool became severely blunted. Logically connecting these events reveals that insufficient lubrication degraded the tool's cutting edge, which directly created the irregular grooves on the valve.

Adım Adım Çözüm

1
Identify the primary problem described in the passage
The finished titanium valve has irregular grooves along its milled edges.
Establishing the specific outcome helps pinpoint the contributing factors mentioned in the text.
2
Trace the sequence of physical conditions leading up to the defect
The coolant pump pressure dropped, fluid delivery to the cutting head decreased, and the carbide tool suffered severe edge blunting.
Analyzing the chronological sequence reveals the unstated mechanical relationship between reduced lubrication, accelerated tool wear, and poor cut quality.
3
Synthesize the implied cause-and-effect relationship
The lack of adequate coolant caused the tool to blunt, which produced the uneven grooves on the workpiece.
Connecting these facts logically identifies the true root cause without relying on explicit transitional words.

Anahtar Kavram

Recognizing Implied Cause and Effect
Tahmini Süre:1m 0s
Soru 204Soru →

Passage:
Prior to performing maintenance on industrial hydrocarbon lines, operators purge the piping with pressurized nitrogen gas rather than atmospheric air. Because hydrocarbons combust only within a specific fuel-to-oxygen ratio, displacing oxygen with chemically inert nitrogen prevents flammable mixtures from forming, even if residual volatile vapors remain inside the conduit. Once the purge is complete, sensors verify that oxygen levels remain below dangerous thresholds before cutting or welding begins.

Statement: Hot maintenance such as welding can proceed safely on purged lines even if volatile hydrocarbon vapors are still present inside the piping.

Cevabı ve açıklamayı göster

Cevap: True

Cevap

True
The author explains that fire requires a specific fuel-to-oxygen mixture and that inert nitrogen prevents combustion even if volatile vapors remain. This directly implies that welding is safe despite residual fuel vapors as long as oxygen remains below hazardous thresholds.

Adım Adım Çözüm

1
Identify the conditions necessary for hydrocarbon combustion stated in the passage.
Combustion requires both hydrocarbon fuel and oxygen present within a specific ratio.
Understanding the combustion requirement establishes why oxygen displacement is the critical safety factor.
2
Deduce the effect of nitrogen purging on the danger posed by residual vapors.
Since inert nitrogen displaces oxygen, fuel vapors cannot reach a combustible ratio and therefore cannot ignite.
This clarifies that total eradication of fuel vapors is unnecessary for safety as long as oxygen is sufficiently eliminated.
3
Evaluate the statement against the implied textual evidence.
The statement correctly reflects the implied principle that residual fuel vapors do not present an ignition hazard when oxygen is absent.
Confirms that the statement is logically valid based on the text.

Anahtar Kavram

Deducing unstated physical implications from stated operational relationships in a technical passage.
Tahmini Süre:1m 0s
Soru 205Soru →

Read the following passage:

High-altitude transport aircraft utilize regulated bleed air from turbine engines to maintain positive pressure inside hydraulic fluid reservoirs. At cruising altitudes above 30,000 feet, low ambient atmospheric pressure decreases the boiling point of hydraulic fluid and reduces the inlet pressure delivered to engine-driven pumps. Without artificial reservoir pressurization, fluid vaporization and destructive cavitation occur within pump chambers during operation.

Statement: Without supplemental reservoir pressurization, ambient atmospheric pressure at high cruising altitudes is inadequate to prevent hydraulic fluid from boiling and damaging the pumps.

Cevabı ve açıklamayı göster

Cevap: True

Cevap

True: Ambient atmospheric pressure at cruising altitude is insufficient on its own to keep hydraulic fluid below its boiling point and prevent cavitation without bleed-air pressurization.
The conclusion directly follows from combining two core premises in the text: at cruising altitude, ambient pressure lowers the boiling point of fluid, and omitting supplemental pressurization results in vaporization and cavitation.

Adım Adım Çözüm

1
Identify the environmental constraints and operational hazards presented in the text.
Cruising altitudes above 30,000 feet feature low ambient atmospheric pressure, which decreases the hydraulic fluid's boiling point and lowers pump inlet pressure.
Understanding the baseline physical environment is necessary to evaluate why normal atmospheric conditions are insufficient.
2
Determine the role of artificial reservoir pressurization relative to these hazards.
Regulated bleed air provides artificial pressurization to prevent the vaporization and destructive pump cavitation that would otherwise happen.
Establishing the function of the pressurization system clarifies what occurs when it is absent.
3
Synthesize the facts to deduce whether natural ambient pressure alone can maintain safe operating conditions.
Natural atmospheric pressure at high altitudes is demonstrably insufficient, making the evaluated statement strictly true.
Connecting the lack of adequate ambient pressure to the necessity of artificial pressurization validates the logical conclusion.

Anahtar Kavram

Drawing Logical Deductions from Multi-Condition Technical Relationships
Soru 206Soru →

Early steam locomotives relied on mechanical governors to regulate engine speed under varying track loads. In a typical centrifugal governor, two weighted brass spheres spin on a central spindle driven directly by the locomotive's drive axle. As engine velocity increases, centrifugal force drives the spheres outward and upward against gravity, mechanically linkage-closing the throttle valve to reduce steam intake. Conversely, when the locomotive encounters an incline and slows down, the spheres drop inward, opening the valve to admit more steam. This mechanical feedback loop allowed operators to maintain steady boiler efficiency and prevent catastrophic wheel slippage without requiring continuous manual throttle adjustments.

Which of the following best describes the author's primary purpose in writing this passage?

Cevabı ve açıklamayı göster

Cevap: explain how an automatic feedback mechanism regulates locomotive engine speed

Cevap

The author's primary purpose is to explain how an automatic feedback mechanism regulates locomotive engine speed.
The author systematically outlines the physical components of the centrifugal governor and explains the mechanical process through which rotating spheres adjust the throttle valve during speed changes. Because the entire passage is structured around clarifying how this self-regulating loop operates, the primary intent is to explain the functioning of this automated speed-regulation mechanism.

Adım Adım Çözüm

1
Analyze the main focus and structure of the passage
The text describes the physical components of a centrifugal governor (spindle, brass spheres, throttle linkage) and traces the physical cause-and-effect cycle that adjusts steam intake based on travel speed.
Examining the dominant content and logical organization reveals why the author composed the paragraph.
2
Determine the author's tone and rhetorical function
The passage maintains a neutral, expository tone aimed at describing how a device functions rather than persuading, warning, or criticizing.
Recognizing the expository nature of the writing distinguishes purely explanatory passages from argumentative or cautionary texts.
3
Synthesize the overarching communicative goal
The author's central aim is to inform the reader about how an automated mechanical feedback loop controls steam engine velocity under changing operating conditions.
The correct response must reflect the passage as a cohesive whole rather than an isolated detail or an unsupported inference.

Anahtar Kavram

Inferring author purpose through synthesis of main idea, rhetorical structure, and objective tone.
Tahmini Süre:1m 0s
ÖncekiSayfa 11 / 11
Inferences and Conclusions Alıştırma Soruları — Armed Services Vocational Aptitude Battery (ASVAB) — Sayfa 11 | Examkin