Examkin

NTP Client and Server Operations and Configuration

15 soru

Tüm türler15Çoktan seçmeli7Çoklu seçim4Sıralama4
Soru 1Soru →

A network administrator configures a Cisco IOS router to synchronize its internal clock with an enterprise NTP server operating at Stratum 2. Arrange the operational steps in chronological order from initial packet transmission to the point where the router can act as a valid time source for downstream clients.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence of operations is: 1) The router sends an NTP client mode query (UDP port 123) to the server. 2) The router receives an NTP server mode response with Stratum 2 metadata. 3) The router computes round-trip delay, dispersion, and clock offset algorithms. 4) The router synchronizes its system clock and increments its operational stratum to Stratum 3. 5) The router begins answering incoming NTP queries from downstream clients.
NTP synchronization follows a strict sequential process: outbound UDP 123 request initiation, receipt of server time payload and stratum attributes, statistical filtering of offset and round-trip delay, local clock adjustment accompanied by stratum incrementing (N+1N+1), and finally responding to downstream client requests as a synchronized master time source.

Adım Adım Çözüm

1
Initiate communication
Router sends an outbound NTP client packet over UDP port 123 to the NTP server address.
Synchronization starts when the client polls the server for time information.
2
Receive server response
Server replies with timestamp, stratum level (Stratum 2), and reference clock identification.
The server must supply its current time and stratum attributes back to the client.
3
Process NTP statistical filtering
Router calculates offset and network delay while filtering out jitter and invalid timestamps.
Packet delay and clock drift must be calculated before modifying the local system time.
4
Update local system time and stratum
Local clock synchronizes, and local stratum becomes Stratum 3 (2+12 + 1).
A synchronized NTP device always assumes a stratum number one unit higher than its synchronization source.
5
Serve downstream clients
Router processes and responds to NTP requests from local hosts.
Downstream devices can only receive valid, synchronized time after the router completes synchronization and establishes a valid stratum (< 16).

Anahtar Kavram

NTP Client-Server Initialization Sequence and Stratum Calculation
Soru 2Soru →

A network router is configured with the global configuration command `ntp master 6`. Additionally, the router has a configured association using `ntp server 172.16.40.10`. The remote NTP server at IP address 172.16.40.10172.16.40.10 is reachable and currently operates at Stratum 3. Assuming time synchronization between the router and the remote server succeeds, what stratum level will this router advertise to its downstream NTP clients?

Cevabı ve açıklamayı göster

Cevap: Stratum 4

Cevap

The router will operate at and advertise Stratum 4 because it adds 1 to the stratum level of its active upstream reference source (Stratum 3).
In Network Time Protocol (NTP), stratum levels represent the distance from an authoritative reference clock (Stratum 0). When a router synchronizes with an NTP server at Stratum NN, the router's calculated stratum level becomes N+1N + 1. Since the upstream server is at Stratum 3, the router synchronizes to it and operates at Stratum 4. The `ntp master [stratum]` command configures the router as a master NTP server using its own internal clock only if external NTP sources fail or are unreachable.

Adım Adım Çözüm

1
Determine the active NTP source
The router has an active, reachable NTP server at 172.16.40.10 operating at Stratum 3.
An active external NTP server association takes precedence over the internal `ntp master` fallback command.
2
Calculate the local router's stratum level
Stratum level = Upstream Stratum + 1 = 3 + 1 = 4.
NTP stratum levels increment by 1 for each hop away from the authoritative reference clock (Stratum 0).

Anahtar Kavram

NTP Stratum Calculation and Fallback Master Precedence
Soru 3Soru →

A network administrator configures a Cisco IOS router to synchronize its time with an upstream NTP server operating at Stratum 2. Arrange the following steps in the correct chronological order from the initial synchronization attempt to successful time synchronization on the router.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence starts with transmitting the NTP request packet (UDP 123), followed by receiving the server response with Stratum 2 details, calculating offset and delay, updating the local clock to Stratum 3, and finally marking the peer association as synchronized (∗*).
The NTP synchronization process must follow a logical operational sequence: first, sending a client poll via UDP port 123; second, receiving the server's timestamp and Stratum 2 payload; third, computing time drift and transit delay; fourth, adjusting the local clock and incrementing stratum to 3; and fifth, marking the verified peer as synchronized (∗*) in system output.

Adım Adım Çözüm

1
Initiate NTP request
The router sends a client mode NTP packet on UDP port 123.
Synchronization begins when the client actively polls the configured NTP server.
2
Receive server payload
The server sends back an NTP packet indicating Stratum 2 and authoritative timestamp info.
The server provides the reference time data needed for calculation.
3
Compute clock offset and network delay
The router uses the four timestamps (origin, receive, transmit, destination) to determine offset.
Transit delay must be accounted for to accurately adjust the local clock.
4
Adjust system time and increment stratum
System clock is synchronized and stratum becomes 3 (2+12 + 1).
An NTP client's stratum is defined as the server's stratum plus one hop distance.
5
Flag active system peer
The peer displays an asterisk (∗*) in `show ntp associations`.
The asterisk denotes the configured NTP source currently selected for system clock synchronization.

Anahtar Kavram

NTP Client-Server Synchronization Sequence and Stratum Hierarchy Propagation
Soru 4Soru →

An enterprise core router is designated to act as both an NTP client to an upstream stratum 2 server and an NTP server for internal distribution switches. To ensure reliable operations and consistent packet parameters, the network engineer must force the router to send NTP packets using a specific logical interface address and allow the router to serve as an authoritative time source if the upstream connection becomes unavailable. Which TWO Cisco IOS global configuration commands satisfy these requirements?

Geçerli olan tümünü seçin

Cevabı ve açıklamayı göster

Cevap: ntp source Loopback0; ntp master 5

Cevap

The correct commands are 'ntp source Loopback0' and 'ntp master 5'.
Configuring 'ntp source Loopback0' ensures all outbound NTP control packets carry the loopback IP address as their source address, which aids access list matching and system stability. Configuring 'ntp master 5' allows the router to serve as a backup NTP server to downstream peers/clients at Stratum 5 when upstream synchronization fails.

Adım Adım Çözüm

1
Identify the requirement for specifying the NTP packet source address.
The global configuration command 'ntp source <interface>' ensures NTP request/response packets use a stable IP address.
Loopback interfaces remain up as long as the router is powered, providing a consistent source IP for network management and security control.
2
Identify the requirement for providing fallback authoritative time synchronization.
The global configuration command 'ntp master [stratum]' enables the internal hardware clock to act as an NTP server.
Setting 'ntp master 5' allows downstream clients to synchronize with this device at stratum 5 if connection to the primary stratum 2 server is lost.

Anahtar Kavram

NTP Source Interface and Master Clock Fallback Configuration
Soru 5Soru →

A network administrator is configuring a Cisco IOS router to synchronize its clock with a remote time server located at IP address 192.168.10.5. The router must operate strictly in client mode, polling time from the specified server without allowing the remote device to synchronize to the local router clock. Which global configuration command meets this requirement?

Cevabı ve açıklamayı göster

Cevap: ntp server 192.168.10.5

Cevap

The command 'ntp server 192.168.10.5' configures the router to operate in NTP client mode toward the target server.
The global configuration command 'ntp server 192.168.10.5' configures the router as an NTP client to the target remote NTP server. In client mode, the local device receives time updates from the specified server but will not allow the server to synchronize to the local system clock.

Adım Adım Çözüm

1
Identify the required NTP association mode
The requirement specifies a client-server relationship where the local device polls time from the remote server without providing time to it.
NTP supports client/server, peer, and master modes.
2
Select the corresponding Cisco IOS global configuration syntax
The command 'ntp server <ip-address>' establishes a client-to-server NTP association.
'ntp peer' creates a symmetric active partnership, while 'ntp master' enables local authoritative master clock operation.

Anahtar Kavram

NTP Client vs Peer Mode Configuration
Soru 6Soru →

A network administrator is configuring time synchronization on a newly installed Cisco IOS router. Arrange the following operational events in the correct chronological order, from initial CLI configuration to serving downstream clients.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct operational sequence is: 1) Executing `ntp server 10.1.1.50` on the router, 2) Exchanging NTP polling messages to calculate delay and offset, 3) Adjusting the local system clock, 4) Transitioning to a synchronized state at Stratum 3 (upstream + 1), and 5) Responding to downstream client requests at Stratum 3.
The NTP operation sequence begins with establishing the peer/server relationship via `ntp server`. Polling packets are then exchanged to calculate offset and dispersion. Once metrics are validated, the local clock synchronizes, allowing the router to assign itself Stratum 3 (upstream Stratum 2 + 1). Finally, the router serves downstream clients accurately.

Adım Adım Çözüm

1
Identify the initial configuration trigger
The command `ntp server 10.1.1.50` creates the server association.
No NTP message exchange can take place until the target IP server is defined in the configuration.
2
Analyze the packet exchange sequence
The router initiates NTP polling requests over UDP port 123.
Timestamped control packets must be exchanged to filter dispersion and compute clock offset.
3
Determine system clock adjustment
The system clock synchronizes to the upstream reference time.
Clock offset calculation must be completed before the router can adjust its internal clock.
4
Calculate the local stratum level
Stratum level becomes Stratum 2 + 1 = Stratum 3.
NTP protocol rules state that a device takes on the stratum level of its reference server plus one.
5
Identify downstream server operation
The router acts as an authoritative time source for internal network devices.
A Cisco router only advertises valid, authoritative time to clients after its own clock is synchronized.

Anahtar Kavram

NTP Synchronization Sequence and Stratum Propagation
Tahmini Süre:1m 30s
Soru 7Soru →

A network administrator needs to configure a Cisco IOS router to synchronize its internal clock with an external centralized time source at IP address 192.168.10.50. Which Cisco IOS global configuration command must be used to accomplish this task?

Cevabı ve açıklamayı göster

Cevap: ntp server 192.168.10.50

Cevap

The command 'ntp server 192.168.10.50' configures the router to act as an NTP client synchronizing from the specified NTP server.
The correct command is 'ntp server 192.168.10.50'. In Cisco IOS, entering 'ntp server' followed by an IP address configures the router to request time updates from that remote server.

Adım Adım Çözüm

1
Identify the required NTP operational mode.
The router must act as an NTP client receiving time synchronization from a specified IP address.
The scenario specifies referencing a central time source at 192.168.10.50.
2
Select the appropriate Cisco IOS global configuration command syntax.
The command 'ntp server <ip-address>' establishes the client-server relationship.
'ntp server' is the dedicated Cisco IOS command for designated client NTP synchronization.

Anahtar Kavram

NTP Client Operations and Configuration
Tahmini Süre:45s
Soru 8Soru →

An administrator is verifying Network Time Protocol (NTP) operations on a Cisco IOS router. Which of the following statements regarding NTP functionality and status are correct? (Select TWO.)

Geçerli olan tümünü seçin

Cevabı ve açıklamayı göster

Cevap: The command `ntp master 4` configures the router to act as an NTP server serving time at stratum 4.; A stratum value of 16 indicates that the local device clock is unsynchronized and considered invalid.

Cevap

The command `ntp master 4` configures the router as an NTP server at stratum 4, and a stratum level of 16 indicates an unsynchronized clock state.
Configuring `ntp master 4` causes the router to act as an authoritative NTP clock source at stratum 4. Furthermore, stratum 16 is the standard NTP representation for an unsynchronized device or an unreachable clock source.

Adım Adım Çözüm

1
Analyze NTP stratum range and master configuration commands.
The `ntp master [number]` command allows an IOS router to advertise itself as an NTP master at the specified stratum. Valid synchronized strata are 1 through 15.
Stratum 1 is directly attached to a reference clock (like GPS/atomic), and each hop increments the stratum by 1. Stratum 16 defines an unsynchronized state.
2
Evaluate transport layer protocols used by NTP.
NTP uses UDP port 123.
UDP is chosen over TCP to minimize latency and synchronization overhead.

Anahtar Kavram

NTP Stratum Hierarchy and Master Configuration
Tahmini Süre:45s
Soru 9Soru →

A network engineer is configuring a new Cisco IOS router (R1) to synchronize its system time with a primary enterprise NTP server operating at Stratum 2. R1 is also expected to act as an NTP server for downstream switches once synchronized. Arrange the operational steps in the exact chronological sequence in which R1 processes NTP synchronization from initial CLI configuration to serving downstream clients.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence starts with entering the NTP server configuration command, followed by sending UDP port 123 query packets, receiving the Stratum 2 response, calculating the local Stratum 3 value, and finally transitioning to synchronized state while serving downstream clients.
The operational sequence moves logically from CLI command execution, outward network request over UDP 123, inbound response processing, mathematical stratum calculation (2+1=32 + 1 = 3), to local state synchronization and downstream service activation.

Adım Adım Çözüm

1
Identify the initial configuration trigger
Execution of 'ntp server 10.10.10.1' initializes the local NTP daemon polling timer.
NTP operations cannot begin until a server association is defined in configuration.
2
Determine initial packet transmission details
R1 sends outgoing NTP client polling messages using UDP port 123.
NTP uses UDP port 123 for all client/server communications.
3
Process server response details
R1 receives packet payload containing Stratum 2 marker from 10.10.10.1.
The upstream server reports its own stratum distance from reference clock (Stratum 2).
4
Perform Stratum level mathematical calculation
Local stratum is evaluated as Server Stratum+1=2+1=3\text{Server Stratum} + 1 = 2 + 1 = 3.
Every network hop down the NTP hierarchy increments the Stratum level by exactly 1.
5
Establish synchronized state and downstream server role
System clock updates to synchronized state, enabling R1 to answer downstream queries at Stratum 3.
A Cisco router will not serve authoritative time to downstream clients until its own clock is synchronized to an upstream source.

Anahtar Kavram

NTP Client-Server Synchronization Workflow and Stratum Calculation
Tahmini Süre:2m 0s
Soru 10Soru →

A network technician needs to configure a Cisco router to operate as an Network Time Protocol (NTP) client and synchronize its internal system clock with a central time server located at IP address 172.16.10.100. Which global configuration command must be executed on the router to accomplish this task?

Cevabı ve açıklamayı göster

Cevap: ntp server 172.16.10.100

Cevap

The command 'ntp server 172.16.10.100' in global configuration mode configures the local Cisco device as an NTP client that synchronizes its system time from the specified IP address.
The command 'ntp server 172.16.10.100' instructs the Cisco IOS router to operate as an NTP client in client-server mode, sending unicast NTP requests to the specified IP address to synchronize its clock.

Adım Adım Çözüm

1
Identify the role required for the router.
The router must act as an NTP client receiving time from an external server.
The requirement states that the router needs to synchronize its clock to an existing centralized server at IP address 172.16.10.100.
2
Evaluate Cisco IOS NTP configuration commands.
The command 'ntp server <ip-address>' establishes client-server NTP association.
Global configuration command 'ntp server 172.16.10.100' configures the router to query the NTP daemon at 172.16.10.100 for time updates.

Anahtar Kavram

NTP Client Configuration
Soru 11Soru →

An administrator inspects the output of the `show ntp associations` command on router Core-R1:

text
address ref clock st when poll reach delay offset disp
*~192.168.50.2 10.1.1.1 2 15 64 377 2.12 0.18 0.45
~192.168.60.2 127.127.1.1 16 - 64 0 0.00 0.00 16000.

Core-R1 is also configured with the `ntp master 6` command. Router Branch-R2 is configured to synchronize its clock with Core-R1 using the command `ntp server 192.168.10.1` (Core-R1's IP address).

Which statement accurately describes the resulting NTP operational status and stratum hierarchy for both devices once synchronization is fully established?

Cevabı ve açıklamayı göster

Cevap: Core-R1 operates at Stratum 3, and Branch-R2 operates at Stratum 4.

Cevap

Core-R1 operates at Stratum 3, and Branch-R2 operates at Stratum 4.
In Cisco IOS NTP operation, an asterisk (`*`) in `show ntp associations` designates the current synchronized time source. Because 192.168.50.2 is at Stratum 2, Core-R1 becomes Stratum 3 (2+1=32 + 1 = 3). The `ntp master` command acts only as an authoritative clock fallback when no synchronized upstream clock is present, so `ntp master 6` is inactive. Consequently, Branch-R2 synchronizing to Core-R1 receives Stratum 3 time and becomes Stratum 4 (3+1=43 + 1 = 4).

Adım Adım Çözüm

1
Analyze the output of `show ntp associations` on Core-R1.
The asterisk `*` next to `192.168.50.2` indicates that Core-R1 is actively synchronized to this server. The `st` column shows that this server operates at Stratum 2.
An NTP client increments the stratum value of its configured reference clock by 11.
2
Evaluate the impact of the `ntp master 6` command on Core-R1.
Core-R1's effective stratum is 2+1=32 + 1 = 3. The `ntp master 6` setting is ignored.
The `ntp master` command serves as a fallback clock source only when no active, valid external NTP server is synchronized.
3
Calculate the stratum level for Branch-R2.
Branch-R2 synchronizes to Core-R1 (Stratum 3), resulting in a stratum level of 3+1=43 + 1 = 4 for Branch-R2.
Each hop down the NTP distribution tree adds 11 to the stratum level.

Anahtar Kavram

NTP Stratum Hierarchy and Precedence
Tahmini Süre:2m 0s
Soru 12Soru →

An enterprise router is configured with the command `ntp master 4` and has an active server association configured via `ntp server 10.20.30.5` (which is a Stratum 2 reference source). The command `show ntp status` indicates that the clock is currently synchronized to 10.20.30.5. Which TWO statements accurately describe the NTP operational behavior and stratum hierarchy in this deployment? (Select two.)

Geçerli olan tümünü seçin

Cevabı ve açıklamayı göster

Cevap: The router functions at Stratum 3 because it dynamically calculates its stratum level by incrementing the Stratum 2 source's level by 1 while synchronized.; If connectivity to 10.20.30.5 is lost and all external NTP references become unreachable, the router will fall back to serving time at Stratum 4.

Cevap

The router functions at Stratum 3 by incrementing the external Stratum 2 source by 1, and if the external source becomes unreachable, the router falls back to operating at Stratum 4 using its internal clock.
When a router is actively synchronized to an external Stratum 2 NTP server, its operational stratum level becomes Stratum 3 (upstream stratum + 1). The configured `ntp master 4` command acts as a fallback mechanism; if external synchronization is lost, the router maintains NTP server capability by serving time to downstream clients at Stratum 4.

Adım Adım Çözüm

1
Analyze the active NTP synchronization state
The router is actively synchronized to 10.20.30.5, which operates at Stratum 2.
When synchronized to an active NTP server, a router dynamically calculates its stratum by adding 1 to the upstream server's stratum level (2+1=32 + 1 = 3).
2
Evaluate the fallback mechanism of the `ntp master` command
The `ntp master 4` command serves as a secondary/fallback source.
While synchronized to a valid external reference, the local NTP master logic remains dormant. If all external sources fail, the router defaults to using its system clock as a Stratum 4 source for downstream devices.

Anahtar Kavram

NTP Stratum Calculation and Master Fallback Operation
Soru 13Soru →

A network administrator at an enterprise branch office is troubleshooting an unsynchronized NTP client on a Cisco router named Branch-R1. The router has IP reachability to an authoritative internal time server at IP address 10.50.1.1010.50.1.10, but security firewalls along the transit path strictly enforce access rules that permit management services only if they originate from Branch-R1's dedicated Loopback0 interface (10.255.1.110.255.1.1). Currently, NTP packets generated by the router are dropped by the firewall because they use the egress physical interface IP address as their source. Which global configuration command must be configured on Branch-R1 to force all outgoing NTP traffic to originate from the specified loopback interface?

Cevabı ve açıklamayı göster

Cevap: ntp source Loopback0

Cevap

The command 'ntp source Loopback0' forces the router to use the IP address of interface Loopback0 as the source IP address in all outgoing NTP packets.
The correct option specifies 'ntp source Loopback0'. In Cisco IOS, outgoing NTP packets by default derive their source IP address from the outbound interface used to reach the destination. When security appliances require management traffic to originate from a consistent logical interface (such as a loopback interface), the global configuration command 'ntp source <interface>' forces the router to place that interface's IP address into the source field of all generated NTP packets.

Adım Adım Çözüm

1
Identify the operational requirement for NTP traffic
NTP packets must be sourced from Loopback0 (10.255.1.110.255.1.1) so they match firewall security rules.
By default, Cisco IOS uses the IP address of the egress interface facing the destination server as the packet source address.
2
Select the correct Cisco IOS CLI command to specify the NTP source interface
The global configuration command 'ntp source Loopback0' instructs the NTP process to always use Loopback0's IP address.
Configuring 'ntp source <interface>' guarantees consistent sourcing regardless of which physical interface forwards the traffic.

Anahtar Kavram

NTP Source Interface Configuration
Soru 14Soru →

A network engineer is configuring a Cisco IOS router named Edge-R1 to operate as an NTP client. The router must synchronize its system clock with an upstream central NTP server at IP address 10.45.1.1. Additionally, organizational security policy dictates that all outgoing NTP packets must originate specifically from the router's Loopback0 interface rather than the physical egress interface. Which two global configuration commands must be configured on Edge-R1 to fulfill these operational requirements?

Geçerli olan tümünü seçin

Cevabı ve açıklamayı göster

Cevap: ntp server 10.45.1.1; ntp source Loopback0

Cevap

The two correct global configuration commands are 'ntp server 10.45.1.1' to identify the time server and 'ntp source Loopback0' to force NTP packets to use the specified interface address.
To establish NTP synchronization with an external time source, the command 'ntp server 10.45.1.1' is required to specify the remote NTP server IP address. Additionally, enforcing that all NTP control traffic originates from a designated logical interface requires the global command 'ntp source Loopback0'.

Adım Adım Çözüm

1
Identify the command required to configure an NTP server target.
The global configuration command 'ntp server 10.45.1.1' configures the router to solicit time messages from 10.45.1.1.
NTP client functionality requires pointing the device to an authoritative upstream clock source.
2
Identify the command required to set the source interface for outbound NTP traffic.
The global configuration command 'ntp source Loopback0' ensures all outbound NTP requests use the IP address assigned to Loopback0 as their source address.
By default, Cisco IOS uses the IP address of the egress interface facing the destination; configuring an explicit source interface standardizes control plane traffic origin.

Anahtar Kavram

Cisco IOS NTP Client and Source Interface Configuration
Soru 15Soru →

An administrator executes the `show ntp associations` command on a Cisco IOS router to verify system time synchronization. The command output is displayed below:

text
address ref clock st when poll reach delay offset disp
~172.16.50.2 10.1.1.1 2 42 64 377 12.45 1.120 0.45
*192.168.20.5 10.1.1.1 2 15 64 377 4.10 0.210 0.15

Based on this output, which statement accurately describes the NTP operational status of the local router?

Cevabı ve açıklamayı göster

Cevap: The router is synchronized to 192.168.20.5 and will operate as a Stratum 3 NTP server for downstream clients.

Cevap

The router is synchronized to 192.168.20.5 and will operate as a Stratum 3 NTP server for downstream clients.
In Cisco IOS `show ntp associations` output, the asterisk (`*`) denotes the server with which the router is currently synchronized. Since the server at 192.168.20.5 has a stratum level of 2 (`st = 2`), the local router increments this value by 1, operating as a Stratum 3 NTP server when serving downstream clients.

Adım Adım Çözüm

1
Analyze the symbol prefix in the `show ntp associations` output.
The asterisk (`*`) symbol next to `192.168.20.5` indicates that this IP address is selected as the current synchronized reference clock. The tilde (`~`) symbol indicates a configured association.
Cisco IOS uses symbol codes in CLI outputs to distinguish between candidate peers, configured servers, and the actively chosen time source.
2
Determine the stratum level of the upstream time server.
The `st` column for `192.168.20.5` displays a stratum value of 2.
Stratum measures the distance from a high-precision reference clock (Stratum 0).
3
Calculate the stratum level of the local router.
Local Stratum = Upstream Stratum + 1 = 2 + 1 = 3.
An NTP client/server increments the stratum number by 1 relative to its synchronized server.

Anahtar Kavram

NTP Output Verification and Stratum Hierarchy Calculation
Tahmini Süre:1m 15s