Examkin

Brake System Components Inspection

65 soru

Tüm türler65Çoktan seçmeli33Doğru / Yanlış10Eşleştirme12Sıralama10
Soru 61Soru →

A driver is preparing to check the pushrod free play on manual slack adjusters during a pre-trip foundation brake inspection. Place the following procedural steps in the correct operational sequence from first to last.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct operational sequence begins with securing the vehicle using wheel chocks, releasing the cab parking brakes to remove spring tension from the chambers, firmly pulling each slack adjuster by hand, and verifying that pushrod travel does not exceed approximately 1 inch1\text{ inch}.
To accurately and safely inspect manual slack adjusters, the vehicle must first be secured against movement with wheel chocks on level pavement. Releasing the cab parking brake valve relieves spring brake force so the pushrods can move. Pulling firmly on each slack adjuster by hand allows the driver to confirm that free play does not exceed the legal safety threshold of approximately 1 inch1\text{ inch}.

Adım Adım Çözüm

1
Establish initial vehicle safety and roll prevention
Chock the wheels on flat, level ground.
Releasing the parking brakes without wheel chocks creates an immediate and hazardous runaway risk.
2
Disengage spring brakes to allow component movement
Push in the parking brake control valve in the cab.
Spring brakes hold the pushrod locked in place under heavy spring pressure; they must be released to measure free play.
3
Exert manual force on foundation brake linkage
Pull hard on each slack adjuster by hand.
Direct manual pulling tests the mechanical slack between the brake shoe and drum.
4
Evaluate measured free play against CDL safety tolerances
Confirm total pushrod movement is no more than approximately 1 inch1\text{ inch}.
Pushrod free play exceeding 1 inch1\text{ inch} on a manual slack adjuster indicates excessive clearance and requires adjustment before operating.

Anahtar Kavram

Standard step-by-step procedure for testing manual slack adjuster pushrod free play during vehicle inspection
Tahmini Süre:1m 0s
Soru 62Soru →

During a pre-trip walkaround inspection of an air-braked commercial vehicle parked on level ground with the wheels chocked and parking brakes released, a driver inspects the foundation brake assemblies and mechanical linkages. Which of the following observations indicates a safety defect that requires mechanical adjustment or repair before operating the vehicle?

Cevabı ve açıklamayı göster

Cevap: The manual slack adjuster pushrod moves more than 1 inch from the brake chamber when pulled firmly by hand.

Cevap

The condition indicating a safety defect requiring repair is when the manual slack adjuster pushrod moves more than 1 inch from the brake chamber when pulled firmly by hand.
When checking manual slack adjusters on an S-cam foundation brake assembly, the vehicle must be parked on level ground with the wheels chocked and parking brakes released. Under manual pull with a tool or hand, pushrod free play should not exceed approximately 1 inch. Travel greater than 1 inch indicates the foundation brake is out of adjustment, which compromises stopping distance and requires immediate mechanical adjustment.

Adım Adım Çözüm

1
Identify the proper pre-trip inspection conditions for checking manual slack adjuster free play.
The vehicle must be parked on level ground, wheels chocked, and parking/spring brakes released so the pushrod is free to move.
If the spring brakes are applied, the pushrod cannot be pulled manually to measure free play.
2
Evaluate the allowable manual pushrod travel against commercial motor vehicle safety standards.
Free play travel must not exceed approximately 1 inch (25.4 mm) on manual slack adjusters when pulled firmly by hand.
Pushrod travel exceeding 1 inch indicates excessive clearance between brake shoes and the drum, reducing braking effectiveness and risking brake failure.
3
Compare all stated component observations against regulatory thresholds.
A pushrod stroke exceeding 1 inch is an out-of-adjustment defect, whereas 3/8 inch lining thickness (above the 1/4 inch minimum) and a 90-degree applied working angle are proper operating conditions.
Mastery of foundation brake safety criteria requires distinguishing valid mechanical defects from acceptable operating tolerances and testing errors.

Anahtar Kavram

Foundation Brake Inspection Tolerances and Pushrod Free Play Limits
Tahmini Süre:1m 0s
Soru 63Soru →

Friction linings or brake pads found contaminated with oil, grease, or hub lubricant during an inspection are considered safe for operation provided that the remaining lining thickness exceeds 14 inch\frac{1}{4}\text{ inch}.

Cevabı ve açıklamayı göster

Cevap: False

Cevap

False
The statement is false because any grease, oil, or brake fluid contamination on brake shoes, pads, drums, or rotors is a critical safety defect that requires immediate repair or replacement, regardless of how much friction material remains.

Adım Adım Çözüm

1
Analyze the component condition and the proposed exception in the statement.
The statement claims that adequate lining thickness (greater than 14 inch\frac{1}{4}\text{ inch}) overrides the hazard of lubricant contamination on friction surfaces.
Commercial vehicle foundation brake inspection standards establish specific, non-negotiable safety criteria for both physical wear and surface contamination.
2
Evaluate standard commercial motor vehicle safety criteria regarding contaminated friction material.
Any evidence of grease, oil, or hub seal leakage on brake linings or drums renders the component defective and out of service.
Lubricants dramatically reduce friction coefficient, cause severe brake imbalance, increase stopping distance, and create a fire hazard under heavy braking.
3
Determine the validity of the overall statement.
The statement is false because adequate thickness does not compensate for compromised friction integrity.
Both conditions—sufficient thickness and clean, uncontaminated friction surfaces—must be satisfied for the foundation brakes to pass inspection.

Anahtar Kavram

Brake friction lining contamination defect criteria
Tahmini Süre:1m 0s
Soru 64Soru →

An operator inspects the foundation air brake components on a commercial combination vehicle. Which of the following findings indicates that a manual slack adjuster is out of adjustment and requires maintenance?

Cevabı ve açıklamayı göster

Cevap: Pushrod free play exceeds 1 inch when pulled firmly by hand with the parking brakes disengaged.

Cevap

Pushrod free play exceeding 1 inch when pulled firmly by hand with the parking brakes disengaged indicates an out-of-adjustment condition requiring service.
On commercial vehicles equipped with manual slack adjusters, free play travel of the pushrod should not exceed approximately 1 inch when pulled firmly by hand with the parking brakes released and wheels chocked.

Adım Adım Çözüm

1
Determine the proper procedural condition for checking manual slack adjuster free play.
Vehicle must be on level ground with wheels chocked and parking brakes released so the pushrod can move freely.
Keeping the parking brakes applied locks the foundation brake assembly, preventing an accurate free play measurement.
2
Compare observed mechanical tolerances against CDL foundation brake safety thresholds.
Manual slack adjuster pushrod movement must not exceed approximately 1 inch when pulled firmly by hand.
Excessive pushrod stroke causes brake lag, reduced stopping torque, and potential foundation brake failure.

Anahtar Kavram

Manual slack adjuster free play inspection threshold
Tahmini Süre:1m 0s
Soru 65Soru →

A commercial motor vehicle driver performs a safety check of the S-cam foundation brake mechanisms following an en-route stop. When inspecting the manual slack adjusters with the vehicle parked on flat ground, wheels securely chocked, and parking brakes released, which finding confirms the pushrod stroke is within acceptable safety tolerances?

Cevabı ve açıklamayı göster

Cevap: The pushrod moves no more than 1 inch from the brake chamber when pulled firmly by hand.

Cevap

The pushrod moves no more than 1 inch from the brake chamber when pulled firmly by hand.
For manual slack adjusters on S-cam foundation brakes, pushrod free play should not exceed 1 inch when pulled firmly by hand with the vehicle parked on level ground, wheels chocked, and parking brakes released. This ensures proper brake shoe-to-drum clearance and effective stopping power.

Adım Adım Çözüm

1
Establish the proper vehicle testing setup for manual pushrod travel inspection.
The commercial vehicle is parked on level ground, wheels are chocked, air pressure is at normal operating level, and parking/spring brakes are fully released.
Releasing the parking brakes removes spring tension from the chamber, allowing manual movement of the pushrod and slack adjuster.
2
Apply manual force by pulling the slack adjuster pushrod firmly by hand or using a pry bar.
The total free play displacement from the released position to shoe contact is measured.
This physical measurement verifies whether brake clearance and adjustment meet safety tolerances.
3
Evaluate the measured travel against Commercial Driver's License regulatory standards.
Displacement is 1 inch or less, confirming the manual slack adjuster is properly adjusted.
Any travel exceeding 1 inch requires immediate mechanical adjustment to maintain safe stopping capability.

Anahtar Kavram

Manual slack adjuster pushrod travel tolerance and foundation brake inspection procedures
Tahmini Süre:1m 0s
ÖncekiSayfa 4 / 4
Brake System Components Inspection Alıştırma Soruları — Commercial Driver's License (CDL) General Knowledge Exam — Sayfa 4 | Examkin