Tüm alıştırma soruları

5215 soru

Tüm türler5,215 Çoktan seçmeli2,665 Çoklu seçim6 Doğru / Yanlış260 Sayısal512 Eşleştirme930 Sıralama396 Boşluk doldurma397 Kısa cevap49

Soru 1261Soru →

A $24\text{ V}$ direct-current (DC) power bus supplies two cooling fans connected in parallel inside a communications cabinet. The primary fan draws a steady branch current of $3\text{ A}$ , while the secondary fan has an internal resistance of $12\text{ }\Omega$ . What is the total current, in amperes ( $\text{A}$ ), delivered by the power bus to the parallel circuit?

Cevabı ve açıklamayı göster

Cevap: 5

Cevap

The total current delivered by the power bus is

5\text{ A}

In a parallel DC circuit, the source voltage (

24\text{ V}

) is applied directly across each branch. The secondary branch current is found using Ohm's law:

I_2 = \frac{24\text{ V}}{12\text{ }\Omega} = 2\text{ A}

. Adding the known primary branch current (

3\text{ A}

) to the secondary branch current (

2\text{ A}

) yields the total source current of

5\text{ A}

Adım Adım Çözüm

Determine the voltage across the secondary branch

Voltage across the secondary fan is

24\text{ V}

In any parallel circuit, every branch experiences the identical full source voltage (

V_{\text{total}} = V_1 = V_2

Calculate the secondary branch current (

I_2

) using Ohm's law

I_2 = \frac{24\text{ V}}{12\text{ }\Omega} = 2\text{ A}

Ohm's law states that current equals voltage divided by resistance (

I = \frac{V}{R}

Sum all individual branch currents to determine total circuit current

I_{\text{total}} = 3\text{ A} + 2\text{ A} = 5\text{ A}

Total current in a parallel circuit is the sum of the individual branch currents (

I_{\text{total}} = I_1 + I_2

Anahtar Kavram

Parallel Circuit Current and Ohm's Law

Tahmini Süre:1m 0s

Soru 1262Soru →

During the power stroke of an internal combustion engine, high-pressure combustion gases drive mechanical components to produce rotational power. In what sequence is mechanical force transferred from initial gas expansion to final rotational torque?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence of force transmission is: expanding gases push the piston crown, force transfers through the wrist pin, travels down the connecting rod, and is converted into rotational torque by the crankshaft.

Force transmission strictly follows physical mechanical connectivity: combustion pressure acts on the piston crown, passes through the wrist pin into the small end of the connecting rod, travels through the rod body, and applies force to the crankshaft rod journal where linear reciprocating motion becomes rotational torque.

Adım Adım Çözüm

Identify the initial point of force generation in the cylinder.

Ignited air-fuel mixture expands and presses directly onto the piston crown.

Force generation starts at the combustion chamber boundary.

Trace the mechanical link directly connected to the piston body.

The wrist pin (gudgeon pin) receives the downward thrust from the piston boss.

The wrist pin couples the piston to the upper end of the connecting rod.

Follow the structural transfer of load through the linkage rod.

The connecting rod beam carries the compressive force downward to the lower rod bearing.

The connecting rod bridges the linear motion of the piston to the rotating assembly.

Identify the component responsible for converting reciprocating motion to rotary motion.

The offset crankpin journal of the crankshaft turns the linear push into rotational torque.

The crankshaft provides the final rotational mechanical output for the engine.

Anahtar Kavram

Linear to rotary motion conversion and internal engine load path

Tahmini Süre:1m 0s

Soru 1263Soru →

An avionics technician replaces a copper ground wire in an aircraft instrument panel. The replacement copper wire is twice as long and has twice the diameter of the original wire. If the original wire had a measured resistance of $0.4\ \Omega$ , what is the electrical resistance of the replacement wire?

0.8\ \Omega

0.2\ \Omega

0.4\ \Omega

1.6\ \Omega

Cevabı ve açıklamayı göster

Cevap: $0.2\ \Omega$

Cevap

The electrical resistance of the replacement wire is

0.2\ \Omega

The electrical resistance of a conductor is determined by the formula

R = \rho \frac{L}{A}

, where

\rho

is resistivity,

L

is length, and

A

is cross-sectional area. Because the wire cross-section is circular,

A = \frac{\pi d^2}{4}

, meaning area scales with the square of diameter (

d^2

). Doubling the diameter increases the cross-sectional area by a factor of

2^2 = 4

. Doubling the length increases resistance by a factor of

2

. Combining these gives a new resistance of

\frac{2}{4} \times 0.4\ \Omega = 0.5 \times 0.4\ \Omega = 0.2\ \Omega

Adım Adım Çözüm

Identify the relationship between conductor dimensions and resistance

The resistance formula is

R = \rho \frac{L}{A}

, where cross-sectional area is

A = \frac{\pi d^2}{4}

Resistance varies directly with length

L

and inversely with cross-sectional area

A

Determine the change in cross-sectional area when diameter doubles

Since

A \propto d^2

, doubling the diameter (

2d

) increases cross-sectional area by a factor of

2^2 = 4

Area is proportional to the square of the diameter for a circular cross-section.

Calculate the scaling factor for total resistance

The new resistance scales by

\frac{\text{length factor}}{\text{area factor}} = \frac{2}{4} = 0.5

Doubling length multiplies resistance by

2

, and quadrupling area divides resistance by

4

Calculate the final resistance of the replacement wire

R_{\text{new}} = 0.5 \times 0.4\ \Omega = 0.2\ \Omega

Multiplying the baseline resistance by the net geometric scaling factor yields the new resistance value.

Anahtar Kavram

Conductor resistance is directly proportional to length and inversely proportional to the square of its diameter (

R = \rho L / A

Tahmini Süre:1m 0s

Soru 1264Soru →

During the installation of a radio receiver system, a technician must prepare the end of an RG-6 coaxial cable to fit an F-type compression connector. To properly seat the connector, the outer plastic jacket, braided shield foil, and inner dielectric insulator must be stripped at precise staggered depths without nicking the solid center conductor. Which specialized wire preparation tool is designed to perform this multi-tiered strip in a single operation?

Multi-gauge wire stripper

Rotary coaxial cable stripper

Diagonal cutting pliers

Ratcheting terminal crimper

Cevabı ve açıklamayı göster

Cevap: Rotary coaxial cable stripper

Cevap

Rotary coaxial cable stripper

A rotary coaxial cable stripper is specifically engineered with two or three staggered, depth-adjustable blades that cut the outer jacket, metallic shield, and dielectric to the exact stepped dimensions required for connector attachment in one rotating motion.

Adım Adım Çözüm

Analyze the cable structure and termination requirements

Coaxial cable contains concentric layers: outer jacket, metallic shield braid/foil, dielectric insulator, and central conductor requiring a tiered, staggered strip profile.

Compression and crimp coaxial connectors require the center conductor and dielectric to be exposed at specific, precise lengths for proper impedance matching and electrical contact.

Evaluate tool capabilities against the required preparation procedure

The rotary coaxial stripper is equipped with dual or triple staggered blades calibrated to cut each distinct layer to its exact depth simultaneously upon rotation.

Standard single-notch wire strippers or cutters cannot perform multi-level cuts without severe risk of nicking the central conductor or cutting shield braids unevenly.

Anahtar Kavram

Coaxial cable structure and specialized multi-blade stripping tools

Tahmini Süre:45s

Soru 1265Soru →

When a vehicle makes a turn, the outside drive wheel must travel along a longer path than the inside drive wheel. Which drivetrain component enables the drive wheels on the same axle to rotate at different speeds while delivering power?

Shock absorber

Differential

Brake rotor

Universal joint

Cevabı ve açıklamayı göster

Cevap: Differential

Cevap

Differential

The differential assembly contains internal spider gears and side gears that permit the left and right drive wheels to rotate at different speeds when cornering, while steadily delivering engine torque from the driveshaft.

Adım Adım Çözüm

Analyze the mechanical requirements of vehicle turning

During a turn, the outside wheel travels a wider arc and must rotate faster than the inside wheel.

If both wheels were locked to rotate at the same speed, the tires would scrub and hop during turns.

Identify the drivetrain component responsible for splitting axle torque while allowing speed variance

The differential assembly uses side gears and spider pinions to allow left and right axle shafts to turn at different rates while receiving continuous drive torque.

The core function of an automotive differential is to balance driving power while accommodating wheel speed differences in turns.

Anahtar Kavram

Differential Function and Cornering Operation

Tahmini Süre:45s

Soru 1266Soru →

A mechanic is evaluating a modern internal combustion engine equipped with a full-flow filtration circuit during a cold start in sub-freezing ambient conditions. Immediately after ignition, the dashboard oil pressure gauge registers a maximum peg-out reading, but pronounced metallic tapping is clearly heard from the cylinder head. The engine coolant temperature gauge remains at its lowest mark. Based on these concurrent symptoms, which of the following identifies the most mechanically sound underlying cause?

The motor oil viscosity is excessively high for the ambient temperature, resulting in extreme pressure at the pump discharge but severely restricting fluid flow to the upper valvetrain.

The engine thermostat is stuck in the closed position, preventing proper heat dissipation and causing the hydraulic valve lifters to prematurely expand and strike the camshaft.

The cold-start air-fuel mixture is running excessively lean, which triggers early detonation during the compression stroke and creates an audible metallic knocking sound.

The four-stroke combustion sequence is misaligned due to a slipped timing chain, forcing the intake valves to mechanically strike the pistons during the exhaust phase.

Cevabı ve açıklamayı göster

Cevap: The motor oil viscosity is excessively high for the ambient temperature, resulting in extreme pressure at the pump discharge but severely restricting fluid flow to the upper valvetrain.

Cevap

The motor oil viscosity is excessively high for the ambient temperature, resulting in extreme pressure at the pump discharge but severely restricting fluid flow to the upper valvetrain.

The correct answer accurately distinguishes between oil pressure and oil flow. In sub-freezing temperatures, motor oil becomes highly viscous (thick). When the engine starts, the oil pump attempts to push this thick oil through the narrow passages leading to the cylinder head. The high resistance causes a massive pressure spike at the sending unit (pegging the gauge), but the actual flow rate is too slow. As a result, the camshaft and valve lifters are temporarily starved of oil, producing a metallic tapping noise until the oil warms up and flows properly.

Adım Adım Çözüm

Analyze the reported operational environment and symptoms.

The engine is in sub-freezing conditions, has a pegged high oil pressure gauge immediately upon startup, features tapping from the top end, and is still cold.

Establishing baseline conditions is required to isolate which mechanical system could cause all symptoms simultaneously.

Evaluate the relationship between low temperatures and fluid dynamics in the lubrication system.

Cold temperatures drastically increase oil viscosity, making it thicker and more resistant to flowing through small passages.

Understanding viscosity behavior explains the disparity between what the gauge reads and what the engine parts are experiencing.

Differentiate between fluid pressure and actual fluid flow.

The oil pump forces thick oil against the restriction of the cold filter and narrow galleys, spiking pressure at the sending unit (high gauge reading), while the restriction prevents adequate volume from reaching the top of the engine (causing dry valvetrain tapping).

A high pressure reading does not guarantee high flow; in extreme cold, it often indicates a flow restriction.

Eliminate distractors based on the symptom profile.

Thermostat issues, lean fuel mixtures, and valve timing alignment do not concurrently cause localized valvetrain noise AND pegged oil pressure upon a cold start.

Verifying that no other subsystem can account for the exact combination of evidence confirms the diagnosis.

Anahtar Kavram

The inverse relationship between fluid pressure and flow volume when cold-temperature viscosity restrictions occur in an engine lubrication circuit.

Tahmini Süre:1m 30s

Soru 1267Soru →

A technician is diagnosing a vehicle with a no-crank condition. When the ignition switch is turned to the START position, a single distinct click is heard from the starter solenoid, but the engine does not turn over. A digital multimeter connected directly across the battery posts reads $12.6\text{ V}$ at rest and drops slightly to $12.2\text{ V}$ when the key is held in the START position. However, measuring between the starter motor's main positive battery terminal ( $B$ -terminal) and the starter case ground shows $12.5\text{ V}$ at rest, but drops to $0.4\text{ V}$ during the crank attempt. Which of the following is the most likely root cause of this failure?

A discharged 12-volt battery unable to supply high cranking amperage

High resistance in the positive battery cable or its terminal connections

An internal short circuit across the alternator stator windings

A seized starter motor armature drawing locked-rotor current

Cevabı ve açıklamayı göster

Cevap: High resistance in the positive battery cable or its terminal connections

Cevap

High resistance in the positive battery cable or its terminal connections

The correct answer is high resistance in the positive battery cable or its terminal connections. When the ignition switch activates the starter solenoid, the heavy internal contact disc closes to connect the battery feed to the starter motor windings. Because high resistance exists along the cable or connection (due to corrosion, looseness, or damaged strands), the attempted current draw causes a massive voltage drop across the resistance point, leaving only

0.4\text{ V}

at the starter motor. The battery itself maintains

12.2\text{ V}

, proving the voltage drop is strictly isolated to the feed circuit.

Adım Adım Çözüm

Analyze the battery state of charge and battery post voltage under load.

The battery post voltage is

12.6\text{ V}

open circuit and stays at

12.2\text{ V}

during the crank attempt, confirming the battery is fully charged and not under excessive total load.

A healthy, fully charged automotive lead-acid battery maintains

>9.6\text{ V}

during starting.

Evaluate the voltage drop between the battery and the starter motor main terminal.

Voltage at the starter drops from

12.5\text{ V}

down to

0.4\text{ V}

during the attempt, indicating an unwanted voltage drop of over

11.8\text{ V}

(

12.2\text{ V} - 0.4\text{ V}

) across the supply line.

According to Ohm's law (

V = IR

), when current flows through high unwanted resistance (corrosion, loose terminal, frayed cable), voltage drops significantly across that point instead of reaching the load.

Differentiate between an open supply path, a shorted/locked starter, and a cable resistance fault.

The single click confirms the solenoid pull-in coil activates and closes the internal disc contacts, but the supply cable cannot deliver current due to excessive series resistance.

The failure is isolated to the primary current-carrying feed between the battery positive post and the starter terminal.

Anahtar Kavram

Starting circuit voltage drop diagnosis and series circuit resistance behavior under heavy electrical loads.

Tahmini Süre:1m 30s

Soru 1268Soru →

In direct-current (DC) circuit analysis, modifications to individual parallel paths directly impact total resistance, total current, and branch behavior. Match each parallel circuit modification on the left with its resulting electrical effect on the right.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Adding an additional branch matches with decreased total resistance, increased total current, and unaffected existing branches; Increasing one branch resistance matches with decreased branch current, decreased total current, and increased total resistance; Opening one branch matches with increased total resistance, decreased total current, and normal operation of remaining branches; Connecting a short circuit matches with total resistance dropping to zero, bypassing parallel loads, and causing an excessive current surge.

In parallel circuits, each branch receives full source voltage independently. Adding branches decreases total resistance and increases total current without changing existing branch currents. Changing one branch resistance alters only that branch's current and total current. An open circuit disables only the affected branch, whereas a short circuit drops total resistance to zero across all branches.

Adım Adım Çözüm

Analyze the impact of adding a parallel branch

R_{\text{eq}}

decreases and

I_{\text{total}}

increases

Each additional parallel path increases overall circuit conductance (

G_{\text{total}} = G_1 + G_2 + \dots

), lowering equivalent resistance.

Apply Ohm's law to evaluate increasing a single branch's resistance

I_{\text{branch}}

drops,

I_{\text{total}}

drops, and

R_{\text{eq}}

rises

With branch voltage fixed by the power source, current through that branch varies inversely with its resistance.

Determine the effect of an open-circuit fault in one parallel branch

Defective branch current goes to zero while intact branches continue functioning

Parallel branches are electrically independent because each branch connects directly across the full supply voltage.

Evaluate a short-circuit condition across any parallel branch

R_{\text{eq}} \approx 0\ \Omega

and total current surges drastically

A parallel short bridges the supply rails directly, shunting current away from all resistive paths.

Anahtar Kavram

Independent branch operation and equivalent resistance behavior in parallel DC circuits

Tahmini Süre:1m 0s

Soru 1269Soru →

An aircraft instrument panel illumination circuit is connected to a $28\text{ V}$ direct-current (DC) power source. A multimeter measures a steady current flow of $350\text{ mA}$ through the circuit. What is the total electrical resistance of the circuit in ohms ( $\Omega$ )?

Cevabı ve açıklamayı göster

Cevap: 80

Cevap

The total electrical resistance of the circuit is

80\ \Omega

According to Ohm's Law, resistance equals voltage divided by current (

R = \frac{V}{I}

). Converting

350\text{ mA}

to amperes yields

0.35\text{ A}

. Dividing

28\text{ V}

0.35\text{ A}

gives the correct resistance of

80\ \Omega

Adım Adım Çözüm

Convert the current from milliamperes to amperes

I = 350\text{ mA} = 0.35\text{ A}

Ohm's Law calculations require current to be expressed in standard amperes.

Apply Ohm's Law formula solved for resistance

R = \frac{V}{I} = \frac{28\text{ V}}{0.35\text{ A}} = 80\ \Omega

Dividing the applied electromotive force by the current flow yields total circuit resistance.

Anahtar Kavram

Calculating resistance using Ohm's Law (

R = \frac{V}{I}

) with metric prefix conversion (

1\text{ A} = 1{}000\text{ mA}

Tahmini Süre:45s

Soru 1270Soru →

When examining fixed through-hole resistors, what electrical property is directly governed by the component's physical dimensions, and what unit is used to express this capability? Complete the technical statement below.

Aşağıdaki boşlukları doldurun

Although the printed color bands on a standard carbon-composition resistor indicate its electrical resistance and tolerance, the physical size of the resistor body determines its rating, which is measured in .

Cevabı ve açıklamayı göster

Cevap

power (or wattage) and watts (W)

In electronic components, the physical package size of an axial-lead fixed resistor determines its ability to radiate heat into the surrounding air. Consequently, larger resistors have higher power (wattage) ratings, which are quantified in watts (W). The actual resistance value in ohms and the manufacturing tolerance percentage are represented by the color-coded bands printed on the component body.

Adım Adım Çözüm

Identify the electrical property determined by a resistor's physical dimensions and surface area.

Power rating (or wattage / power dissipation capacity)

A larger physical package provides more surface area to safely dissipate thermal energy generated by current flow without overheating or damaging the component.

Identify the standard unit of measurement for electrical power dissipation.

Watts (W)

Resistor power ratings are specified in watts, with common standard through-hole ratings including

1/8\text{ W}

1/4\text{ W}

1/2\text{ W}

1\text{ W}

, and

2\text{ W}

Anahtar Kavram

Resistor physical package size correlates directly to power dissipation rating in watts rather than resistance value in ohms.

Tahmini Süre:45s

Soru 1271Soru →

A quartermaster is organizing a drawer of $60$ uniform patches. The drawer contains $15$ rank insignia patches, $21$ unit patches, and the remaining patches are flag patches. If one patch is randomly selected from the drawer, what is the probability of selecting a flag patch? Express your answer as a decimal.

Cevabı ve açıklamayı göster

Cevap: 0.4

Cevap

0.4

The probability is found by dividing the number of flag patches (

24

) by the total number of patches (

60

). The fraction

\frac{24}{60}

simplifies to

\frac{2}{5}

, which is

0.4

when expressed as a decimal.

Adım Adım Çözüm

Calculate the number of flag patches in the drawer.

60 - (15 + 21) = 60 - 36 = 24

flag patches.

To determine the probability, the exact number of the desired item (flag patches) must first be known.

Set up the probability fraction.

\frac{24}{60}

The probability of a single event is the number of favorable outcomes divided by the total number of possible outcomes.

Convert the fraction to a decimal.

\frac{24}{60} = \frac{2}{5} = 0.4

The question explicitly specifies that the final answer must be expressed as a decimal.

Anahtar Kavram

Single Event Probability

Soru 1272Soru →

A technician discovers that a single front disc brake caliper remains locked and overheats after the brake pedal is released. Which of the following is the most likely cause?

A leaking wheel cylinder piston cup

A broken brake shoe return spring

An internally deteriorated flexible brake hose

A worn rear differential pinion seal

Cevabı ve açıklamayı göster

Cevap: An internally deteriorated flexible brake hose

Cevap

An internally deteriorated flexible brake hose

Internal breakdown of a flexible rubber brake hose can form an internal restriction or flap that acts like a one-way check valve. While master cylinder pressure easily forces fluid through the hose to apply the caliper, the low pressure of releasing the pedal cannot overcome the flap, trapping fluid in the caliper and causing continuous drag and overheating.

Adım Adım Çözüm

Analyze the reported symptom and system architecture

The symptom is localized to a single front wheel equipped with a disc brake caliper that fails to release pressure.

Isolating the issue to one wheel rules out central hydraulic components like the master cylinder or power booster, which affect multiple wheels.

Evaluate hydraulic and mechanical causes of single caliper lockup

When a flexible rubber brake hose deteriorates internally, a piece of rubber can act as a check valve, allowing high pedal pressure to enter the caliper but preventing fluid return.

Brake fluid must flow freely in both directions through the flexible line to permit prompt caliper piston retraction when the pedal is released.

Anahtar Kavram

Hydraulic restriction in flexible brake hoses causing caliper lockup

Tahmini Süre:1m 0s

Soru 1273Soru →

Match each automotive steering system component with its primary mechanical function in a vehicle's steering linkage.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Pitman arm matches converting gearbox sector shaft rotation into lateral movement; Idler arm matches supporting the center link from the frame opposite the gearbox; Tie rod end matches connecting the steering linkage directly to the steering knuckle; Steering column matches transferring driver rotational effort from the steering wheel to the steering gear.

In a standard automotive steering system, each linkage part performs a unique function: the steering column conveys driver rotation from the steering wheel to the gearbox; the pitman arm converts the gearbox rotation into side-to-side linkage motion; the idler arm mounts to the vehicle frame to support the opposite end of the center link; and the tie rod ends connect the linkage to each steering knuckle to turn the front wheels.

Adım Adım Çözüm

Identify the component driven directly by the steering gear output.

The pitman arm converts sector shaft rotational motion to lateral motion.

The pitman arm is mechanically connected to the steering gear output shaft.

Identify the passive frame-mounted support component.

The idler arm supports the center link on the passenger-side frame rail.

An idler arm mirrors the pitman arm's pivot point to maintain parallel steering geometry.

Identify the component that fastens directly to the wheel hub assembly.

The tie rod end connects the linkage to the steering knuckle.

Tie rod ends transmit lateral motion directly into wheel pivoting action.

Identify the input shaft connecting the driver control to the steering box.

The steering column transfers steering wheel rotation to the steering gear.

The column provides the mechanical link between the steering wheel and the gearbox.

Anahtar Kavram

Steering Linkage Component Identification and Roles

Tahmini Süre:45s

Soru 1274Soru →

In an internal combustion engine, cylinder firing produces intermittent torque pulses. What is the primary mechanical purpose of the heavy flywheel mounted to the rear of the crankshaft?

Actuating the intake and exhaust valves at precisely timed intervals

Storing rotational momentum to smooth out power pulses between cylinder firing intervals

Metering the ratio of air and fuel drawn into the intake manifold

Converting reciprocating piston travel into lateral drivetrain motion

Cevabı ve açıklamayı göster

Cevap: Storing rotational momentum to smooth out power pulses between cylinder firing intervals

Cevap

Storing rotational momentum to smooth out power pulses between cylinder firing intervals

Because internal combustion engines deliver power in discrete combustion pulses, the heavy mass of the flywheel provides rotational inertia. This inertia stores kinetic energy during each power stroke and releases it to keep the crankshaft spinning smoothly through the non-power phases.

Adım Adım Çözüm

Analyze the mechanical challenge in multi-cylinder or single-cylinder reciprocating engines

Combustion occurs in brief bursts during individual cylinder power phases, resulting in uneven torque delivery across the engine cycle.

An engine requires a mechanism to maintain continuous rotation during non-power phases such as intake, compression, and exhaust.

Identify the internal component dedicated to rotational inertia and momentum storage

The flywheel is a heavy disc bolted directly to the crankshaft flange that absorbs kinetic energy during combustion and releases it between firing events.

Rotational inertia dampens torsional vibrations and prevents engine stalling or rough operation between individual firing events.

Anahtar Kavram

Flywheel Function and Rotational Momentum in Internal Combustion Engines

Tahmini Süre:1m 0s

Soru 1275Soru →

A direct-current (DC) solar charging circuit contains a standard silicon diode connected in series between the solar panel and a 12-volt battery. Which of the following best explains the primary function of this diode when the solar panel is not producing voltage at night?

It converts the direct current from the battery into alternating current to power the solar panel.

It prevents the battery from discharging backward through the dark solar panel.

It allows bidirectional current flow so the panel and battery maintain identical voltage levels.

It steps up the battery voltage to continuously supply power to the solar cells.

Cevabı ve açıklamayı göster

Cevap: It prevents the battery from discharging backward through the dark solar panel.

Cevap

It prevents the battery from discharging backward through the dark solar panel.

A semiconductor diode permits electrical current to flow in only one direction (from anode to cathode under forward bias). When darkness falls, the solar panel's output drops to zero while the storage battery remains charged at 12 V. This higher potential at the cathode places the diode in reverse bias, creating an open circuit condition that prevents the battery from discharging through the solar panel.

Adım Adım Çözüm

Analyze the circuit state under nighttime conditions.

The unilluminated solar panel produces 0 V, while the connected storage battery maintains approximately 12 V.

Determining the relative electric potentials at the diode terminals identifies its biasing condition.

Determine the bias state of the series diode.

The cathode connected to the battery positive terminal is at a higher potential than the anode connected to the panel, placing the diode in reverse bias.

A semiconductor diode conducts current only when its anode is more positive than its cathode by at least the forward barrier potential.

Identify the resulting circuit behavior.

The reverse-biased diode exhibits extremely high resistance, preventing current from leaving the battery.

This blocking action prevents the battery from draining energy into the internal resistance of the dark solar panel.

Anahtar Kavram

Unidirectional Current Flow and Reverse-Bias Blocking

Tahmini Süre:1m 0s

Soru 1276Soru →

In electrical wiring and cable harness fabrication, technicians must select the proper tool for each distinct wire preparation and termination task. Match each wire preparation tool with its primary function in harness assembly.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Precision wire stripper matches cutting through dielectric insulation at specific AWG gauges without nicking the metal core; Ratcheting wire crimper matches compressing solderless lug barrels onto bare conductor strands with calibrated force; Cable jacket slitter matches scoring and stripping outer cable sheaths without penetrating internal conductor insulation; Heat shrink gun matches applying targeted hot air to shrink polyolefin tubing over completed terminations.

Each tool serves a dedicated role in cable preparation: the precision wire stripper removes insulation cleanly using gauge-matched openings, the ratcheting crimper cold-welds terminals to exposed strands with calibrated pressure, the cable jacket slitter safely strips outer sheaths without contacting internal insulation, and the heat shrink gun shrinks protective recovery tubing over finished terminations.

Adım Adım Çözüm

Identify the primary function of the precision wire stripper.

Matched with cutting through dielectric insulation at specific AWG gauges without nicking the metal core.

Wire strippers are manufactured with sized circular blades corresponding to American Wire Gauge (AWG) standards to shear only the plastic or rubber insulation jacket.

Identify the primary function of the ratcheting wire crimper.

Matched with compressing solderless lug barrels onto bare conductor strands with calibrated force.

Ratcheting mechanisms ensure terminal barrels undergo adequate plastic deformation without under-crimping or over-shearing the wire.

Identify the primary function of the cable jacket slitter.

Matched with scoring and stripping outer cable sheaths without penetrating internal conductor insulation.

Multi-conductor cables require an adjustable circumference or longitudinal blade that peels only the outer PVC or rubber jacket.

Identify the primary function of the heat shrink gun.

Matched with applying targeted hot air to shrink polyolefin tubing over completed terminations.

Controlled hot airflow radially shrinks recovery sleeves to provide environmental sealing, strain relief, and electrical insulation.

Anahtar Kavram

Selecting and applying specialized wire preparation tools to ensure reliable mechanical and electrical connections without damaging conductor strands or insulation layers.

Tahmini Süre:1m 0s

Soru 1277Soru →

During the assembly of an avionics chassis, a technician handles components made of various substances selected for their specific electrical transport properties. Arrange the following materials in order of their electrical resistivity at room temperature, from lowest resistivity (best conductor) to highest resistivity (best insulator).

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

Gold contact plating, followed by Intrinsic germanium crystal, followed by Porcelain standoff bushing

Gold contact plating is a metal with high electron mobility and the lowest resistivity. Intrinsic germanium is a semiconductor containing four valence electrons, providing an intermediate resistivity between conductors and non-conductors. Porcelain is a ceramic insulator whose valence electrons are tightly locked in ionic/covalent bonds, giving it the highest resistivity.

Adım Adım Çözüm

Classify each material according to its electrical conduction group (conductor, semiconductor, or insulator).

Gold is a conductor, germanium is a semiconductor, and porcelain is an insulator.

Electrical resistivity directly corresponds to how tightly a material's atomic structure holds its valence electrons.

Compare the relative electrical resistivities of the three material classifications.

Conductors have the lowest resistivity, semiconductors have moderate/intermediate resistivity, and insulators have the highest resistivity.

Resistivity is the inverse of conductivity; materials with abundant free electrons oppose current flow the least.

Sequence the items from lowest resistivity to highest resistivity.

Gold contact plating

\rightarrow

Intrinsic germanium crystal

\rightarrow

Porcelain standoff bushing.

Matching the classified items to the required ordering sequence satisfies the question criteria.

Anahtar Kavram

Classification of materials by electrical resistivity and atomic valence properties (conductors vs. semiconductors vs. insulators)

Tahmini Süre:1m 0s

Soru 1278Soru →

A technician needs to measure the electrical current flowing through a specific branch of a direct current (DC) circuit. How must the digital multimeter be connected into the circuit to obtain an accurate reading?

In parallel across the circuit load while the selector dial is set to direct-current voltage (DCV)

In series with the circuit branch so that the entire branch current passes through the meter

In parallel directly across the power supply terminals while set to the amperes range

In series with the circuit branch while the selector dial is set to alternating-current voltage (ACV)

Cevabı ve açıklamayı göster

Cevap: In series with the circuit branch so that the entire branch current passes through the meter

Cevap

In series with the circuit branch so that the entire branch current passes through the meter

Electrical current is the rate of electron flow through a conductor. To measure current, the circuit loop must be broken and the digital multimeter inserted in series so that all electrons traveling through that branch pass directly through the meter's low-resistance sensing circuit.

Adım Adım Çözüm

Identify the electrical quantity being measured and its physical nature

Electric current is the continuous rate of charge flow through a closed conductive loop

Understanding that current is a flow through a conductor determines how the measuring instrument must be placed in the circuit

Determine the correct meter configuration and circuit connection

The circuit must be physically opened and the meter inserted in series (in line) with the load path

An ammeter possesses very low internal resistance and must form part of the conductive path so that all electrons pass through the meter without impeding normal operation

Anahtar Kavram

Series Ammeter Connection in DC Circuits

Tahmini Süre:45s

Soru 1279Soru →

Match each automotive starting and charging system component with its primary operational function.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Starter Solenoid matches mechanical pinion shifting and high-current circuit closure; Rectifier Bridge matches conversion of AC from stator windings into DC; Voltage Regulator matches modulation of rotor field current to stabilize system voltage; Overrunning Clutch matches protecting the starter motor from excessive engine back-drive speeds.

Each component is accurately paired with its distinct physical and electrical duty: the starter solenoid engages the drive pinion and bridges heavy battery terminals; the rectifier bridge converts 3-phase AC into DC using diodes; the voltage regulator modulates rotor field current to maintain charging voltage within specification; and the overrunning clutch permits one-way torque transfer to prevent the running engine from damaging the starter armature.

Adım Adım Çözüm

Analyze the operational role of the starter solenoid

The starter solenoid acts as a heavy-duty relay and actuator, pulling the drive lever to engage the pinion gear into the ring gear while bridging battery terminal posts to spin the starter motor.

Identifies the dual electromechanical function distinguishing the solenoid from standard switches.

Analyze the operational role of the rectifier bridge

The rectifier uses positive and negative diode pairings to redirect bidirectional AC induced in stator loops into unidirectional DC.

Differentiates rectification (AC to DC conversion) from voltage regulation.

Analyze the operational role of the voltage regulator

The regulator monitors battery voltage and regulates system output by modulating current flow through the spinning rotor field coils via pulse-width switching or analog control.

Ensures electrical components are protected from overvoltage while keeping the battery adequately charged.

Analyze the operational role of the overrunning clutch

The overrunning clutch locks under starter-driven torque to crank the engine flywheel but disengages into a freewheeling state when the engine starts and spins faster than the starter pinion.

Prevents catastrophic centrifugal damage to the starter armature windings.

Anahtar Kavram

Electromechanical functions, voltage control, rectification, and mechanical safety drives in automotive starting and charging circuits

Tahmini Süre:2m 0s

Soru 1280Soru →

A passenger vehicle enters a sharp turn, initiating lateral chassis lean. Arrange the mechanical steps in the correct sequence to describe how the suspension stabilizer (sway) bar acts to counter this body roll.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence begins with lateral body roll during a turn, followed by the upward compression of the outer suspension linkage, the torsional twisting of the stabilizer bar across its frame mounts, and finally the transfer of torsional resistance to lift the inner control arm and level the vehicle.

A stabilizer (sway) bar functions as a transverse torsion spring. When a vehicle enters a turn, centrifugal force rolls the chassis outward. This compresses the outer wheel suspension, forcing its control arm and end link upward. This vertical motion twists the transverse bar along its mounting axis on the subframe. The resulting torsional resistance transfers mechanical force to pull the inside control arm upward, equalizing suspension deflection and keeping the chassis level.

Adım Adım Çözüm

Identify the primary kinematic trigger acting on the suspension.

Cornering inertia causes the vehicle chassis to roll toward the outside of the curve.

The stabilizer bar remains inactive when both wheels move together over uniform bumps; it requires differential suspension movement (body lean) to engage.

Determine the resulting motion at the loaded wheel assembly.

The outside suspension compresses, driving the outer lower control arm and its connected stabilizer end link upward.

The end link translates the relative vertical displacement of the control arm directly into the outer arm of the stabilizer bar.

Trace the mechanical force through the stabilizer bar assembly.

The central transverse bar section twists within its rubber or polyurethane pivot bushings.

Because the vehicle frame is rotating relative to the compressed control arm, the stabilizer bar undergoes elastic torsional deformation.

Determine the resulting counter-force on the opposite suspension corner.

The torsional resistance pulls upward on the inside control arm and pushes downward on the outside chassis side, resisting excessive lean.

The spring steel bar attempts to return to its untwisted state, effectively transferring roll stiffness across both sides of the axle.

Anahtar Kavram

Stabilizer Bar Kinematics and Torsional Resistance

Tahmini Süre:1m 15s

ÖncekiSayfa 64 / 261Sonraki

Tüm alıştırma soruları

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram