Tüm alıştırma soruları

3551 soru

Tüm türler3,551 Çoktan seçmeli1,809 Çoklu seçim786 Sayısal12 Eşleştirme521 Sıralama423

A technician is assembling a new desktop PC and needs to connect the computer case's power button, reset switch, and drive activity LEDs to the motherboard. Which of the following motherboard headers should the technician connect these chassis cables to?

Front panel header

24-pin ATX main power connector

SO-DIMM slot

PCIe x16 slot

Cevabı ve açıklamayı göster

Cevap: Front panel header

Cevap

The front panel header is used to connect the chassis power button, reset switch, and activity LEDs to the motherboard.

The front panel header (commonly designated as F_PANEL or PANEL on the motherboard) consists of a group of small pins that connect to the computer case's power switch, reset switch, hard drive activity LED, and power LED.

Adım Adım Çözüm

Identify the purpose of chassis wires

The wires originating from the PC enclosure connect to switches (power, reset) and LEDs (HDD, Power LED).

These controls allow the user to control power states and monitor system drive activity from the front of the computer case.

Locate the correct motherboard connector group

The motherboard provides a block of small pin connectors designated as the front panel header (or F_PANEL).

Matching the small wire leads (+/- polarity for LEDs and standard pin pairs for momentary switches) to the front panel pinout grid completes the connection.

Anahtar Kavram

Motherboard Headers and Front Panel Connections

Soru 3422Soru →

A technician is troubleshooting network connectivity on a desktop computer connected to an enterprise local area network. The host can successfully ping other computers on the local subnet ( $10.20.4.0/24$ ), but users cannot access resources on remote subnets or reach internet services. Pinging an external address such as $8.8.8.8$ results in a "Destination host unreachable" error message.

Executing `ipconfig /all` on the workstation displays the following network configuration parameters:

Parameter	Configured Value
IPv4 Address	$10.20.4.78$
Subnet Mask	$255.255.255.0$
Default Gateway	$10.20.5.1$
DNS Server	$10.20.4.2$

Which of the following configuration errors is the primary cause of the external connectivity issue?

The default gateway IP address resides on a different IP subnet than the workstation.

The workstation failed to acquire a DHCP lease and automatically assigned itself an APIPA address.

The DNS server address is acting as a DHCP server and refusing to resolve default gateway hostnames.

The local unmanaged Layer 2 switch is improperly configured to route packets between subnets.

Cevabı ve açıklamayı göster

Cevap: The default gateway IP address resides on a different IP subnet than the workstation.

Cevap

The default gateway IP address resides on a different IP subnet than the workstation.

With a subnet mask of

255.255.255.0

, all devices on the local subnet must have IP addresses starting with

10.20.4

. The gateway address

10.20.5.1

is on a different subnet (

10.20.5.0/24

), making it unreachable directly by the workstation. Without a valid local default gateway, traffic targeting outside IP addresses (such as

8.8.8.8

) cannot be routed off the local network.

Adım Adım Çözüm

Analyze host IPv4 network address and subnet bounds

10.20.4.78

with mask

255.255.255.0

(

/24

) means local network valid host range is

10.20.4.1

through

10.20.4.254

Subnet mask

255.255.255.0

restricts local communication to IP addresses matching the first three octets (

10.20.4.x

Compare Default Gateway address to local network bounds

The configured default gateway is

10.20.5.1

, which belongs to the

10.20.5.0/24

network subnet.

For a client to forward packets outside its local network, its default gateway must be a reachable router interface located on the exact same local IP subnet.

Determine root cause of failure

Local traffic succeeds, but remote traffic fails because the gateway is unreachable due to a subnet mismatch.

Re-assigning the default gateway to an address in the

10.20.4.0/24

range (e.g.,

10.20.4.1

) will restore external connectivity.

Anahtar Kavram

IP Subnetting and Default Gateway Assignment

Tahmini Süre:1m 15s

Soru 3423Soru →

A user reports that the screen on a company-issued laptop is completely dark, though an external monitor functions normally. A technician suspects a faulty backlight inverter board and orders a replacement part. Upon inspecting the system specifications, the technician notes that the laptop is equipped with an Organic Light-Emitting Diode (OLED) display. Which of the following explains why ordering an inverter board was incorrect for this laptop?

OLED panels feature self-emissive pixels and do not utilize a backlight or inverter board.

OLED panels use Cold Cathode Fluorescent Lamps (CCFL) that draw power directly from the system motherboard.

The display inverter in an OLED panel is integrated into the graphics processing unit (GPU) rather than the display bezel.

OLED screen illumination is managed entirely by software display drivers rather than hardware power components.

Cevabı ve açıklamayı göster

Cevap: OLED panels feature self-emissive pixels and do not utilize a backlight or inverter board.

Cevap

OLED panels feature self-emissive pixels and do not utilize a backlight or inverter board.

The correct option explains that OLED (Organic Light-Emitting Diode) displays utilize self-emissive pixels. Each subpixel produces its own light when electric current is applied, removing the need for a separate backlight unit or an inverter board. Inverters are used exclusively in displays with Cold Cathode Fluorescent Lamp (CCFL) backlighting to convert low-voltage DC power from the motherboard into high-voltage AC power.

Adım Adım Çözüm

Identify the display panel technology used in the laptop.

The laptop uses an OLED (Organic Light-Emitting Diode) panel.

Display components vary significantly based on whether the panel is traditional LCD (LED/CCFL-backlit) or OLED.

Determine the power and illumination requirements of OLED technology.

OLED pixels are self-emissive, generating light individually when energized.

Because each pixel emits light, OLED displays do not require a backlight layer or an inverter to convert DC power to high-voltage AC.

Evaluate why replacing an inverter board is unnecessary.

An inverter board does not exist in an OLED display assembly.

Inverters are only present in older CCFL-backlit LCD displays.

Anahtar Kavram

OLED Display Architecture and Component Requirements

Tahmini Süre:1m 0s

Soru 3424Soru →

Match each expansion card interface specification or power supply unit (PSU) connector on the left with its correct functional characteristic or operational limit on the right.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

The EPS12V 8-pin connector pairs with dedicated CPU VRM power; the PCIe 6+2 pin auxiliary connector delivers up to

150\text{ W}

to graphics cards; the mechanical PCIe x16 (electrical x4) slot accommodates full-length cards while capping throughput to 4 data lanes; and the standard PCIe slot delivers up to

75\text{ W}

directly through motherboard pins.

Each connector and expansion slot is paired according to its standard specifications: EPS12V handles dedicated CPU socket power, PCIe 6+2 pin supplies up to

150\text{ W}

auxiliary GPU power, mechanical x16 / electrical x4 slots cap bandwidth to 4 lanes, and standard PCIe bus slots provide up to

75\text{ W}

direct pin power.

Adım Adım Çözüm

Differentiate CPU motherboard power connectors from auxiliary expansion card power connectors.

Identify that the EPS12V 8-pin connector is wired and keyed specifically for processor power phases on the motherboard, whereas PCIe 6+2 connectors are keyed for expansion cards.

Connecting EPS12V cables to GPU auxiliary sockets or vice-versa causes severe hardware damage due to opposing

+12\text{ V}

and Ground pin layouts.

Distinguish power delivery thresholds between motherboard slots and discrete cables.

Note that standard PCIe slots supply up to

75\text{ W}

via slot pins, while an 8-pin (or 6+2 pin) auxiliary PCIe cable supplies up to

150\text{ W}

High-TDP graphics cards require combined wattage from both the motherboard slot (

75\text{ W}

) and one or more auxiliary cables.

Analyze mechanical versus electrical lane allocation constraints on expansion slots.

Recognize that mechanical size determines card physical compatibility, while electrical wiring determines data trace bandwidth.

Motherboard manufacturers route secondary x16 physical slots with fewer electrical lanes (such as x4) to conserve chipset/CPU PCIe lane budgets.

Anahtar Kavram

Power supply connector pinouts, wattage ratings, and PCIe slot lane/power specifications

Soru 3425Soru →

A network technician is deploying new Wi-Fi 6 (IEEE 802.11ax) access points in a large conference hall to accommodate high-density user connections. Which of the following features supported by the IEEE 802.11ax standard directly increase transmission efficiency and capacity in high-density wireless environments? (Select TWO).

Geçerli olan tümünü seçin

OFDMA (Orthogonal Frequency Division Multiple Access) to split channels into smaller resource units for simultaneous multi-user transmissions

Bi-directional (uplink and downlink) MU-MIMO support across both 2.4 GHz and 5 GHz frequency bands

Mandatory channel configuration utilizing adjacent channels 2, 7, and 12 to maximize 2.4 GHz bandwidth

Exclusive operation solely within the 5 GHz spectrum to eliminate legacy 2.4 GHz client compatibility

Cevabı ve açıklamayı göster

Cevap: OFDMA (Orthogonal Frequency Division Multiple Access) to split channels into smaller resource units for simultaneous multi-user transmissions; Bi-directional (uplink and downlink) MU-MIMO support across both 2.4 GHz and 5 GHz frequency bands

Cevap

The correct selections are OFDMA for dividing channels into smaller resource units and bi-directional MU-MIMO across both 2.4 GHz and 5 GHz bands.

IEEE 802.11ax (Wi-Fi 6) addresses high-density environments primarily through OFDMA (Orthogonal Frequency Division Multiple Access), which divides channels into smaller resource units to serve multiple devices concurrently, and bi-directional MU-MIMO, which allows simultaneous uplink and downlink data transfers across both 2.4 GHz and 5 GHz bands.

Adım Adım Çözüm

Identify the key capabilities introduced in IEEE 802.11ax (Wi-Fi 6) aimed at high client density.

Recognize that Wi-Fi 6 incorporates OFDMA and expanded bi-directional MU-MIMO.

OFDMA allocates smaller sub-channels (resource units) to different clients simultaneously, reducing latency and contention in crowded environments.

Evaluate the spectrum operation of IEEE 802.11ax.

Confirm 802.11ax operates on both 2.4 GHz and 5 GHz (unlike 802.11ac which operated exclusively on 5 GHz).

Operating across both bands allows 802.11ax to enhance speed and efficiency for 2.4 GHz legacy devices while leveraging 5 GHz channels.

Eliminate incorrect wireless spectrum configuration claims.

Reject the option specifying channels 2, 7, and 12, as well as the option claiming 5 GHz exclusivity.

Standard 2.4 GHz non-overlapping channels are 1, 6, and 11, and 802.11ax is not restricted solely to 5 GHz.

Anahtar Kavram

IEEE 802.11ax (Wi-Fi 6) Wireless Standards & High-Density Enhancements

Soru 3426Soru →

A network administrator is establishing security rules on an internal subnet router to support legacy macOS workstations accessing a centralized file server using Apple Filing Protocol (AFP). Which of the following ports should the administrator permit through the router to ensure proper AFP communication?

TCP port 548

TCP port 445

TCP port 427

TCP port 389

Cevabı ve açıklamayı göster

Cevap: TCP port 548

Cevap

TCP port 548 is required to allow Apple Filing Protocol (AFP) network communication.

Apple Filing Protocol (AFP) operates over TCP port 548 to enable file management and sharing capabilities across local networks for macOS systems.

Adım Adım Çözüm

Identify the target protocol required for network file access in the given scenario.

The scenario specifically asks for the port associated with Apple Filing Protocol (AFP).

Understanding protocol requirements is necessary to configure firewall access control lists correctly.

Map Apple Filing Protocol (AFP) to its standard TCP/IP port assignment.

AFP operates over TCP port 548.

Standard network protocols use default well-known ports defined by IANA.

Anahtar Kavram

Standard Network Port Assignments for File Transfer Protocols (AFP vs SMB)

Tahmini Süre:1m 0s

Soru 3427Soru →

A systems administrator is configuring a central Windows print server to share a newly installed enterprise multifunction device (MFD). The environment consists of 64-bit Windows 11 desktop computers and legacy 32-bit Windows industrial workstations. After installing the 64-bit printer driver on the server and sharing the printer, users on 64-bit workstations can successfully connect and print, but users on 32-bit workstations receive an error stating that a compatible driver could not be found. Which printer configuration step should the administrator perform on the print server to resolve this issue?

Add the 32-bit (x86) driver under the Additional Drivers settings in the shared printer properties on the print server.

Change the print server port configuration from a Standard TCP/IP Port to an LPR/LPD legacy port mapping.

Reconfigure the network DHCP server options to assign 32-bit client reservation scopes to the MFD network interface.

Replace the network switch servicing the legacy workstation subnet with a Layer 3 router to handle 32-bit traffic translation.

Cevabı ve açıklamayı göster

Cevap: Add the 32-bit (x86) driver under the Additional Drivers settings in the shared printer properties on the print server.

Cevap

Add the 32-bit (x86) driver under the Additional Drivers settings in the shared printer properties on the print server.

The correct option is adding the 32-bit (x86) driver under the Additional Drivers section of the print server's shared printer properties. When hosting a shared printer on a 64-bit server, 32-bit client computers cannot use the server's native 64-bit driver. Windows print servers accommodate heterogeneous client environments by allowing administrators to upload additional driver packages (x86), which are then automatically served to matching clients when they connect to the shared printer queue.

Adım Adım Çözüm

Analyze the reported symptom and system environment.

Identified that 64-bit clients print successfully while 32-bit clients fail due to missing compatible architecture drivers on the central print server.

When a Windows client connects to a network shared printer, it downloads the driver directly from the server. If the server only hosts a 64-bit driver, 32-bit clients cannot load it.

Determine the necessary configuration change on the Windows print server.

Access the Printer Properties -> Sharing tab -> Additional Drivers button on the server.

This allows administrators to stage x86 (32-bit) driver binaries alongside existing x64 (64-bit) drivers.

Verify client connection mechanism.

32-bit clients automatically download and install the provided x86 driver from the server upon connecting to the shared queue.

Centralizing drivers on the print server ensures seamless point-and-print deployment without requiring manual local driver installations on every 32-bit workstation.

Anahtar Kavram

Windows Print Server Additional Drivers Configuration (x86 vs x64)

Soru 3428Soru →

A technician is configuring a newly installed network printer on a local office network. To ensure that client computers can consistently reach the printer even after network router restarts, which configuration change should be applied to the printer's network settings?

Assign a static IP address or configure a DHCP reservation for the printer.

Configure the printer to rely on APIPA addressing for dynamic IP assignment.

Configure the DNS server to automatically lease IP addresses to network devices.

Set the network print port setting to port 80 to encrypt print job traffic.

Cevabı ve açıklamayı göster

Cevap: Assign a static IP address or configure a DHCP reservation for the printer.

Cevap

Assigning a static IP address or setting a DHCP reservation ensures that the printer retains a constant IP address, preserving connectivity for network clients.

Assigning a static IP address or creating a DHCP reservation guarantees that the printer always receives the same IP address on the network. This ensures client computers configured to print to that IP address will not lose connectivity when the router reboots or leases expire.

Adım Adım Çözüm

Identify the network requirement

Network printers require a persistent IP address so client printing ports do not lose connection when IP leases change.

If a printer uses standard dynamic DHCP leasing, a router reboot could reassign a different IP address, breaking existing printer connections on client workstations.

Select the appropriate network configuration method

Configure either a static IP address directly on the printer or a MAC-based DHCP reservation on the network router/server.

Both methods guarantee that the printer's IP address remains unchanged across reboots and lease renewals.

Anahtar Kavram

Static IP and DHCP Reservation for Network Printers

Soru 3429Soru →

A technician is evaluating motherboard form factor specifications to select a suitable replacement board for a desktop chassis that requires backwards compatibility with existing ATX mounting points and rear I/O shield cutouts while fitting inside a smaller enclosure. Which of the following statements correctly describe the design specifications and motherboard connector features of the microATX form factor compared to standard ATX? (Select TWO.)

Geçerli olan tümünü seçin

MicroATX motherboards feature maximum physical dimensions of

9.6 \times 9.6\text{ inches}

(

244 \times 244\text{ mm}

) and typically accommodate a maximum of four expansion slots.

MicroATX motherboards share top mounting hole alignment pattern points and standard rear I/O panel dimensions with full-size ATX motherboards.

MicroATX motherboards mandate the use of small-outline dual in-line memory modules (SO-DIMMs) to conserve printed circuit board surface space.

MicroATX motherboards replace the standard 24-pin ATX main power header with a proprietary 14-pin motherboard power interface.

Cevabı ve açıklamayı göster

Cevap: MicroATX motherboards feature maximum physical dimensions of $9.6 \times 9.6\text{ inches}$ ( $244 \times 244\text{ mm}$ ) and typically accommodate a maximum of four expansion slots.; MicroATX motherboards share top mounting hole alignment pattern points and standard rear I/O panel dimensions with full-size ATX motherboards.

Cevap

The microATX form factor specifies maximum dimensions of

9.6 \times 9.6\text{ inches}

(

244 \times 244\text{ mm}

) supporting up to four expansion slots, and maintains backwards compatibility by sharing top mounting hole positions and rear I/O shield dimensions with standard ATX chassis.

The microATX specification defines a maximum board size of

9.6 \times 9.6\text{ inches}

(

244 \times 244\text{ mm}

) with up to 4 expansion slots. Additionally, microATX was engineered to be backward compatible with ATX chassis by retaining the same top standoff mounting locations and standard rear I/O panel layout.

Adım Adım Çözüm

Identify physical dimensions and slot limitations of microATX

MicroATX boards are defined up to

9.6 \times 9.6\text{ inches}

(

244 \times 244\text{ mm}

) with a maximum of 4 expansion slots.

Standard ATX measures up to

12 \times 9.6\text{ inches}

with up to 7 slots, whereas microATX reduces height while retaining width.

Verify mechanical layout and chassis compatibility rules

MicroATX boards align with standard ATX top standoff mounting holes and use identical rear I/O panel dimensions.

This backward compatibility allows microATX boards to mount directly into standard ATX cases.

Evaluate memory and power interface standards

MicroATX uses standard 24-pin ATX main power connectors and full-size desktop DIMM slots.

Proprietary headers or laptop memory form factors (SO-DIMMs) are not part of the standard microATX specification.

Anahtar Kavram

Motherboard Form Factors and Compatibility Standards (microATX vs ATX)

Soru 3430Soru →

A technician is installing replacement solid-state storage into a desktop system. The motherboard technical manual specifies that M.2 Slot 1 is M-key only and connected directly to four PCIe 4.0 lanes, while M.2 Slot 2 is B-key only and wired through the SATA controller and two PCIe 3.0 lanes. Which of the following statements correctly describe the compatibility and performance characteristics of these slots? (Select TWO.)

Geçerli olan tümünü seçin

An M.2 NVMe SSD with a single M-key notch can be installed in Slot 1, but it will be physically blocked from fully inserting into Slot 2.

An M.2 SATA SSD installed in Slot 2 will be capped at standard SATA III maximum transfer rates of 6 Gbps despite being in an M.2 form factor.

An M.2 SATA SSD installed in Slot 1 will automatically upgrade to NVMe throughput speeds because the slot connects directly to PCIe lanes.

Installing an M.2 drive with a dual B&M-key edge connector into Slot 2 guarantees PCIe 3.0 x2 NVMe speed performance.

Cevabı ve açıklamayı göster

Cevap: An M.2 NVMe SSD with a single M-key notch can be installed in Slot 1, but it will be physically blocked from fully inserting into Slot 2.; An M.2 SATA SSD installed in Slot 2 will be capped at standard SATA III maximum transfer rates of 6 Gbps despite being in an M.2 form factor.

Cevap

An M.2 NVMe SSD with an M-key notch will physically fit into Slot 1 but not Slot 2, and an M.2 SATA SSD in Slot 2 will remain limited to 6 Gbps SATA III speeds.

Physical M-key drive connectors prevent mechanical insertion into B-key slots. Furthermore, M.2 drives utilizing the SATA protocol remain constrained by SATA III 6 Gbps speed limitations regardless of the M.2 connector interface.

Adım Adım Çözüm

Analyze physical keying constraints for M.2 SSD slots and connectors.

M-key drives have a notch at pins 59–66 and only fit into M-key sockets. B-key slots have a ridge at pins 12–19, physically blocking M-key-only NVMe drives.

Physical keying prevents users from inserting drives into slots that do not supply the required electrical signals or bus interfaces.

Determine protocol limits vs physical form factor capabilities.

An M.2 SATA drive utilizes the SATA III bus standard, which is capped at a maximum throughput of 6 Gbps (roughly 550-600 MB/s), regardless of using an M.2 slot.

Form factor (M.2) does not dictate speed; speed is defined by the underlying bus protocol (SATA vs NVMe/PCIe).

Anahtar Kavram

Distinction between M.2 physical keying (B-Key vs M-Key) and bus protocols (SATA vs PCIe/NVMe)

Soru 3431Soru →

Match each storage drive interface standard with its corresponding physical, protocol, or performance specification.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

M.2 NVMe SSD matches the high-speed PCIe bus interface; SATA III 2.5-inch SSD matches the

6\text{ Gbps}

AHCI serial bus interface; SAS Drive matches the enterprise dual-port

12\text{ Gbps}

interface; and eSATA Drive matches the shielded external native SATA cable standard.

Each storage interface matches its distinct protocol, bus throughput limit, and intended application: M.2 NVMe connects over PCIe for extreme throughput (

3,000+\text{ MB/s}

); SATA III uses AHCI for

6\text{ Gbps}

internal storage; SAS serves enterprise chassis with dual-port

12\text{ Gbps}+

signaling; and eSATA provides

6\text{ Gbps}

native SATA connectivity externally via shielded cables.

Adım Adım Çözüm

Identify the protocol and bus topology for M.2 NVMe.

NVMe utilizes PCI Express (PCIe) lanes directly, delivering transfer rates far exceeding SATA limits (

3,000+\text{ MB/s}

NVMe is engineered specifically for non-volatile solid-state memory over PCIe.

Identify the bandwidth limits for SATA III 2.5-inch drives.

SATA III operates using AHCI at a theoretical max speed of

6\text{ Gbps}

(

600\text{ MB/s}

Standard desktop SATA III internal storage interfaces are capped at

6\text{ Gbps}

Analyze enterprise SAS drive characteristics.

SAS provides dual-port connectivity and enterprise reliability with speeds reaching

12\text{ Gbps}

or higher.

SAS controllers accommodate dual-port high-availability server backplanes.

Differentiate external SATA (eSATA) from internal interface standards.

eSATA allows external enclosures to connect directly to the system SATA controller using shielded cables up to

6\text{ Gbps}

eSATA avoids protocol translation penalties inherent in legacy USB-to-SATA adapters.

Anahtar Kavram

Storage Interface Standards and Bus Protocols

Soru 3432Soru →

A technician is reviewing power delivery specifications for a desktop PC motherboard replacement. Which of the following power connectors are standard components designed to provide power directly to modern desktop motherboards and their onboard components? (Select TWO.)

Geçerli olan tümünü seçin

24-pin ATX main power connector

8-pin EPS/CPU power connector

SO-DIMM power bridge header

M.2 SATA key power cable

Cevabı ve açıklamayı göster

Cevap: 24-pin ATX main power connector; 8-pin EPS/CPU power connector

Cevap

The correct motherboard power connectors are the 24-pin ATX main power connector and the 8-pin EPS/CPU power connector.

Standard desktop motherboards utilize a 24-pin ATX connector as their primary power source and an 8-pin (or 4-pin) EPS/CPU connector to supply dedicated power to the processor.

Adım Adım Çözüm

Identify main power requirements for ATX motherboards

Recognize that standard desktop motherboards require a main 24-pin P1 connector to power chipset, expansion buses, and onboard logic.

The 24-pin ATX main connector provides the primary DC voltage rails (+3.3V, +5V, +12V) needed for general motherboard operations.

Identify auxiliary CPU power delivery requirements

Recognize that dedicated CPU power is delivered via a 4-pin or 8-pin EPS/CPU power connector located near the CPU socket.

Modern CPUs demand dedicated +12V power conditioning separate from the main motherboard 24-pin connector.

Anahtar Kavram

Motherboard Power Connectors (ATX 24-pin and EPS12V)

Soru 3433Soru →

A system administrator is deploying a high-volume multifunction device (MFD) for a corporate department. Security policy mandates that users must scan documents directly to their network home drives over the local network using their domain credentials, and all print jobs must be tracked for auditing purposes by individual user account. Which TWO of the following configurations should the administrator implement to meet these requirements?

Geçerli olan tümünü seçin

Configure Scan to SMB using Active Directory authentication

Enable print accounting and user authentication on the MFD and print queue

Configure POP3 service settings on the printer to deposit scanned files onto network shares

Assign a static APIPA address to the MFD to ensure permanent connectivity to domain servers

Connect the MFD to an unmanaged Layer 2 switch to route scan traffic between different subnets

Cevabı ve açıklamayı göster

Cevap: Configure Scan to SMB using Active Directory authentication; Enable print accounting and user authentication on the MFD and print queue

Cevap

The correct configurations are configuring Scan to SMB using Active Directory authentication and enabling print accounting and user authentication on the MFD and print queue.

Configuring Scan to SMB allows users to deliver scanned files straight to network shares using their corporate directory accounts. Activating user authentication and print accounting ensures every print job is associated with a specific user account for tracking and audit logs.

Adım Adım Çözüm

Identify the requirement for direct-to-folder network scanning using domain credentials.

Scan to SMB integrated with Active Directory allows authenticated users to transmit scans directly into their respective network file paths.

SMB is the standard protocol for accessing network shares and home drives in a Windows corporate environment.

Identify the requirement for tracking and auditing print usage per user.

Enabling user authentication (via PIN, badge, or domain credentials) along with print accounting on the device and server records usage per account.

Accounting logs provide administrative metrics and security auditing for all print, copy, and scan activities.

Anahtar Kavram

Multifunction Device Network Integration and Security Configuration

Soru 3434Soru →

A network technician is terminating custom Category 6 unshielded twisted-pair (UTP) Ethernet cables to connect client desktop computers to wall jacks. The existing network infrastructure strictly adheres to the ANSI/TIA-568B wiring standard across all patch panels and wall outlets. Which of the following requirements must the technician follow to ensure proper physical layer connectivity for these straight-through connections? (Select TWO)

Geçerli olan tümünü seçin

Terminate both ends of each cable using the T568B color coding sequence.

Position the white/orange wire at Pin 1 and the solid orange wire at Pin 2 of the RJ45 connector.

Terminate one end using T568A and the opposite end using T568B to enable switch communication.

Position the white/green wire at Pin 1 and the solid green wire at Pin 2 of the RJ45 connector.

Cevabı ve açıklamayı göster

Cevap: Terminate both ends of each cable using the T568B color coding sequence.; Position the white/orange wire at Pin 1 and the solid orange wire at Pin 2 of the RJ45 connector.

Cevap

The correct requirements are to terminate both ends of each cable using the T568B color sequence and to place the white/orange wire at Pin 1 and the solid orange wire at Pin 2.

For a standard workstation-to-switch connection in an environment standardized on ANSI/TIA-568B, straight-through cables must be used. This requires terminating both ends with the T568B scheme, where Pin 1 is white/orange and Pin 2 is solid orange.

Adım Adım Çözüm

Identify the cable type required for host-to-switch connections.

Connecting an end-user desktop workstation to a network wall jack requires a straight-through Ethernet cable.

Straight-through cables require identical wiring standards on both ends of the cable link.

Determine the pinout assignment for the specified ANSI/TIA-568B standard.

T568B pinout order for pins 1 through 8 is: 1 (White/Orange), 2 (Orange), 3 (White/Green), 4 (Blue), 5 (White/Blue), 6 (Green), 7 (White/Brown), 8 (Brown).

Matching existing infrastructure standards prevents split pairs and physical line mismatches.

Anahtar Kavram

T568A and T568B Ethernet Wiring Pinout Standards

Soru 3435Soru →

A field technician is deploying a workstation dock connected to a laptop's host port labeled with a Thunderbolt 4 icon. Which of the following capabilities and underlying protocols are natively supported by the Thunderbolt 4 specification over its USB Type-C physical connector? (Select TWO.)

Geçerli olan tümünü seçin

PCI Express (PCIe) data tunneling for external storage drive arrays and expansion chassis

DisplayPort Alternate Mode for driving external high-resolution digital video monitors directly

Native RS-232 serial bus signaling without using an active serial protocol converter

Direct analog VGA RGB video transmission over passive physical adapter wiring

Cevabı ve açıklamayı göster

Cevap: PCI Express (PCIe) data tunneling for external storage drive arrays and expansion chassis; DisplayPort Alternate Mode for driving external high-resolution digital video monitors directly

Cevap

Thunderbolt 4 natively supports PCI Express (PCIe) bus tunneling for high-speed peripherals and DisplayPort Alternate Mode for direct digital video output over a physical USB Type-C connector.

Thunderbolt 4 built upon the USB Type-C connector specification natively encapsulates PCIe data packets (allowing direct host bus performance for external drives and docking stations) and supports DisplayPort Alternate Mode (delivering uncompressed digital video to external monitors). Both features function without needing active protocol translation chipsets.

Adım Adım Çözüm

Identify the physical connector and underlying interface protocol standard specified in the scenario.

The scenario specifies a Thunderbolt 4 controller operating through a USB Type-C physical port.

Thunderbolt 4 standardizes specific native data and video protocols that can be multiplexed over the USB Type-C cable assembly.

Evaluate the supported native protocols against the provided options.

Thunderbolt 4 mandates PCIe data tunneling (up to 32 Gbps PCIe data throughput) and native DisplayPort Alternate Mode for dual 4K or single 8K displays.

These capabilities allow high-speed external peripheral access and multi-monitor display outputs without external protocol conversion cards.

Filter out invalid legacy or analog signaling assumptions.

RS-232 serial and analog VGA are not supported natively and require active translation adapters.

USB-C and Thunderbolt interfaces handle modern digital packets, lacking legacy analog video DAC pinouts or direct serial UART lines.

Anahtar Kavram

Thunderbolt 4 Protocol Tunneling and USB-C Alternate Modes

Tahmini Süre:1m 30s

Soru 3436Soru →

A technician is configuring a static IP network profile for a desktop workstation on a corporate network segment ( $10.15.4.0/24$ ). The workstation can successfully ping local hosts on $10.15.4.0/24$ , but cannot access external websites or ping servers on adjacent subnets. Running `ipconfig /all` displays the following settings:

- IP Address: $10.15.4.50$
- Subnet Mask: $255.255.255.0$
- Default Gateway: $10.15.5.1$
- Preferred DNS Server: $10.15.4.2$

Which of the following statements accurately explain why off-subnet network traffic is failing? (Select TWO.)

Geçerli olan tümünü seçin

The default gateway address is assigned to a different logical subnet than the host workstation.

The workstation cannot resolve the MAC address of the default gateway via ARP because the gateway is outside the local broadcast domain.

The host workstation has automatically defaulted to an APIPA configuration due to a failed DHCP lease request.

The DNS server is misconfigured to lease dynamic IP addresses rather than performing hostname resolution.

Cevabı ve açıklamayı göster

Cevap: The default gateway address is assigned to a different logical subnet than the host workstation.; The workstation cannot resolve the MAC address of the default gateway via ARP because the gateway is outside the local broadcast domain.

Cevap

Remote connectivity fails because the default gateway (

10.15.5.1

) is assigned to a different IP subnet than the host (

10.15.4.50/24

), preventing the host from using local Address Resolution Protocol (ARP) to reach its gateway.

For a host to communicate with remote networks, its default gateway must be located on the same local IP subnet. With host address

10.15.4.50

and subnet mask

255.255.255.0

, the gateway must reside within the

10.15.4.1

–

10.15.4.254

range. Because the gateway is configured as

10.15.5.1

, it sits outside the host's local subnet. As a result, the workstation's ARP requests for

10.15.5.1

will go unanswered, preventing off-subnet packet encapsulation.

Adım Adım Çözüm

Analyze the host IP address and subnet mask.

IP Address

10.15.4.50

with Subnet Mask

255.255.255.0

defines the local network segment as

10.15.4.0/24

(usable host range

10.15.4.1

10.15.4.254

Determines the boundaries of the host's local broadcast domain.

Evaluate the configured default gateway address.

Default Gateway is configured as

10.15.5.1

, which belongs to the

10.15.5.0/24

subnet.

A host must send traffic to its local gateway's MAC address to route off-subnet packets. Since

10.15.5.1

is on a different subnet, ARP broadcasts on

10.15.4.0/24

will not receive a reply from the router interface.

Anahtar Kavram

Default Gateway Subnet Assignment and ARP Resolution

Soru 3437Soru →

A technician is setting up a new network printer on a user's Windows workstation using the printer's static IP address. Place the steps for manually adding this network printer into the correct sequential order from first to last.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence starts with opening Printers & scanners to add a device, selecting that the printer isn't listed, specifying the printer's IP address to create the TCP/IP port, installing the appropriate manufacturer driver, and finally printing a test page to verify connectivity.

To manually install a network printer by IP address, a technician must first open Printers & scanners, opt out of automatic discovery, select the IP address addition method to create the network port, choose and load the matching driver, and finish by sending a test print to confirm functionality.

Adım Adım Çözüm

Open the Windows device management interface

Access the Printers & scanners settings menu.

This starts the wizard required to discover or configure new print devices.

Override automatic discovery

Bypass auto-scan by choosing 'The printer that I want isn't listed'.

Manual network parameter entry requires opting out of automated network scanning.

Configure the network target

Select adding via IP address/hostname and enter the printer's IP.

Creates a Standard TCP/IP port pointing directly to the printer's network interface.

Assign the print driver

Select the correct manufacturer and model driver.

Ensures the workstation can render print jobs in the printer's supported Page Description Language (PDL).

Validate installation

Print a test page.

Verifies end-to-end communication from software driver down to physical print output.

Anahtar Kavram

Standard TCP/IP Printer Installation Procedure

Tahmini Süre:1m 0s

Soru 3438Soru →

A network technician is configuring three wireless access points (APs) positioned along a hallway to cover a office floor using the 2.4 GHz band. Access Point 1 has been configured to use Channel 1. To prevent adjacent channel interference and maximize wireless performance, which non-overlapping channel assignment should the technician select for Access Point 2 and Access Point 3?

Channel 6 for Access Point 2 and Channel 11 for Access Point 3

Channel 2 for Access Point 2 and Channel 3 for Access Point 3

Channel 3 for Access Point 2 and Channel 7 for Access Point 3

Channel 4 for Access Point 2 and Channel 8 for Access Point 3

Cevabı ve açıklamayı göster

Cevap: Channel 6 for Access Point 2 and Channel 11 for Access Point 3

Cevap

The technician should assign Channel 6 to Access Point 2 and Channel 11 to Access Point 3.

In North America and standard international 2.4 GHz Wi-Fi deployments, channels 1, 6, and 11 are the primary 20 MHz non-overlapping channels. Configuring AP 1 on Channel 1, AP 2 on Channel 6, and AP 3 on Channel 11 ensures that signal coverage areas can border each other without suffering from adjacent-channel interference.

Adım Adım Çözüm

Identify the operating frequency band

The deployment uses the 2.4 GHz wireless spectrum.

The 2.4 GHz band has 11 to 14 available channels spaced 5 MHz apart, but standard channel width is 20 MHz.

Determine non-overlapping channels in the 2.4 GHz band

Channels 1, 6, and 11 are separated by 25 MHz (5 channels), which prevents frequency spectrum collision.

Any channel choice between 1, 6, and 11 causes adjacent channel interference.

Assign remaining non-overlapping channels

With AP 1 on Channel 1, AP 2 should be assigned Channel 6 and AP 3 should be assigned Channel 11.

This configuration maximizes throughput and eliminates adjacent-channel interference between adjacent access points.

Anahtar Kavram

2.4 GHz Wireless Non-Overlapping Channels

Tahmini Süre:1m 0s

Soru 3439Soru →

A desktop technician is assembling a high-performance workstation and configuring the CPU socket hardware along with a thermal cooling solution. Which of the following statements regarding CPU socket architectures and thermal cooling installation are correct? (Select TWO.)

Geçerli olan tümünü seçin

Land Grid Array (LGA) sockets feature pin contacts located inside the motherboard socket housing rather than on the processor package.

Thermal paste is applied between the processor heat spreader and the cooler baseplate to fill microscopic gaps and improve heat transfer.

Ball Grid Array (BGA) processors utilize zero insertion force (ZIF) socket levers to simplify frequent end-user processor upgrades.

Pin Grid Array (PGA) sockets require installing cooling fan headers directly to CPU pins prior to clamping the processor.

Cevabı ve açıklamayı göster

Cevap: Land Grid Array (LGA) sockets feature pin contacts located inside the motherboard socket housing rather than on the processor package.; Thermal paste is applied between the processor heat spreader and the cooler baseplate to fill microscopic gaps and improve heat transfer.

Cevap

Land Grid Array (LGA) sockets feature pin contacts located inside the motherboard socket housing rather than on the processor package, and thermal paste is applied between the processor heat spreader and the cooler baseplate to fill microscopic gaps and improve heat transfer.

Land Grid Array (LGA) sockets place the delicate contact pins on the motherboard socket, requiring CPUs to have matching flat contact pads. Additionally, applying thermal paste between the CPU integrated heat spreader and the cooling block baseplate fills microscopic air gaps, ensuring maximum thermal conductivity.

Adım Adım Çözüm

Analyze CPU socket physical characteristics for LGA, PGA, and BGA packaging types.

Identify that LGA sockets put pins on the motherboard socket and pads on the CPU, whereas BGA CPUs are soldered and PGA CPUs have pins on the chip package.

Understanding socket mechanical construction is essential for safe handling during installation.

Evaluate thermal management components and proper thermal compound placement.

Confirm that thermal paste eliminates air pockets between the processor IHS and the cooling block.

Air is a poor thermal conductor; thermal paste ensures efficient heat conduction to preventing thermal throttling.

Anahtar Kavram

CPU packaging socket types (LGA, PGA, BGA) and thermal interface material function

Soru 3440Soru →

A field technician connects a high-speed external storage enclosure requiring Thunderbolt protocol capabilities to a newly deployed tablet using a verified high-speed USB Type-C cable. Although the enclosure powers on and mounts successfully, data transfers are capped at legacy USB speeds ( $480\text{ Mbps}$ ). Which of the following best explains why the connection fails to achieve Thunderbolt transfer rates?

The tablet's physical USB Type-C port is internally wired only for USB 2.0 signals and lacks host controller hardware support for Thunderbolt.

Because all physical USB Type-C ports inherently support Thunderbolt protocols, the reduced speed indicates an active Mobile Device Management (MDM) bandwidth throttle policy.

The tablet requires a cellular SIM card provisioned with a matching IMSI to authenticate high-speed external bus operations.

The throughput drop occurs because the tablet is attempting to transfer data using an IMAP synchronization protocol instead of direct bus access.

Cevabı ve açıklamayı göster

Cevap: The tablet's physical USB Type-C port is internally wired only for USB 2.0 signals and lacks host controller hardware support for Thunderbolt.

Cevap

The tablet's physical USB Type-C port is internally wired only for USB 2.0 signals and lacks host controller hardware support for Thunderbolt.

The USB Type-C connector is a universal physical form factor. However, the presence of a USB Type-C port does not mean the host device includes a Thunderbolt controller or high-speed data lines. If the tablet's chipset only implements a USB 2.0 host controller, high-speed Thunderbolt peripherals will fall back to USB 2.0 speeds (

480\text{ Mbps}

Adım Adım Çözüm

Analyze physical connector vs protocol capabilities.

Identify that USB Type-C is a physical form factor, whereas USB 2.0, USB 3.2, DisplayPort Alt Mode, and Thunderbolt 3/4 are underlying protocol standards.

Having a USB Type-C port on a mobile device does not automatically imply high-speed Thunderbolt controller support.

Evaluate the observed throughput symptom.

Data transfers are limited to

480\text{ Mbps}

, which is the theoretical maximum bandwidth for USB 2.0.

When a high-speed peripheral is connected to a port that only supports USB 2.0 host signals, the connection falls back to the lowest common protocol speed supported by the host port.

Anahtar Kavram

USB Type-C Connector vs Protocol Capabilities

ÖncekiSayfa 172 / 178Sonraki

Tüm alıştırma soruları

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram