Examkin

Tüm alıştırma soruları

396 soru

Tüm türler5,215Çoktan seçmeli2,665Çoklu seçim6Doğru / Yanlış260Sayısal512Eşleştirme930Sıralama396Boşluk doldurma397Kısa cevap49
Soru 1Soru →

A base quartermaster is reviewing supply orders for the mess hall. Arrange the following provisions by their calculated unit price per pound, from least expensive to most expensive.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct order from least expensive to most expensive unit price is: 10 pounds of rice, 4 pounds of salt, 5 pounds of flour, and 2 pounds of pepper.
To find the correct order, calculate the unit price for each item. Rice is 0.85perpound,saltis0.85 per pound, salt is 3.10 per pound, flour is 3.70perpound,andpepperis3.70 per pound, and pepper is 7.50 per pound. Arranging these unit prices from lowest to highest gives the sequence: rice, salt, flour, pepper.

Adım Adım Çözüm

1
Calculate the unit price of the rice.
8.50÷10=8.50 ÷ 10 = 0.85 per pound
Dividing total cost by quantity gives the price per pound.
2
Calculate the unit price of the salt.
12.40÷4=12.40 ÷ 4 = 3.10 per pound
Dividing total cost by quantity gives the price per pound.
3
Calculate the unit price of the flour.
18.50÷5=18.50 ÷ 5 = 3.70 per pound
Dividing total cost by quantity gives the price per pound.
4
Calculate the unit price of the pepper.
15.00÷2=15.00 ÷ 2 = 7.50 per pound
Dividing total cost by quantity gives the price per pound.
5
Compare all calculated unit prices and order them from least to greatest.
0.85<0.85 < 3.10 < 3.70<3.70 < 7.50
The question asks for the items to be arranged from least expensive to most expensive.

Anahtar Kavram

Calculating unit rates by dividing a decimal total by a whole number quantity.
Soru 2Soru →

An electrician is preparing to connect a solid copper conductor to a standard screw terminal. Arrange the following steps in the correct operational sequence using the proper electrical hand tools.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

1. Strip the conductor using a wire stripper. 2. Form a loop in the bare copper with needle-nose pliers. 3. Hook the wire clockwise around the screw post. 4. Tighten the terminal screw with a screwdriver.
The correct operational sequence begins by using wire strippers with the proper gauge notch to cleanly remove insulation without nicking the conductor. Needle-nose pliers are then used to bend the bare copper into a hook. The hook is placed clockwise around the screw post so that tightening rotation draws the wire inward. Finally, an appropriately sized screwdriver fastens the terminal screw securely.

Adım Adım Çözüm

1
Use the correctly sized gauge notch of a wire stripper to strip insulation from the conductor end.
Exposes undamaged, bare solid copper wire.
Proper notch selection prevents nicking, which can weaken the solid wire.
2
Grip the bare conductor end with needle-nose pliers and form a 3/4-circle loop.
Produces a clean hook sized to fit the terminal screw diameter.
Needle-nose pliers allow precise shaping without distorting or scarring the copper.
3
Position the hook around the terminal screw post facing clockwise.
The loop opening aligns with the clockwise tightening rotation of the screw.
Clockwise placement ensures rotational friction from the screw draws the wire tighter around the shank.
4
Drive the screw down firmly using a matching insulated screwdriver.
Creates a secure, low-resistance electrical connection.
Proper screwdriver sizing ensures adequate torque without camming out or damaging the screw head.

Anahtar Kavram

Standard hand-tool procedure for terminating solid conductors under screw terminals, including tool selection and clockwise loop orientation.
Tahmini Süre:1m 0s
Soru 3Soru →

Arrange the steps in the correct sequence to illustrate how fuel vapors move through an automotive Evaporative Emission Control (EVAP) system from initial generation to combustion.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence begins with gasoline evaporating in the fuel tank, followed by vapor storage in the charcoal canister, opening of the purge valve by the engine computer, and finally intake manifold vacuum drawing the vapors into the engine cylinders for combustion.
The Evaporative Emission Control (EVAP) system is designed to prevent unburned hydrocarbon vapors from escaping into the environment. The sequence begins when liquid gasoline warms up and evaporates inside the fuel tank. These vapors are routed through dedicated vent lines into a charcoal canister containing activated carbon that absorbs and stores them. When the engine reaches proper operating conditions, the powertrain control module opens the purge valve, allowing engine intake vacuum to draw the stored vapors out of the canister and into the combustion chambers where they are cleanly burned.

Adım Adım Çözüm

1
Identify the origin point of the emissions.
Gasoline evaporates inside the sealed fuel tank.
The process begins when liquid fuel heats up and creates hydrocarbon vapors.
2
Determine where the vapors are routed and held while the engine is off or idling.
Vapors travel to and are absorbed by the charcoal canister.
The canister holds the vapors until the engine is ready to burn them.
3
Identify the control mechanism that initiates purging.
The engine control computer commands the purge valve to open.
The purge valve acts as the gate that regulates when stored vapors can enter the intake system.
4
Determine the final pathway and disposal of the vapors.
Engine vacuum pulls the vapors into the cylinders for combustion.
Burning the fuel vapors inside the engine cylinders safely disposes of the hydrocarbons without atmospheric pollution.

Anahtar Kavram

Evaporative Emission Control (EVAP) system operation and fuel vapor pathway
Tahmini Süre:45s
Soru 4Soru →

In an electronic ignition system, several sequential events must take place to ignite the compressed air-fuel mixture in a cylinder. Arrange the following operational steps in chronological order, from initial engine position detection to cylinder combustion. What is the correct sequence of these events?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct chronological sequence begins with the crankshaft position sensor transmitting a timing signal, followed by the engine control module interrupting the primary circuit, which causes the coil magnetic field to collapse and induce high secondary voltage, and finishes with the high-voltage pulse jumping the spark plug gap.
The correct sequence follows the fundamental flow of modern electronic ignition: sensing engine position (crankshaft sensor), command switching (module cuts primary current), voltage step-up (collapsing magnetic field induces secondary high voltage), and spark discharge (arc jumps the spark plug electrode gap).

Adım Adım Çözüm

1
Identify the initiating trigger event in the electronic ignition system.
The crankshaft position sensor monitors engine rotation and provides the timing baseline signal to the control unit.
Electronic systems cannot determine when to fire without initial position input from the engine rotation sensor.
2
Determine the control response to the trigger signal.
The engine control module opens the primary ignition circuit, interrupting low-voltage battery current.
Breaking the primary circuit is the mechanical or solid-state action required to collapse the coil's magnetic field.
3
Trace the magnetic induction response inside the ignition coil.
The collapsing magnetic field cuts through thousands of fine secondary winding turns, stepping up the potential into tens of thousands of volts.
Mutual induction converts low-voltage primary switching into the high-voltage spike needed for ignition.
4
Identify the delivery and combustion stage.
The high-voltage surge reaches the spark plug and arcs across the gap, igniting the compressed charge.
The electrical arc at the spark plug electrodes is the final operational objective of the ignition circuit.

Anahtar Kavram

Electronic Ignition Triggering and High-Voltage Induction Sequence
Tahmini Süre:45s
Soru 5Soru →

An electronics student is preparing to measure an unknown DC voltage across a circuit load using a digital multimeter. Arrange the following steps in the correct sequence to perform this measurement safely and accurately from first to last.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

1. Insert the black test lead into the COM jack and the red test lead into the V/Ω jack. 2. Rotate the selector switch to the highest available DC voltage (DCV) range. 3. Touch the probe tips in parallel across the load while the circuit is energized. 4. Step down the selector switch to a lower range to obtain the most accurate reading.
To measure DC voltage safely, the technician must first install the leads into the COM and V/Ω terminals, set the selector switch to the highest DCV range to prevent overload damage, place the probe tips across the load in parallel, and finally reduce the range selector to achieve maximum measurement resolution.

Adım Adım Çözüm

1
Plug the black test lead into the COM terminal and the red lead into the V/Ω terminal.
The meter is configured for high input impedance.
Connecting to the high-impedance voltage terminals prevents short circuits and protects internal circuitry.
2
Set the rotary function switch to direct current voltage (DCV) at the highest scale.
The meter is protected against potential over-voltage conditions.
When the circuit potential is unknown, starting on the highest range prevents meter overload.
3
Place the probe tips in parallel across the component under test while the circuit operates.
The display registers the potential difference across the load.
A voltmeter must always be connected in parallel with the component being measured.
4
Lower the selector dial range until the measurement fills the display scale.
The reading achieves maximum resolution and accuracy.
Stepping down to the closest range above the measured value yields the greatest number of significant digits.

Anahtar Kavram

Digital multimeter setup, probe placement, and range selection for DC voltage measurements.
Tahmini Süre:1m 0s
Soru 6Soru →

Four identical airtight containers, each with a total volume of 1 m31 \text{ m}^3, are placed in different situations. Arrange these situations in order from the GREATEST buoyant force acting on the container to the LEAST buoyant force.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct order from greatest to least buoyant force is: fully submerged in saltwater, fully submerged in freshwater, half-submerged in freshwater, and sitting on dry land.
Buoyant force is determined by the weight of the displaced fluid. A fully submerged object in saltwater displaces the heaviest amount of fluid. A fully submerged object in freshwater displaces slightly less weight because freshwater is less dense. A half-submerged object displaces only half the volume of water, yielding an even smaller force. An object on dry land displaces no water, experiencing zero buoyant force.

Adım Adım Çözüm

1
Recall Archimedes' Principle.
The buoyant force is equal to the weight of the displaced fluid (Fb=fluid density×volume displaced×gravityF_b = \text{fluid density} \times \text{volume displaced} \times \text{gravity}).
This formula identifies the two main variables that affect buoyant force: the density of the fluid and the volume of fluid displaced.
2
Compare the volume of fluid displaced in each scenario.
Both completely submerged scenarios displace the full 1 m31 \text{ m}^3 volume. The half-submerged floating scenario displaces 0.5 m30.5 \text{ m}^3. The dry land scenario displaces 0 m30 \text{ m}^3.
Volume displaced is the primary factor in determining the magnitude of buoyant force.
3
Compare the fluid densities for the fully submerged scenarios.
Saltwater has a higher density than standard freshwater. Therefore, 1 m31 \text{ m}^3 of saltwater weighs more than 1 m31 \text{ m}^3 of freshwater.
When displaced volumes are equal, the fluid with the higher density exerts a greater buoyant force.
4
Order the scenarios based on the weight of the displaced fluid.
Submerged in Saltwater > Submerged in Freshwater > Half-submerged in Freshwater > Dry land.
This sequence correctly ranks the situations from greatest to least buoyant force.

Anahtar Kavram

According to Archimedes' Principle, buoyant force is directly proportional to both the volume of fluid displaced and the density of that fluid.
Soru 7Soru →

Arrange the following steps in the correct chronological sequence for shrink-fitting a metal collar onto a steel shaft.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

First heat the collar, then slide it over the shaft, allow the assembly to cool, and finally the collar contracts to create a tight grip.
In a shrink-fitting process, the outer component (the collar) must be heated first so that thermal expansion increases its internal diameter. While it is expanded, it is slid over the inner component (the shaft). As the assembly cools to room temperature, the outer component undergoes thermal contraction, shrinking tightly around the shaft to create a secure mechanical grip.

Adım Adım Çözüm

1
Identify the first step required to make the parts fit together.
Heat the metal collar to increase its internal diameter.
Heating causes thermal expansion, creating the necessary clearance for the shaft.
2
Identify the physical assembly step.
Slide the heated collar over the shaft.
The parts must be assembled quickly while the collar is still expanded.
3
Identify the next phase of the physical process.
Allow the assembled collar and shaft to cool.
Removing the heat source allows the metal to return to its original temperature.
4
Identify the final mechanical outcome.
The collar contracts and grips the shaft tightly.
Thermal contraction shrinks the collar's diameter, creating a strong interference fit.

Anahtar Kavram

Thermal Expansion and Contraction
Soru 8Soru →

Arrange the following materials in order from the BEST thermal insulator (slowest rate of heat transfer) to the WORST thermal insulator (fastest rate of heat transfer).

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct order from best to worst thermal insulator is: Fiberglass insulation, Solid wood, Window glass, Copper piping.
Fiberglass traps air, giving it the highest insulation value. Wood is naturally porous and insulates moderately well. Glass is a poor insulator but still restricts heat more than metals. Copper is highly conductive, making it the worst insulator.

Adım Adım Çözüm

1
Identify the material known for intentionally blocking heat transfer.
Fiberglass insulation is designed specifically to prevent heat loss or gain in buildings, placing it first.
Trapped air within the fiberglass matrix provides exceptional resistance to thermal conduction.
2
Evaluate the remaining non-metal materials.
Solid wood is placed second, and window glass is placed third.
Wood's internal cellular structure acts as a moderate insulator (often used for pot handles), whereas solid glass is dense and transfers heat more readily.
3
Identify the material known for thermal conductivity.
Copper piping is placed last.
Metals like copper have highly mobile electrons that transfer kinetic energy (heat) rapidly, making them excellent conductors and terrible insulators.

Anahtar Kavram

Thermal conductivity dictates how quickly heat moves through a material. Good insulators (like air-trapping fiberglass) have low conductivity, while conductors (like metals) have high conductivity.
Soru 9Soru →

An armory quartermaster is ordering gun solvent for weapons maintenance. The solvent is available in four different packaging options. Arrange the options from the lowest price per gallon to the highest price per gallon.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct order from lowest to highest price per gallon is: 2-quart bottle, 5-gallon bucket, 4-gallon case, 1-pint bottle.
By converting all package volumes into gallons, we can compare their unit prices accurately. The 22-quart bottle costs $12.00\$12.00 per gallon, the 55-gallon bucket costs $13.00\$13.00 per gallon, the 44-gallon case costs $13.50\$13.50 per gallon, and the 11-pint bottle costs $14.00\$14.00 per gallon. Arranging them from lowest to highest yields this sequence.

Adım Adım Çözüm

1
Calculate the unit price for the 22-quart bottle.
$12.00\$12.00 per gallon
There are 44 quarts in a gallon, making 22 quarts equivalent to 0.50.5 gallons. $6.00÷0.5=$12.00\$6.00 \div 0.5 = \$12.00 per gallon.
2
Calculate the unit price for the 55-gallon bucket.
$13.00\$13.00 per gallon
Dividing the total cost by the number of gallons: $65.00÷5=$13.00\$65.00 \div 5 = \$13.00 per gallon.
3
Calculate the unit price for the 44-gallon case.
$13.50\$13.50 per gallon
Dividing the total cost by the number of gallons: $54.00÷4=$13.50\$54.00 \div 4 = \$13.50 per gallon.
4
Calculate the unit price for the 11-pint bottle.
$14.00\$14.00 per gallon
There are 88 pints in a gallon. Multiplying the pint price by 88 gives the gallon price: $1.75×8=$14.00\$1.75 \times 8 = \$14.00 per gallon.
5
Order the unit prices from lowest to highest.
$12.00\$12.00, $13.00\$13.00, $13.50\$13.50, $14.00\$14.00
The question asks for the options to be arranged in ascending order based on their price per gallon.

Anahtar Kavram

Converting various liquid volume measurements to a common unit (gallons) in order to accurately compare unit prices.
Soru 10Soru →

A horizontal sliding base is open on the right side. The floor of this base has a small square depression located at the far left end. Three flat shapes must be slid horizontally into the base from the right side to completely fill the empty space.

Shape M: A small square that perfectly fits into the left-side depression.
Shape N: A flat rectangular plate that rests on the floor of the base, covering the left half (including the depression).
Shape P: A large rectangular block that seals the right half of the base.

Arrange the shapes in the correct chronological order they must be inserted from the right side to ensure all pieces can reach their intended final positions without blocking each other.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct order of assembly is: Shape M, then Shape N, then Shape P.
Shape M must enter first because it goes the furthest in (into the depression). Shape N follows to sit above the depression, and Shape P goes last to seal the entrance. Any other order results in physical collisions.

Adım Adım Çözüm

1
Identify the piece that must be placed deepest into the base.
Shape M is the only piece that fits in the left-side depression.
If other pieces are placed first, they will block the path to the depression.
2
Determine the next piece that must slide in without being blocked.
Shape N must go next to cover the floor and sit on top of the depression.
Shape P seals the right half, so it would block Shape N if inserted second.
3
Place the final piece to complete the assembly.
Shape P is inserted last.
It perfectly seals the right opening of the base, finishing the structure.

Anahtar Kavram

Translation-based assembly sequence and collision avoidance
Tahmini Süre:45s
Soru 11Soru →

A carpenter needs to cut a solid timber board to length using a traditional hand crosscut saw. What is the correct chronological sequence of steps to execute a clean, accurate cut without splintering the wood?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence begins with measuring and marking the cut line with a square, scoring a starter kerf on the waste side with backward strokes, cutting at a 45∘45^\circ angle with uniform push strokes, and concluding by supporting the waste cutoff piece while finishing with light strokes.
The correct woodworking sequence begins with layout and marking to define the cut line. Drawing the saw backward creates a starter kerf on the waste side, ensuring the blade stays on track. The main cut is then executed at the standard 45∘45^\circ angle with smooth, full strokes. Finally, supporting the waste piece and easing pressure prevents tear-out and splintering as the cut completes.

Adım Adım Çözüm

1
Lay out the cut line with a square across the face and down the edge of the board.
A clear, square reference line is marked for blade alignment.
Accurate layout must be completed prior to any cutting operation to guarantee dimensions and squareness.
2
Place the saw teeth on the waste side of the pencil line and pull backward several times guided by the thumb.
A starter groove (kerf) is cut into the top edge of the board.
Hand crosscut saws cut primarily on the push stroke; drawing backward first establishes a channel so the blade does not wander or skate across the stock.
3
Lower the saw to a 45∘45^\circ angle relative to the wood face and saw using the full length of the blade.
The alternate-beveled knife-like teeth sever the wood grain fibers cleanly.
A 45∘45^\circ angle provides optimal tooth engagement across the grain for hand crosscutting.
4
Hold the unsupported waste end of the board with the free hand while easing cutting pressure.
The final cut separates cleanly without splitting or chipping.
Without support, the falling weight of the waste piece tears the remaining bottom fibers just before the cut completes.

Anahtar Kavram

Hand Crosscut Sawing Technique and Procedural Sequence
Tahmini Süre:1m 15s
Soru 12Soru →

A technician needs to make an enclosed interior cutout in a sheet of plywood using a hand coping saw without cutting in from the outer edge. What is the correct chronological sequence of steps to perform this operation?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

Mark the layout boundary, drill an access starter hole in the waste area, unhook one end of the blade from the frame, thread the free blade through the hole, and reattach and tension the blade with teeth pointing toward the handle.
Performing an internal piercing cut with a coping saw requires layout first, followed by boring an internal relief hole in the waste material. Next, disconnecting one blade end allows the blade to be threaded through the hole before being re-anchored, oriented teeth-backward toward the handle for pull-stroke cutting, and properly tensioned.

Adım Adım Çözüm

1
Lay out and scribe the internal cut line on the face of the panel.
Defines the exact cut boundary and identifies the internal waste wood.
Accurate layout must precede cutting to avoid damaging the final workpiece dimension.
2
Bore a relief or entry hole within the interior waste zone.
Creates an opening large enough to accept the coping saw blade without crossing the layout line.
The saw frame cannot penetrate solid wood from the outer perimeter without ruining the surrounding material.
3
Loosen the handle or frame tension and unhook one blade pin from its holding spigot.
Frees one end of the blade while keeping the other end mounted or easily manageable.
Allows the blade to be inserted into the closed hole in the material.
4
Pass the disconnected blade end through the drilled starter hole.
The workpiece is now captured within the throat of the coping saw frame.
Positions the blade directly inside the enclosed cutout area.
5
Re-engage the blade pin into the frame spigot, orient the teeth toward the handle, and turn the handle to tension the blade.
The coping saw is fully assembled through the workpiece and ready to cut on the pull stroke.
Proper blade orientation and tension prevent blade deflection and buckling during fine interior curves.

Anahtar Kavram

Coping saw internal piercing procedure and pull-stroke blade orientation
Tahmini Süre:1m 0s
Soru 13Soru →

A shop technician is organizing carbon steel hex-head fasteners by their load-bearing capacity before restocking service bins. Arrange the following SAE bolt head markings in order from lowest minimum tensile strength to highest minimum tensile strength.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

Plain/unmarked head (Grade 2), followed by 3 radial lines (Grade 5), then 5 radial lines (Grade 7), and finally 6 radial lines (Grade 8).
SAE bolt strength is identified by counting the radial lines on the hex head and adding 2. An unmarked bolt head is SAE Grade 2 (~74,000 psi), 3 radial lines designate SAE Grade 5 (~120,000 psi), 5 radial lines designate SAE Grade 7 (~133,000 psi), and 6 radial lines designate SAE Grade 8 (~150,000 psi). Arranging them from lowest to highest tensile capacity yields: unmarked bolt, 3 radial lines, 5 radial lines, and 6 radial lines.

Adım Adım Çözüm

1
Identify the standard rule for determining SAE bolt grades from head markings.
The SAE grade equals the number of radial hash marks plus 2 (Grade = Lines + 2). An unmarked head represents SAE Grade 2.
SAE standard J429 defines fastener tensile strength categories by the count of radial lines embossed on the bolt head.
2
Calculate the SAE grade and corresponding minimum tensile strength for each fastener marking.
Unmarked = Grade 2 (74000 psi74{}000\text{ psi}); 3 lines = Grade 5 (120000 psi120{}000\text{ psi}); 5 lines = Grade 7 (133000 psi133{}000\text{ psi}); 6 lines = Grade 8 (150000 psi150{}000\text{ psi}).
Fastener strength increases sequentially with higher grade numbers.
3
Arrange the fasteners in ascending order from lowest tensile strength to highest tensile strength.
Item with no radial lines → Item with 3 radial lines → Item with 5 radial lines → Item with 6 radial lines.
This orders the bolts from lowest load capacity (74000 psi74{}000\text{ psi}) to highest load capacity (150000 psi150{}000\text{ psi}).

Anahtar Kavram

SAE Bolt Grade Identification and Tensile Strength Hierarchy
Tahmini Süre:1m 0s
Soru 14Soru →

The speed at which light travels depends directly on the optical density and refractive index of the medium through which it passes. Arrange the following media in order of the speed of light within them, from slowest to fastest.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

Diamond, Crown glass, Liquid water, Vacuum (from slowest to fastest)
Light travels fastest through empty space (c≈3.00×108 m/sc \approx 3.00 \times 10^8\text{ m/s}) where the refractive index is 1.001.00. When entering denser transparent media, the wave interacts with the electromagnetic fields of atoms, causing an apparent slowdown proportional to the medium's index of refraction (v=cnv = \frac{c}{n}). Diamond has the highest index of refraction among the options (n≈2.42n \approx 2.42), making it the slowest, followed by crown glass (n≈1.52n \approx 1.52), liquid water (n≈1.33n \approx 1.33), and vacuum (n=1.00n = 1.00).

Adım Adım Çözüm

1
Identify the relationship between the index of refraction and the speed of light.
The speed of light in a medium is inversely proportional to its refractive index, given by v=cnv = \frac{c}{n}, where cc is the speed of light in a vacuum and nn is the refractive index.
Higher refractive indices indicate greater optical density and slower wave propagation speeds.
2
Rank the media by their refractive indices from highest to lowest.
Diamond (n≈2.42n \approx 2.42) > Crown glass (n≈1.52n \approx 1.52) > Liquid water (n≈1.33n \approx 1.33) > Vacuum (n=1.00n = 1.00).
Ranking from highest index to lowest index establishes the reverse order of speed.
3
Invert the refractive index ranking to order the media from slowest speed to fastest speed.
Diamond (slowest, ≈1.24×108 m/s\approx 1.24 \times 10^8\text{ m/s}) →\rightarrow Crown glass (≈1.97×108 m/s\approx 1.97 \times 10^8\text{ m/s}) →\rightarrow Liquid water (≈2.25×108 m/s\approx 2.25 \times 10^8\text{ m/s}) →\rightarrow Vacuum (fastest, ≈3.00×108 m/s\approx 3.00 \times 10^8\text{ m/s}).
Matches the required sequence criteria from slowest to fastest.

Anahtar Kavram

Inverse relationship between index of refraction and wave speed in optical media (v=cnv = \frac{c}{n})
Tahmini Süre:1m 0s
Soru 15Soru →

A quartermaster is reviewing the completion status of four different supply warehouse inventories. To prioritize manpower, arrange the warehouses from the least completed inventory to the most completed inventory.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

Warehouse Charlie, Warehouse Delta, Warehouse Alpha, Warehouse Bravo
By converting all values to percentages (35%35\%, 40%40\%, 25%25\%, and 30%30\%), we can easily compare them. The lowest value is 25%25\% (Charlie), followed by 30%30\% (Delta), then 35%35\% (Alpha), and the highest is 40%40\% (Bravo).

Adım Adım Çözüm

1
Convert all completion statuses to a common format, such as percentages, for direct comparison.
Warehouse Alpha = 35%35\%, Warehouse Bravo = 40%40\%.
Comparing numbers in different formats is difficult and prone to error.
2
Convert the fractions for Warehouse Charlie and Warehouse Delta to percentages.
Warehouse Charlie: 14=25%\frac{1}{4} = 25\%. Warehouse Delta: 310=30%\frac{3}{10} = 30\%.
Fractions with denominators of 44 and 1010 can be easily converted to percentages.
3
Order the converted percentage values from least to greatest.
25%<30%<35%<40%25\% < 30\% < 35\% < 40\%.
The question asks for the order from least completed to most completed.
4
Match the ordered percentages back to their respective warehouses.
Charlie (25%25\%), Delta (30%30\%), Alpha (35%35\%), Bravo (40%40\%).
This provides the final required sequence.

Anahtar Kavram

Converting fractions and decimals to percentages to compare their values.
Tahmini Süre:45s
Soru 16Soru →

A quartermaster is evaluating different vendors to purchase AA batteries. Calculate the price per battery for each option and arrange the vendors in order from the lowest unit price to the highest unit price.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

Vendor Delta, Vendor Bravo, Vendor Alpha, Vendor Charlie
The correct sequence is found by evaluating the cost per single battery for each vendor. By dividing the total cost by the quantity provided, we find that Vendor Delta offers the lowest rate at $0.70\$0.70 per battery. Vendor Bravo follows at $0.80\$0.80 per battery, Vendor Alpha at $0.90\$0.90 per battery, and Vendor Charlie is the most expensive at $1.25\$1.25 per battery. Arranging these calculated unit prices from smallest to largest provides the correct order.

Adım Adım Çözüm

1
Calculate the unit price for Vendor Alpha.
$9.00÷10=$0.90\$9.00 \div 10 = \$0.90 per battery.
To find the cost of a single battery, divide the total cost by the quantity.
2
Calculate the unit price for Vendor Bravo.
$9.60÷12=$0.80\$9.60 \div 12 = \$0.80 per battery.
To find the cost of a single battery, divide the total cost by the quantity.
3
Calculate the unit price for Vendor Charlie.
$2.50÷2=$1.25\$2.50 \div 2 = \$1.25 per battery.
To find the cost of a single battery, divide the total cost by the quantity.
4
Calculate the unit price for Vendor Delta.
$21.00÷30=$0.70\$21.00 \div 30 = \$0.70 per battery.
To find the cost of a single battery, divide the total cost by the quantity.
5
Order the calculated unit prices from lowest to highest.
$0.70\$0.70 (Delta) < $0.80\$0.80 (Bravo) < $0.90\$0.90 (Alpha) < $1.25\$1.25 (Charlie)
This establishes the correct sequence from the most cost-effective to the least cost-effective option.

Anahtar Kavram

Unit price is calculated by dividing the total price by the number of units. Comparing these prices reveals the lowest cost per item.
Soru 17Soru →

A base quartermaster is purchasing different types of office supplies for a training facility. Calculate the total cost for each order and arrange them from the least expensive to the most expensive.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct order from least expensive to most expensive is: 55 boxes of classification folders ($89.25\$89.25), 1212 packs of highlighters ($89.40\$89.40), 66 packs of permanent markers ($89.70\$89.70), and 44 magnetic whiteboards ($89.80\$89.80).
The total cost for each order is found by multiplying the quantity by the price per item. The folders cost $89.25\$89.25 (5×$17.855 \times \$17.85). The highlighters cost $89.40\$89.40 (12×$7.4512 \times \$7.45). The markers cost $89.70\$89.70 (6×$14.956 \times \$14.95). The whiteboards cost $89.80\$89.80 (4×$22.454 \times \$22.45). Ordering these decimal values from least to greatest gives the correct sequence.

Adım Adım Çözüm

1
Calculate the total cost for the classification folders.
$89.25\$89.25
Total cost equals quantity multiplied by unit price (5×$17.855 \times \$17.85).
2
Calculate the total cost for the highlighters.
$89.40\$89.40
Total cost equals quantity multiplied by unit price (12×$7.4512 \times \$7.45).
3
Calculate the total cost for the permanent markers.
$89.70\$89.70
Total cost equals quantity multiplied by unit price (6×$14.956 \times \$14.95).
4
Calculate the total cost for the magnetic whiteboards.
$89.80\$89.80
Total cost equals quantity multiplied by unit price (4×$22.454 \times \$22.45).
5
Compare the calculated total costs and arrange them from least to greatest.
$89.25<$89.40<$89.70<$89.80\$89.25 < \$89.40 < \$89.70 < \$89.80
To fulfill the requirement of ordering from least expensive to most expensive.

Anahtar Kavram

Calculating total cost by multiplying unit price by quantity, and comparing decimal values.
Soru 18Soru →

An aviation structural mechanic is processing four requisition forms for aircraft maintenance. Calculate the total cost (materials plus shipping) for each order and arrange them in sequence from least to greatest total cost.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct order from least to greatest total cost is: Order 4 ($65.30\$65.30), Order 2 ($66.00\$66.00), Order 3 ($66.20\$66.20), and Order 1 ($71.50\$71.50).
Evaluating each order gives the following totals: Order 4 is $65.30\$65.30, Order 2 is $66.00\$66.00, Order 3 is $66.20\$66.20, and Order 1 is $71.50\$71.50. Arranging these from least to greatest yields the sequence: Order 4, Order 2, Order 3, Order 1.

Adım Adım Çözüm

1
Calculate the total cost for Order 1.
15×4.20=63.0015 \times 4.20 = 63.00. Adding shipping: 63.00+8.50=71.5063.00 + 8.50 = 71.50. Total is $71.50\$71.50.
To determine the complete cost of the spark plugs including the fee.
2
Calculate the total cost for Order 2.
4×12.75=51.004 \times 12.75 = 51.00. Adding shipping: 51.00+15.00=66.0051.00 + 15.00 = 66.00. Total is $66.00\$66.00.
To determine the complete cost of the air filters including the fee.
3
Calculate the total cost for Order 3.
20×2.85=57.0020 \times 2.85 = 57.00. Adding shipping: 57.00+9.20=66.2057.00 + 9.20 = 66.20. Total is $66.20\$66.20.
To determine the complete cost of the safety wire including the fee.
4
Calculate the total cost for Order 4.
8×7.60=60.808 \times 7.60 = 60.80. Adding shipping: 60.80+4.50=65.3060.80 + 4.50 = 65.30. Total is $65.30\$65.30.
To determine the complete cost of the sealant including the fee.
5
Arrange the calculated totals from least to greatest.
The values in ascending order are $65.30\$65.30 (Order 4), $66.00\$66.00 (Order 2), $66.20\$66.20 (Order 3), and $71.50\$71.50 (Order 1).
To answer the question's requirement of sorting the final values.

Anahtar Kavram

Decimal Operations and Currency Word Problems
Soru 19Soru →

During the power stroke of a four-stroke internal combustion engine, high-pressure combustion gases drive internal components to produce usable rotational work. In what sequence is mechanical force transferred through the engine's internal components from initial gas expansion to the drivetrain output?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence of mechanical force transfer begins with the piston crown, travels through the wrist pin to the connecting rod, translates into rotational torque at the crankshaft rod journal, and delivers rotational energy to the flywheel.
In a four-stroke internal combustion engine, the force transmission path follows a strict physical chain of interconnected parts. Expanding combustion gases push the piston downward. The piston transfers this linear thrust via the wrist pin (piston pin) to the small end of the connecting rod. The connecting rod transfers the force down its beam to the large end, which acts on the offset rod journal of the crankshaft. The crankshaft converts this linear reciprocating motion into rotary motion. Finally, the crankshaft rotates the flywheel, which dampens torsional pulses and transfers rotational power out of the engine.

Adım Adım Çözüm

1
Identify the initial point of force creation in the cylinder.
Combustion occurs in the combustion chamber above the piston, exerting direct downward pressure on the piston crown.
Expanding hot gases act directly on the piston top, making it the first mechanical component in the power transmission chain.
2
Trace the mechanical connection between the piston body and the connecting rod.
The wrist pin (gudgeon pin) receives the load from the piston bosses and transfers it to the connecting rod small end.
The piston cannot connect directly to the rotating crankshaft without an intermediate pivot pin and rod.
3
Trace the transmission of linear thrust along the rod beam to the crank assembly.
The connecting rod carries the thrust downward from the small end to the big end bearing journal.
The connecting rod spans the distance between the piston and the crank throw, swinging laterally as the crank rotates.
4
Determine where linear motion becomes rotary motion.
The crankshaft rod journal converts the downward linear thrust of the connecting rod into rotating torque.
The offset design of the crankshaft journals leverages the rod's downward push to rotate the crankshaft.
5
Identify the final output component that stabilizes and transmits rotational energy.
The flywheel bolted to the end of the crankshaft receives the rotational torque and delivers it toward the drivetrain.
The flywheel acts as the terminal rotational inertia damper and clutch/torque converter mounting surface on the engine assembly.

Anahtar Kavram

Force transmission path and reciprocating-to-rotary motion conversion in internal combustion engines
Tahmini Süre:1m 0s
Soru 20Soru →

An electronics technician needs to remove excess solder from a circuit board contact using a manual spring-loaded desoldering pump (solder sucker). Arrange the procedural steps in the correct sequence from first to last.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence is: prime the plunger into the locked position, melt the solder with the iron tip, place the nozzle directly over the molten pool, and trigger the release button to vacuum the solder.
A manual desoldering pump relies on rapid vacuum suction. The tool must be pre-cocked before thermal application. Once the iron melts the joint, the nozzle is placed adjacent to the iron tip over the liquid pool, and the release button is pressed immediately to extract the molten alloy before it solidifies.

Adım Adım Çözüm

1
Cock the desoldering pump plunger.
The internal spring is compressed and latched, preparing the chamber for rapid suction.
Once solder is melted, time is critical; the tool must be primed before heating the workpiece.
2
Place the soldering iron tip against the joint.
Thermal energy transfers into the old joint, bringing the solder above its melting point.
Solder must be completely liquid to flow freely into the desoldering tool.
3
Bring the pump nozzle to the molten joint.
The nozzle forms a close seal over the molten solder puddle.
Proper nozzle placement ensures maximum suction efficiency without cooling the joint prematurely.
4
Trigger the release button.
The spring releases, pulling a rapid vacuum that draws the liquid solder inside the barrel.
Immediate suction captures the solder while it remains at liquid temperature.

Anahtar Kavram

Operating procedure for vacuum desoldering tools in electronics maintenance.
Tahmini Süre:45s
Sayfa 1 / 20Sonraki