Tüm alıştırma soruları

Soru 2381Soru →

Evaluate the accuracy of the following claim: During a head-on collision between a heavy commercial transport truck and a lightweight passenger car, the impact force that the truck exerts on the car is greater in magnitude than the force that the car exerts on the truck.

Doğru

Yanlış

Cevabı ve açıklamayı göster

Cevap: False

Cevap

The claim is false. The forces exerted by the two vehicles upon each other are identical in magnitude.

The statement is false because Newton's Third Law of Motion dictates that any two interacting bodies exert equal and opposite forces upon one another. Even though the truck possesses a much larger mass, the actual force of impact it applies to the car is exactly the same magnitude as the force the car applies to the truck.

Adım Adım Çözüm

1

Identify the two interacting objects and the physical law governing their interaction.

The objects are the heavy truck and the lightweight car. The mutual interaction is governed by Newton's Third Law of Motion (action and reaction).

Determining the correct physical principle is necessary to evaluate the relationship between the forces during the collision.

2

Apply Newton's Third Law to the collision scenario.

The law states that for every action force, there is an equal and opposite reaction force. Therefore, the force the truck exerts on the car must be identical in magnitude to the force the car exerts on the truck.

This direct application of the law disproves the claim made in the question stem.

3

Differentiate between the applied force and the resulting acceleration to avoid common misconceptions.

While the impact forces are exactly equal, the car experiences a significantly greater acceleration (and consequently more structural damage) because its mass is much smaller (

a = \frac{F}{m}

).

Clarifying why the car suffers more damage confirms that the unequal effects are due to mass differences under Newton's Second Law, not unequal forces.

Anahtar Kavram

Newton's Third Law states that all forces exist in pairs, and whenever two objects interact, they exert forces upon each other that are equal in magnitude and opposite in direction.

Alternatif Yöntem

You can logically verify this by considering Newton's Second Law combined with the Third Law. The perfectly equal forces cause different accelerations inversely proportional to the masses (

a = \frac{F}{m}

). The car's massive acceleration often misleads observers into incorrectly assuming the force applied to it was larger.

Tahmini Süre:45s

Soru 2382Soru →

Match each thermodynamic process or thermal property to its correct physical description regarding phase changes and energy transfer.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Sublimation matches the direct solid-to-gas transition. Latent Heat of Vaporization matches the energy absorbed during a liquid-to-gas phase change at constant temperature. Condensation matches the transition from gas to liquid. Sensible Heating matches a temperature increase within a single phase.

Each thermodynamic term has a specific mechanical definition. Sublimation skips the liquid phase. Latent heat drives phase changes at a constant temperature plateau, whereas sensible heat drives temperature changes without altering the phase. Condensation is the exothermic return from gas to liquid.

Adım Adım Çözüm

1

Analyze the definitions for phase transitions that bypass the liquid state entirely.

Identify that Sublimation matches the transition directly from solid to gas.

Sublimation is a unique phase change property observed in substances like dry ice, skipping the melting phase.

2

Distinguish between latent heat and sensible heat.

Map Latent Heat of Vaporization to the process where state changes but temperature is constant, and map Sensible Heating to the process where temperature increases but state remains unchanged.

Latent heat plateau occurs during phase changes, whereas sensible heat causes a measurable temperature change on a thermometer.

3

Identify the remaining gas-to-liquid phase change.

Condensation matches the process of a gas releasing heat to become a liquid.

This is a standard thermodynamic reversal of boiling/vaporization.

Anahtar Kavram

States of Matter, Phase Transitions, and Thermal Energy Types

Tahmini Süre:1m 0s

Soru 2383Soru →

A worker uses an industrial paper cutter to slice through thick cardboard. The cutter operates as a second-class lever with the pivot (fulcrum) at one end of the blade. The cardboard is positioned $8\text{ inches}$ from the pivot and creates a cutting resistance of $120\text{ lbs}$ . If the worker pushes down on the handle at a distance of $40\text{ inches}$ from the pivot, what is the minimum downward effort force required to cut the cardboard?

24\text{ lbs}

30\text{ lbs}

20\text{ lbs}

600\text{ lbs}

Cevabı ve açıklamayı göster

Cevap: $24\text{ lbs}$

Cevap

The minimum downward effort force required is

24\text{ lbs}

.

In a second-class lever, the effort torque must equal the load torque. By multiplying the cutting resistance (

120\text{ lbs}

) by its distance from the fulcrum (

8\text{ inches}

), we find a load torque of

960\text{ inch-lbs}

. Dividing this torque by the total effort distance from the fulcrum (

40\text{ inches}

) gives a minimum effort force of

24\text{ lbs}

.

Adım Adım Çözüm

1

Identify the lever class and the given variables.

This is a second-class lever. Load (

F_L

) =

120\text{ lbs}

, Load arm (

d_L

) =

8\text{ inches}

, Effort arm (

d_E

) =

40\text{ inches}

.

Correctly identifying the lever class ensures that the distances are properly measured from the fulcrum.

2

Apply the torque balance (principle of moments) equation.

F_E \times d_E = F_L \times d_L

For the lever to balance and cut the cardboard, the input effort torque must equal the output load torque.

3

Substitute the known values and solve for the effort force (

F_E

).

F_E \times 40 = 120 \times 8 \rightarrow 40 F_E = 960 \rightarrow F_E = 24\text{ lbs}

.

Calculating this equation yields the minimum effort force required.

Anahtar Kavram

Torque Balance in Second-Class Levers

Tahmini Süre:1m 0s

Soru 2384Soru →

While inspecting an engine valvetrain, a mechanic measures the outside diameter of a pushrod using a micrometer graduated in thousandths of an inch. The sleeve displays the major digit $3$ and reveals $2$ full minor tick marks past the digit. The thimble bevel aligns precisely on the graduation mark $14$ . What is the pushrod diameter measurement?

0.314\text{ inch}

0.339\text{ inch}

0.364\text{ inch}

0.389\text{ inch}

Cevabı ve açıklamayı göster

Cevap: $0.364\text{ inch}$

Cevap

The measured pushrod diameter is

0.364\text{ inch}

.

The total reading is obtained by combining the major sleeve increment of

0.300\text{ inch}

, the two visible minor subdivision marks (

2 \times 0.025\text{ in.} = 0.050\text{ inch}

), and the thimble graduation of

0.014\text{ inch}

, resulting in

0.300 + 0.050 + 0.014 = 0.364\text{ inch}

.

Adım Adım Çözüm

1

Read the largest visible major number on the sleeve and multiply by

0.100\text{ inch}

.

3 \times 0.100\text{ in.} = 0.300\text{ inch}

Each numbered graduation line along the sleeve represents one-tenth (

0.100

) of an inch.

2

Count the visible minor subdivision marks between the major digit and the thimble edge, multiplying by

0.025\text{ inch}

.

2 \times 0.025\text{ in.} = 0.050\text{ inch}

Each subdivision line represents one complete turn of the thimble, equal to

0.025\text{ inch}

.

3

Read the thimble graduation mark that aligns with the sleeve index line and multiply by

0.001\text{ inch}

.

14 \times 0.001\text{ in.} = 0.014\text{ inch}

The thimble is divided into 25 equal increments of one-thousandth (

0.001

) of an inch each.

4

Calculate the total measurement by adding the three individual scale readings together.

0.300 + 0.050 + 0.014 = 0.364\text{ inch}

The final reading is the sum of the sleeve major reading, sleeve minor increments, and the aligned thimble value.

Anahtar Kavram

Reading a standard inch outside micrometer by summing the major sleeve divisions (

0.100\text{ in.}

), minor sleeve subdivisions (

0.025\text{ in.}

), and thimble graduations (

0.001\text{ in.}

).

Tahmini Süre:45s

Soru 2385Soru →

A motorized boat is accelerating forward across a body of water. According to Newton's Third Law of Motion, which specific force is the reaction force that directly propels the boat forward?

The force of the water pushing forward against the propeller blades

The force of the propeller blades pushing backward against the water

The internal rotational force generated by the boat's engine

The forward momentum of the boat overcoming the water's resting resistance

Cevabı ve açıklamayı göster

Cevap: The force of the water pushing forward against the propeller blades

Cevap

The force of the water pushing forward against the propeller blades directly propels the boat.

According to Newton's Third Law, forces always come in pairs. When the boat's propeller pushes water backward (action), the water simultaneously exerts an equal and opposite force forward on the propeller (reaction). Because the propeller is attached to the boat, this reaction force is what propels the entire vessel forward.

Adım Adım Çözüm

1

Identify the interacting bodies in the mechanical system.

The two primary interacting bodies are the boat's propeller and the surrounding water.

Newton's Third Law requires identifying the two distinct bodies exerting forces on each other.

2

Determine the action force created by the boat's mechanism.

The turning propeller exerts a force backward against the water.

To move forward, a marine propulsion system must push fluid in the opposite direction.

3

Apply Newton's Third Law to find the equal and opposite reaction force.

If the propeller pushes the water backward, the water must push the propeller forward with an equal magnitude of force.

Forces always occur in simultaneous pairs acting on different objects.

4

Isolate the force that acts specifically on the boat.

The forward force from the water acting on the propeller blades is what accelerates the boat forward.

An object's acceleration is determined only by the external forces acting upon it, not the forces it exerts on other things.

Anahtar Kavram

Newton's Third Law requires that for every action force, there is a simultaneous reaction force equal in magnitude and opposite in direction, acting on two different bodies.

Soru 2386Soru →

A red-hot steel component is dropped into a vat of liquid coolant that is exactly at its boiling point. As the steel transfers extreme heat into the coolant, the fluid begins to boil vigorously. Assuming the vat is open to the atmosphere, what happens to the temperature of the remaining liquid coolant while this boiling phase change is actively occurring?

It remains constant because the absorbed thermal energy is used entirely to change the liquid into a gas.

It continues to rise steadily since extreme heat is being continuously transferred into the fluid.

It decreases momentarily because the rapid bubbling action creates strong convective cooling currents.

It increases at a significantly slower rate because the liquid expands, distributing the heat over a larger volume.

Cevabı ve açıklamayı göster

Cevap: It remains constant because the absorbed thermal energy is used entirely to change the liquid into a gas.

Cevap

It remains constant because the absorbed thermal energy is used entirely to change the liquid into a gas.

During a phase change like boiling or melting, the temperature of a substance remains completely flat (forms a plateau) even though heat is continually being added. The thermal energy from the red-hot steel is absorbed by the coolant as 'latent heat of vaporization'. This energy strictly breaks the physical bonds between the liquid molecules to turn them into a gas, so the average kinetic energy (which dictates temperature) of the remaining liquid stays exactly the same.

Adım Adım Çözüm

1

Identify the initial state of the coolant.

The coolant is a liquid already at its boiling point.

This establishes that the fluid is perfectly primed to undergo a phase change from liquid to gas without needing to warm up further.

2

Analyze the energy transfer occurring in the system.

Massive amounts of thermal energy are being transferred from the red-hot steel into the liquid coolant.

This continuous heat transfer drives the vigorous boiling observed in the vat.

3

Apply thermodynamic principles regarding phase changes.

The temperature of the liquid will not change; instead, the added heat is absorbed as latent heat of vaporization.

During a phase change, added energy breaks intermolecular bonds rather than increasing the kinetic energy (temperature) of the liquid molecules.

Anahtar Kavram

Latent Heat and Phase Change Plateaus

Tahmini Süre:1m 0s

Soru 2387Soru →

When comparing Schedule 80 PVC pipe to Schedule 40 PVC pipe of the same nominal diameter, which of the following statements correctly describes the structural and operational difference between them?

Schedule 80 has a larger outside diameter and thinner walls to increase fluid flow capacity.

Schedule 80 has a thicker wall and smaller inside diameter, giving it a higher pressure rating.

Schedule 80 has a thinner wall and flexible cross-linked structure designed for tight-radius bending.

Schedule 80 is manufactured with an internal rubber liner specifically to transport heated potable water.

Cevabı ve açıklamayı göster

Cevap: Schedule 80 has a thicker wall and smaller inside diameter, giving it a higher pressure rating.

Cevap

Schedule 80 PVC pipe has a thicker wall and a smaller inside diameter than Schedule 40 PVC of the same nominal size, providing greater mechanical strength and a higher pressure rating.

Standard pipe manufacturing maintains a uniform outside diameter for any given nominal pipe size so that standard fittings and cutting tools function uniformly. Higher schedule ratings, such as Schedule 80 compared to Schedule 40, specify a thicker pipe wall. Because the outside diameter is constant, the thicker wall extends inward, reducing the inside diameter while significantly increasing the pipe's tensile strength and working pressure rating.

Adım Adım Çözüm

1

Identify the standard sizing convention for rigid pipe schedules.

For any given nominal pipe size, the outside diameter (OD) remains identical across all schedule ratings so standard fittings can be used.

Standardizing outside diameter ensures compatibility across trade fittings and threading equipment.

2

Determine how increasing the schedule rating from 40 to 80 affects pipe wall thickness and performance.

Schedule 80 adds material to the interior of the pipe, producing a thicker wall, a smaller inside diameter (ID), and a substantially higher working pressure tolerance.

Thicker wall cross-sections resist higher hoop stress caused by internal fluid pressure.

Anahtar Kavram

Pipe schedule ratings and wall thickness relationships in plumbing materials

Tahmini Süre:1m 0s

Soru 2388Soru →

A mechanic pours four common automotive fluids into a clear, tall recovery cylinder. Assuming they do not mix and are allowed to settle completely into distinct layers, arrange the fluids in order from the TOP layer to the BOTTOM layer.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct order from the top layer to the bottom layer is: Gasoline, SAE 30 Engine Oil, Fresh Water, and finally Ethylene Glycol (Antifreeze).

When immiscible fluids are mixed and allowed to settle, they separate into distinct layers based on their specific gravity. The fluid with the lowest specific gravity (gasoline, ~0.73) will float on top. Engine oil (~0.88) comes next, floating on the fresh water (1.0). Ethylene glycol antifreeze (~1.11) is the densest fluid of the group and will sink to the very bottom.

Adım Adım Çözüm

1

Identify the physical property that determines how fluids layer.

Fluids layer based on their density or specific gravity. The least dense fluid floats on top, and the most dense fluid sinks to the bottom.

Buoyancy dictates that lighter fluids will displace heavier ones downwards.

2

Recall the relative specific gravities of the listed automotive fluids.

Gasoline is the lightest (SG ~0.73), followed by engine oil (SG ~0.88), fresh water (SG 1.0), and ethylene glycol antifreeze (SG ~1.11).

Understanding the density of common mechanical fluids is necessary for diagnosing leaks and fluid separation.

3

Arrange the fluids according to their specific gravity from lowest (top) to highest (bottom).

Gasoline, Engine Oil, Water, Antifreeze.

This matches the instruction to order from the top layer to the bottom layer.

Anahtar Kavram

Density and Specific Gravity

Soru 2389Soru →

Match each automotive shop lifting and safety device to its primary supporting function or safety role.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Jack stands match with rigid mechanical support for working underneath; Wheel chocks match with blocking ground wheels to prevent rolling; Hydraulic floor jack matches with dynamically raising the vehicle to working height; Engine crane matches with suspending and lifting heavy engine assemblies.

Each shop tool is paired according to OSHA and industry shop safety standards: jack stands provide rated mechanical holding under chassis pinch welds or frame rails; wheel chocks maintain stationary ground contact; hydraulic jacks lift the load; and engine hoists balance and remove top-heavy motor assemblies.

Adım Adım Çözüm

1

Identify the primary function of static vehicle supports versus dynamic lifting tools.

Jack stands are designated for static mechanical holding, whereas a hydraulic floor jack is used solely to raise and lower the load.

Hydraulic jacks rely on fluid pressure and bypass valves that can leak or fail, making mechanical stands mandatory for under-vehicle work.

2

Identify the preventive safety equipment used to immobilize the vehicle.

Wheel chocks wedge against tires remaining on the shop floor.

Chocking prevents the vehicle from pivoting or rolling off lifting equipment.

3

Identify the specialized component removal equipment.

The engine crane (hoist) uses an overhead boom to lift heavy assemblies out from above.

Heavy powertrain units require overhead suspension and controlled clearance during removal.

Anahtar Kavram

Distinction between dynamic lifting devices, static mechanical supports, and vehicle stabilization tools in automotive shop safety.

Tahmini Süre:1m 0s

Soru 2390Soru →

Plumbing systems utilize various piping materials that each require specific fastening and connection techniques to ensure leak-free performance. Which standard joining method corresponds to each plumbing pipe material?

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Cross-linked Polyethylene (PEX) matches with mechanical crimp rings or expansion sleeves; Chlorinated Polyvinyl Chloride (CPVC) matches with specialized solvent cement; Cast Iron (Hubless) matches with elastomeric neoprene gaskets and stainless steel clamp shields; Type L Rigid Copper matches with soldering into capillary fittings using a torch.

Each plumbing pipe material possesses unique chemical and physical properties that dictate its trade joining process: PEX utilizes mechanical expansion or crimp rings over barbed fittings; CPVC requires chemical fusion via specialized solvent cement; hubless cast iron relies on rubber neoprene gaskets enclosed by stainless steel clamp bands; and copper requires capillary soldering (sweating) using flux and a torch.

Adım Adım Çözüm

1

Identify the joining requirements for flexible thermoplastic tubing (PEX)

PEX is joined mechanically with crimp/cinch rings or expansion fittings because its cross-linked structure cannot be solvent welded.

PEX does not melt or dissolve with chemical solvents.

2

Identify the joining requirements for rigid hot/cold plastic pipe (CPVC)

CPVC uses primer and specific CPVC solvent cement to fuse the pipe and fitting chemically.

Solvent welding softens and fuses thermoplastic pipe surfaces together.

3

Identify the joining requirements for heavy drainage pipe (Hubless Cast Iron)

Hubless cast iron uses no-hub mechanical couplings featuring a neoprene gasket and a corrugated stainless steel shield with tightening bands.

Cast iron cannot be threaded or easily welded in the field and requires flexible, vibration-resistant mechanical joints.

4

Identify the joining requirements for metallic supply tubing (Type L Copper)

Type L copper is soldered (sweated) using flux and solder heated by a torch.

Capillary action draws liquid solder into the tight clearance between the copper tube and fitting.

Anahtar Kavram

Plumbing Pipe Material Compatibility and Joint Fastening Methods

Tahmini Süre:1m 15s

Soru 2391Soru →

A warehouse worker uses a first-class lever to lift a machinery part weighing $200\text{ lbs}$ . The fulcrum is placed exactly $2\text{ feet}$ from the machinery part. If the worker applies a downward effort force at a distance of $8\text{ feet}$ from the fulcrum on the opposite side, how much effort force is required to balance the load? (Assume the lever itself is weightless.)

Cevabı ve açıklamayı göster

Cevap: 50

Cevap

50

A first-class lever is balanced when the torque on one side of the fulcrum equals the torque on the other side. Torque is calculated by multiplying the force by its distance from the fulcrum. The machinery part creates a torque of

200\text{ lbs} \times 2\text{ ft} = 400\text{ ft-lbs}

. To balance this, the effort force applied at

8\text{ ft}

must also create

400\text{ ft-lbs}

of torque. Therefore, the required effort force is

\frac{400}{8} = 50\text{ lbs}

.

Adım Adım Çözüm

1

Set up the torque balance equation for a lever in equilibrium.

\text{Load} \times \text{Load Arm} = \text{Effort Force} \times \text{Effort Arm}

For a lever to balance, the rotational forces (torques) on both sides of the fulcrum must be equal.

2

Substitute the given values into the equation.

200 \times 2 = \text{Effort Force} \times 8

The load is

200\text{ lbs}

located

2\text{ ft}

from the fulcrum, and the effort is applied

8\text{ ft}

from the fulcrum.

3

Calculate the unknown effort force.

400 = \text{Effort Force} \times 8 \implies \text{Effort Force} = \frac{400}{8} = 50

Dividing the total load torque by the effort arm distance gives the required effort force.

Anahtar Kavram

The principle of moments (torque balance) dictates that a lever is in equilibrium when the clockwise torque equals the counterclockwise torque.

Soru 2392Soru →

A technician uses a standard steel rule to measure a piece of flat bar stock that is $5\frac{5}{8}\text{ inches}$ long. If a piece measuring $\frac{3}{8}\text{ inch}$ is cut off from one end, what is the remaining length of the stock in inches, expressed as a decimal?

Cevabı ve açıklamayı göster

Cevap: 5.25

Cevap

The remaining length of the stock is

5.25\text{ inches}

.

Subtracting

\frac{3}{8}\text{ inch}

from the original length of

5\frac{5}{8}\text{ inches}

yields

5\frac{2}{8}\text{ inches}

. Simplifying the fraction gives

5\frac{1}{4}\text{ inches}

, which converts to

5.25\text{ inches}

in decimal notation.

Adım Adım Çözüm

1

Subtract the cut length from the initial measured length.

5\frac{5}{8}\text{ in} - \frac{3}{8}\text{ in} = 5\frac{2}{8}\text{ in}

Cutting off material reduces the total length, requiring subtraction of the two values.

2

Simplify the fractional measurement and convert to decimal form.

5\frac{2}{8}\text{ in} = 5\frac{1}{4}\text{ in} = 5.25\text{ in}

Reducing

\frac{2}{8}

to

\frac{1}{4}

allows direct decimal conversion as

0.25

added to the whole number

5

.

Anahtar Kavram

Linear measurement arithmetic and fractional reduction on standard shop rules.

Alternatif Yöntem

Convert the mixed fractions directly to decimals before subtracting:

5\frac{5}{8} = 5.625

and

\frac{3}{8} = 0.375

. Then calculate

5.625 - 0.375 = 5.25\text{ inches}

.

Tahmini Süre:45s

Soru 2393Soru →

During the operation of a pneumatic nailer, its internal firing reservoir holds a compressed air volume of $20 \text{ in}^3$ at an absolute pressure of $120 \text{ psi}$ . When the trigger is pulled, the air expands into the driver chamber at a constant temperature until the absolute pressure drops to $30 \text{ psi}$ . Based on Boyle's Law, what is the new total volume of the expanded air in cubic inches?

Cevabı ve açıklamayı göster

Cevap: 80

Cevap

80

According to Boyle's Law, pressure and volume are inversely proportional at a constant temperature (

P_1 \times V_1 = P_2 \times V_2

). The pressure drops from 120 psi to 30 psi, which is a factor of 4 decrease. Because the relationship is inversely proportional, the volume must increase by a factor of 4. Therefore, the initial volume of 20 cubic inches is multiplied by 4, resulting in a final volume of 80 cubic inches.

Adım Adım Çözüm

1

Identify the initial and final states of the gas.

Initial pressure

P_1 = 120 \text{ psi}

, Initial volume

V_1 = 20 \text{ in}^3

. Final pressure

P_2 = 30 \text{ psi}

.

Establishing the known parameters is required before applying the appropriate gas law.

2

Apply Boyle's Law formula.

P_1 \times V_1 = P_2 \times V_2

Since the temperature is constant, Boyle's Law relates the pressure and volume of the trapped air.

3

Substitute values and solve for the unknown final volume (

V_2

).

120 \times 20 = 30 \times V_2 \rightarrow 2400 = 30 \times V_2 \rightarrow V_2 = 80

Isolating

V_2

provides the final expanded volume of the air.

Anahtar Kavram

Boyle's Law states that the absolute pressure of a confined gas is inversely proportional to its volume, provided the temperature remains constant.

Alternatif Yöntem

Use proportional reasoning: Observe that the final pressure (30 psi) is exactly one-quarter (1/4) of the initial pressure (120 psi). Because pressure and volume are inversely proportional under constant temperature, the final volume must be four times (4x) the initial volume. 4 × 20 = 80.

Tahmini Süre:1m 0s

Soru 2394Soru →

During component inspection and shop service, technicians select specialized precision instruments based on the exact type of clearance or dimension being evaluated. Match each precision measurement instrument to the measurement task it is designed to perform.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Feeler gauge matches measuring narrow gaps; Outside micrometer matches measuring external diameter or thickness; Dial indicator matches detecting minute surface variations and runout; Telescoping gauge matches transferring internal bore dimensions.

Each instrument is paired with its specific shop role: feeler gauges check gap thicknesses, outside micrometers measure external component sizes, dial indicators read surface runout, and telescoping gauges transfer bore dimensions.

Adım Adım Çözüm

1

Identify the primary function of each precision measuring tool based on whether it measures external dimensions, internal dimensions, clearances, or runout deflections.

Feeler gauges measure gap thickness, outside micrometers measure external dimensions directly, dial indicators register surface deflection/runout, and telescoping gauges capture internal dimensions indirectly.

Matching each instrument to its specific physical application ensures correct diagnostic and machining procedures in automotive shop practice.

Anahtar Kavram

Function and Application of Precision Measurement Instruments

Soru 2395Soru →

While servicing an engine cylinder head, a technician measures the outside diameter of an intake valve stem using a standard inch micrometer. The sleeve displays the major number $4$ along with $1$ exposed subdivision mark past it. The thimble aligns exactly at graduation $18$ with the sleeve datum line. What is the measured diameter of the valve stem?

0.418\text{ in}

0.443\text{ in}

0.468\text{ in}

0.432\text{ in}

Cevabı ve açıklamayı göster

Cevap: $0.443\text{ in}$

Cevap

0.443\text{ in}

On a standard inch micrometer, each major digit on the sleeve represents

0.100\text{ in}

, giving

0.400\text{ in}

. The single visible subdivision adds

0.025\text{ in}

, bringing the sleeve subtotal to

0.425\text{ in}

. Adding the aligned thimble reading of

0.018\text{ in}

yields the exact total measurement of

0.443\text{ in}

.

Adım Adım Çözüm

1

Read the main numbered graduations on the micrometer sleeve.

4 \times 0.100\text{ in} = 0.400\text{ in}

Each numbered line along the sleeve represents one-tenth of an inch (

0.100\text{ in}

).

2

Identify the number of visible subdivision marks past the major number on the sleeve.

1 \times 0.025\text{ in} = 0.025\text{ in}

Each subdivision between major numbers represents one full revolution of the spindle, equal to twenty-five thousandths of an inch (

0.025\text{ in}

).

3

Read the graduation on the thimble aligned with the sleeve index line.

18 \times 0.001\text{ in} = 0.018\text{ in}

Each line on the thimble circumference represents one thousandth of an inch (

0.001\text{ in}

).

4

Calculate the total measurement by adding all three scale components together.

0.400\text{ in} + 0.025\text{ in} + 0.018\text{ in} = 0.443\text{ in}

The complete reading on a standard outside micrometer is the arithmetic sum of the sleeve reading and the thimble reading.

Anahtar Kavram

Standard Inch Outside Micrometer Scale Reading

Tahmini Süre:45s

Soru 2396Soru →

A carpenter uses a claw hammer to extract a stubborn nail from a wooden board. The hammer acts as a first-class lever. The distance from the nail to the pivot point (fulcrum) on the hammer's head is $2\text{ inches}$ . The carpenter applies an effort force perpendicular to the handle at a distance of $16\text{ inches}$ from the pivot point. If a resistance force of $280\text{ pounds}$ is required to extract the nail, how many pounds of effort force must the carpenter apply?

Cevabı ve açıklamayı göster

Cevap: 35

Cevap

35 pounds

In a first-class lever, the mechanical advantage is determined by the ratio of the effort arm to the resistance arm. The hammer provides a mechanical advantage of

16 / 2 = 8

. Therefore, the effort force required is the load divided by 8, which is

280 / 8 = 35\text{ pounds}

. Using the fundamental torque balance equation (

F_1 \times d_1 = F_2 \times d_2

),

280 \times 2 = 560

, and

560 / 16 = 35

.

Adım Adım Çözüm

1

State the torque balance equation for a lever.

F_E \times d_E = F_R \times d_R

For the lever to overcome the resistance, the torque applied by the effort must equal the torque exerted by the load.

2

Substitute the given values into the equation.

F_E \times 16 = 280 \times 2

The effort distance (

d_E

) is

16\text{ inches}

, the resistance force (

F_R

) is

280\text{ pounds}

, and the resistance distance (

d_R

) is

2\text{ inches}

.

3

Calculate the total torque of the resistance.

280 \times 2 = 560\text{ inch-pounds}

This represents the total rotational force required to loosen the nail.

4

Solve for the effort force (

F_E

).

F_E = 560 / 16 = 35\text{ pounds}

Dividing the total required torque by the longer effort arm gives the smaller effort force needed.

Anahtar Kavram

Torque Balance and Mechanical Advantage

Soru 2397Soru →

A hydraulic accumulator is a sealed, rigid tank that contains both hydraulic fluid (a liquid) and pressurized nitrogen (a gas). When a pump forces additional hydraulic fluid into the tank and significantly raises the internal pressure, which of the following best describes the volumetric changes of the original contents?

Both the original hydraulic fluid and the nitrogen gas compress by an equal percentage to absorb the increased pressure.

The volume of the nitrogen gas decreases significantly, while the volume of the original hydraulic fluid remains virtually unchanged.

The original hydraulic fluid compresses substantially to make room, while the nitrogen gas volume remains constant.

The nitrogen gas expands to increase the pressure, while the hydraulic fluid decreases in density.

Cevabı ve açıklamayı göster

Cevap: The volume of the nitrogen gas decreases significantly, while the volume of the original hydraulic fluid remains virtually unchanged.

Cevap

The volume of the nitrogen gas decreases significantly, while the volume of the original hydraulic fluid remains virtually unchanged.

Liquids, such as hydraulic fluid, are practically incompressible, meaning their volume does not significantly change when subjected to high pressure. Gases, such as nitrogen, are highly compressible. When the pump forces more liquid into the rigid tank, the internal pressure rises. The gas acts like a spring, compressing into a smaller volume to accommodate the new liquid, while the original liquid retains its volume.

Adım Adım Çözüm

1

Identify the states of matter of the materials inside the accumulator.

The nitrogen is a gas, and the hydraulic fluid is a liquid.

Different states of matter respond differently to applied pressure.

2

Recall the compressibility property of liquids.

Liquids are practically incompressible.

This means adding pressure will not noticeably change the volume of the original hydraulic fluid.

3

Recall the compressibility property of gases.

Gases are highly compressible.

This means the nitrogen gas will be forced into a smaller volume as the pressure inside the rigid tank increases.

4

Combine these principles to determine the outcome.

The added fluid forces the gas to compress into a smaller space, while the original liquid maintains its volume.

This allows the rigid tank to accommodate the additional hydraulic fluid.

Anahtar Kavram

Compressibility of Liquids vs. Gases

Tahmini Süre:1m 0s

Soru 2398Soru →

A plumber is preparing to join cross-linked polyethylene (PEX) water supply tubing using standard brass insert fittings and copper crimp rings. What is the correct sequence of steps to create a secure, leak-free crimped connection?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

Cut the tubing squarely, slide the crimp ring onto the tube, insert the barbed fitting until fully seated, and position the ring over the barbs to compress it with a crimping tool.

The correct procedural order requires cutting the tubing cleanly first, sliding the crimp ring onto the pipe before it expands, seating the barbed fitting fully against its shoulder, and finally positioning and compressing the ring over the barb area.

Adım Adım Çözüm

1

Make a clean, 90-degree square cut on the PEX tubing using a sharp cutter.

The tubing end is smooth, round, and ready to receive fittings without burrs.

An angled or jagged cut prevents full seating against the fitting shoulder, causing uneven sealing and potential leaks.

2

Slide a copper crimp ring over the outside of the tubing and push it past the cut end.

The ring is positioned on the tubing before the outer diameter expands from fitting insertion.

Inserting the barbed fitting first expands the tubing, making it difficult or impossible to slide the crimp ring over the connection area.

3

Push the barbed fitting completely into the tubing until the tube end rests against the shoulder stop.

The tubing fully covers all sealing ridges on the barbed fitting.

Partial insertion leaves sealing barbs exposed, compromising the mechanical grip and water seal.

4

Slide the crimp ring to 1/8" to 1/4" from the tubing end and squeeze the crimping tool jaws completely closed.

The copper ring deforms uniformly around the tubing, locking it permanently into the barbs.

Correct ring placement and full compression ensure even clamping force across the barb ridges.

Anahtar Kavram

PEX Crimp Connection Procedure

Tahmini Süre:1m 0s

Soru 2399Soru →

An automotive technician is preparing to clean greasy transmission components in a solvent degreasing tank. To protect against toxic chemical absorption through the skin and eye injuries from solvent splashes, which personal protective equipment is most appropriate?

Heat-resistant split leather gloves and standard impact safety glasses

Heavy-duty nitrile gloves and chemical splash goggles

Lightweight woven cotton gloves and a tinted oxy-fuel cutting shield

High-voltage insulated rubber gloves and a particulate dust mask

Cevabı ve açıklamayı göster

Cevap: Heavy-duty nitrile gloves and chemical splash goggles

Cevap

Heavy-duty nitrile gloves and chemical splash goggles

Synthetic chemical-resistant gloves made of nitrile or neoprene provide an impermeable physical barrier against petroleum hydrocarbons, while indirect-vent chemical splash goggles form a tight seal to protect the eyes from liquid splashes from all angles.

Adım Adım Çözüm

1

Identify the primary shop hazards associated with the task

The task involves petroleum-based solvents that present chemical splash hazards to the eyes and dermal absorption risks through the skin.

PPE selection must match the specific biological, chemical, or physical hazards present in the work environment.

2

Evaluate glove material compatibility with petroleum degreasers

Synthetic elastomers like nitrile or neoprene resist breakdown and prevent liquid penetration, whereas porous materials (cotton, leather) absorb solvents.

Direct skin contact with hydrocarbon solvents strips protective oils and causes dermatitis or systemic toxicity.

3

Determine the appropriate eye protection for liquid chemical handling

Chemical splash goggles featuring indirect venting seal around the orbit of the eye to stop liquid droplets from entering.

Standard safety glasses with open peripheries only guard against solid impact debris, not liquid chemical splashes.

Anahtar Kavram

Chemical-resistant PPE selection for solvent degreasing and parts washing

Tahmini Süre:1m 0s

Soru 2400Soru →

During an air conditioning service, an automotive technician uses a recovery machine to extract refrigerant. The machine pulls hot, high-pressure refrigerant vapor from the vehicle and continuously removes heat from it until it becomes a subcooled liquid in a storage cylinder. Arrange the following thermodynamic events in the chronological order they occur during this continuous cooling process.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The sequence follows a continuous cooling curve: initial sensible cooling of the vapor, reaching the saturation point, the constant-temperature condensation plateau, the end of the phase change, and finally the sensible cooling of the resulting liquid.

As heat is continuously removed from a superheated vapor, its temperature first drops due to sensible heat loss until it reaches the saturation temperature (condensation point). During the actual phase change from gas to liquid, the temperature remains entirely constant as latent heat is released. Once condensation is 100% complete, the temperature of the newly formed liquid begins to drop again.

Adım Adım Çözüm

1

Identify the initial state and process described in the scenario.

The substance starts as a hot, superheated vapor and is continuously losing thermal energy.

Establishing the starting point is necessary to track the thermal sequence accurately.

2

Determine the first phase of cooling prior to condensation.

The vapor cools down steadily, lowering its molecular kinetic energy until it hits the saturation temperature.

A gas must lose sensible heat and cool to its exact condensation point before it can change state.

3

Analyze the phase change behavior.

The temperature stalls and remains completely constant while the vapor condenses into liquid.

During a phase change, heat removal changes the physical state of the matter (releasing latent heat) without changing the temperature.

4

Determine the final phase of cooling after condensation is complete.

Once the last bit of vapor transforms into liquid, the liquid's temperature begins to drop as sensible heat is removed.

After the phase change plateau ends, further heat removal resumes lowering the temperature of the substance.

Anahtar Kavram

States of Matter and Phase Changes

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Alternatif Yöntem

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Alternatif Yöntem

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Alternatif Yöntem

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar