Tüm alıştırma soruları

Soru 2441Soru →

Prior to performing an under-vehicle inspection on a front-wheel-drive unibody car, a mechanic must select an appropriate contact point for the hydraulic floor jack saddle. Which vehicle component is designed to safely bear the lifting force?

The flat center section of the floor pan under the passenger cabin

The reinforced pinch weld or designated factory jacking point along the rocker panel

The bottom casing of the engine oil pan

The steering tie rod or sway bar link assembly

Cevabı ve açıklamayı göster

Cevap: The reinforced pinch weld or designated factory jacking point along the rocker panel

Cevap

The reinforced pinch weld or designated factory jacking point along the rocker panel is the correct component designed to safely support the vehicle's lifting load.

On unibody passenger vehicles, the structural strength is integrated directly into the body shell rather than a heavy separate frame. Vehicle manufacturers engineer reinforced lift pads and pinch-weld seams along the lower rocker panels to provide rigid, concentrated support points that can bear the vehicle's weight without buckling or damaging surrounding components.

Adım Adım Çözüm

1

Identify the vehicle construction type and locate structural support zones.

Unibody vehicles lack a conventional full-perimeter steel frame and instead use integrated high-strength structural points.

Lifting on unreinforced body panels or mechanical components will cause severe structural damage and vehicle instability.

2

Evaluate the proposed contact surfaces against vehicle engineering specifications.

The factory-specified pinch weld notches along the rocker sill are reinforced with multiple spot-welded steel layers designed specifically for lifting contact.

The floor pan, oil pan, and suspension linkages lack structural load-bearing capacity.

3

Select the only certified load-bearing lift location.

The reinforced pinch weld / factory lift point safely accommodates the floor jack saddle.

Ensures the car remains balanced and structurally intact throughout the lifting process.

Anahtar Kavram

Safe Lift Point Identification on Unibody Vehicles

Tahmini Süre:1m 0s

Soru 2442Soru →

A service technician has completed an underbody repair on a vehicle currently resting securely on mechanical jack stands. In what chronological sequence should the technician perform the following actions to safely lower the vehicle back onto the shop floor?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence begins with raising the vehicle slightly using a hydraulic floor jack to unload the jack stands, followed by removing the jack stands, clearing the work area of tools and personnel, slowly opening the hydraulic release valve to lower the vehicle, and finally removing the wheel chocks once all wheels are on the floor.

Safely lowering a vehicle requires systematically reversing the support process. First, the load must be temporarily taken up by the hydraulic jack to allow the mechanical stands to be freed. Second, the stands must be completely removed so the chassis has a clear path down. Third, the perimeter and underside must be inspected for safety. Fourth, the hydraulic release valve must be slowly metered for a smooth descent. Finally, wheel chocks are removed only after the vehicle is resting solidly on its tires.

Adım Adım Çözüm

1

Engage the hydraulic floor jack at the specified lifting point and pump until the vehicle chassis lifts just off the saddles of the jack stands.

The vehicle load transfers from the stands to the hydraulic jack.

Jack stands cannot be disengaged or pulled out while under full vehicle load.

2

Lower the ratchets or pull the locking pins on the jack stands and slide them clear of the vehicle perimeter.

The underside of the chassis is free of mechanical obstructions.

Removing the stands prevents the vehicle chassis from bottoming out on them during descent.

3

Perform a visual sweep of the undercarriage and surrounding floor area.

Confirmation that no tools, creeper, drain pans, or bystanders are in the drop path.

Ensures personal safety and prevents equipment damage during descent.

4

Slowly twist the jack handle counterclockwise to bleed pressure from the hydraulic cylinder.

The vehicle descends at a smooth, controlled rate until all wheels contact the ground.

Rapid release can destabilize the vehicle or cause suspension damage.

5

Pull the wheel chocks away from the opposite axle tires.

The vehicle is returned to standard resting state on level ground.

Chocks must remain engaged during all elevated operations to prevent accidental rolling.

Anahtar Kavram

Standard Operating Procedure for Safely Lowering Supported Vehicles

Tahmini Süre:1m 15s

Soru 2443Soru →

During vehicle maintenance, technicians utilize specialized equipment and mechanisms to safely raise, hold, and stabilize heavy automotive assemblies. Match each shop lifting or support device with its primary safety function.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Engine support crossbar matches suspending the engine from above strut towers during subframe removal; Wheel chocks match preventing unraised tires from rolling during lifting; Two-post lift mechanical locking pawl matches mechanically engaging column slots to prevent drop from hydraulic loss; Transmission jack with tie-down chain matches supporting and stabilizing an irregular, heavy drivetrain unit during removal.

Each tool performs a critical, non-redundant shop safety role: the engine support crossbar holds top-side weight during underside chassis disassembly; wheel chocks physically chock ground wheels against kinetic roll; lift locking pawls provide fail-safe physical engagement against hydraulic failure; and transmission jacks provide multi-angle alignment and strap retention for awkwardly balanced gearboxes.

Adım Adım Çözüm

1

Identify the distinct operational context and load-bearing purpose of each listed tool or mechanism

Differentiated top-down suspension, ground-level roll prevention, column mechanical interlocks, and under-car drivetrain cradling

Safe load management requires matching the specific load orientation and risk factor to the dedicated mechanical safety device

2

Pair each device to its dedicated functional definition based on shop safety standards

Four unambiguous, non-interchangeable tool-to-function pairings established

Every piece of lifting equipment in an auto shop is engineered with dedicated safety ratings and specialized geometric adapters

Anahtar Kavram

Selection and application of specialized automotive lifting and load-support safety devices

Tahmini Süre:1m 0s

Soru 2444Soru →

Match each mechanical lever configuration to its corresponding functional outcome and mechanical advantage (MA).

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

The configurations map as follows: Effort in middle is a distance multiplier (MA < 1); Load in middle is a force multiplier (MA > 1) same direction; Fulcrum in middle with long effort arm is a force multiplier (MA > 1) reversed direction; Fulcrum exact middle is a directional change only (MA = 1).

Each lever class uniquely dictates whether the force direction is changed, while the placement of the fulcrum relative to the effort and load dictates the mechanical advantage. First-class levers reverse direction, second-class multiply force in the same direction, and third-class multiply distance in the same direction.

Adım Adım Çözüm

1

Identify the class of each lever configuration based on the middle component.

Fulcrum in middle = 1st Class. Load in middle = 2nd Class. Effort in middle = 3rd Class.

The central component dictates the fundamental behavior and force direction of the lever.

2

Determine the force direction for each class.

First-class levers reverse the direction of force. Second and third-class levers maintain the original direction of force.

Only when the fulcrum acts as a pivot between the input and output (1st class) does the motion arc in opposite directions.

3

Evaluate the mechanical advantage (MA) based on the relative lengths of the effort arm and load arm.

Effort arm > Load arm yields MA > 1 (force multiplier). Effort arm < Load arm yields MA < 1 (distance multiplier). Equal arms yield MA = 1.

Mechanical advantage is calculated as the length of the effort arm divided by the length of the load arm.

4

Synthesize the direction and MA rules to match each configuration to its functional outcome.

Matches are made based on combining the lever class rules with the specific arm length constraints given.

This guarantees an accurate mapping of physical setup to mechanical performance.

Anahtar Kavram

Lever Classes and Mechanical Advantage

Soru 2445Soru →

A machinist operates a manual drill press. The feed lever (acting as the wheel) has an effective length of $8 \text{ inches}$ from the center of rotation. It turns a pinion gear (acting as the axle) with a radius of $1.6 \text{ inches}$ . If the machinist applies a tangential pull of $25 \text{ lbs}$ to the end of the feed lever, what downward force is applied by the pinion gear to the drill quill? (Assume $100\%$ efficiency).

Cevabı ve açıklamayı göster

Cevap: 125

Cevap

The downward force applied by the pinion gear is 125 lbs.

In a wheel and axle system where effort is applied to the larger wheel, the mechanism multiplies the input force. The Ideal Mechanical Advantage (IMA) is found by dividing the effort radius (lever length of 8 inches) by the load radius (pinion gear radius of 1.6 inches). With an IMA of 5, the input force of 25 lbs is multiplied by 5 to yield 125 lbs of output force.

Adım Adım Çözüm

1

Identify the given dimensions and force.

Wheel radius (lever) = 8 inches, Axle radius (pinion) = 1.6 inches, Input Force = 25 lbs.

Identifying known variables is the first step in solving a mechanics problem.

2

Calculate the Ideal Mechanical Advantage (IMA).

IMA = Wheel Radius / Axle Radius = 8 / 1.6 = 5.

The IMA determines how much the wheel and axle mechanism multiplies the input force.

3

Calculate the output force.

Output Force = Input Force × IMA = 25 × 5 = 125 lbs.

In a 100% efficient system, the output force is the product of the input force and the mechanical advantage.

Anahtar Kavram

Ideal Mechanical Advantage of a wheel and axle, calculated as the ratio of their radii.

Soru 2446Soru →

A sealed pneumatic cylinder in a robotic assembly arm contains air at an absolute pressure of $20 \text{ psi}$ . The cylinder has an initial internal volume of $60 \text{ cm}^3$ . During a rapid compression stroke at a constant temperature, the piston reduces the volume to $15 \text{ cm}^3$ . What is the new absolute pressure inside the cylinder?

80 \text{ psi}

5 \text{ psi}

15 \text{ psi}

60 \text{ psi}

Cevabı ve açıklamayı göster

Cevap: $80 \text{ psi}$

Cevap

The absolute pressure increases to

80 \text{ psi}

because reducing the volume by a factor of 4 causes the pressure to multiply by 4.

According to Boyle's Law, pressure and volume are inversely proportional when temperature is constant (

P_1V_1 = P_2V_2

). The initial pressure-volume product is

20 \times 60 = 1200

. To maintain this constant with a new volume of

15 \text{ cm}^3

, the new pressure must be

1200 \div 15 = 80 \text{ psi}

. Alternatively, recognizing that the volume is reduced by a factor of 4 (

60 \div 15 = 4

) means the pressure must increase by a factor of 4 (

20 \times 4 = 80 \text{ psi}

).

Adım Adım Çözüm

1

Identify the initial conditions and the relevant gas law.

Initial pressure (

P_1

) is

20 \text{ psi}

and initial volume (

V_1

) is

60 \text{ cm}^3

. Since temperature is constant, use Boyle's Law:

P_1V_1 = P_2V_2

.

Boyle's Law defines the inversely proportional relationship between the pressure and volume of a gas when temperature remains unchanged.

2

Set up the equation with the known values.

20 \text{ psi} \times 60 \text{ cm}^3 = P_2 \times 15 \text{ cm}^3

Substituting the given parameters prepares the equation to isolate the unknown final pressure (

P_2

).

3

Solve for the final pressure (

P_2

).

1200 = P_2 \times 15

, which simplifies to

P_2 = \frac{1200}{15} = 80 \text{ psi}

.

Isolating

P_2

reveals the new absolute pressure after the compression stroke.

Anahtar Kavram

Boyle's Law (Pressure-Volume Inverse Relationship)

Soru 2447Soru →

A construction worker uses a rigid pry bar to lift a concrete slab that weighs $400\text{ lbs}$ . The fulcrum is placed exactly $1\text{ foot}$ away from the point where the pry bar contacts the slab. If the worker applies a downward force exactly $5\text{ feet}$ away from the fulcrum, how many pounds of effort force must be applied to just balance the slab?

Cevabı ve açıklamayı göster

Cevap: 80

Cevap

80 lbs

To balance the lever, the torque on both sides of the fulcrum must be equal. The load torque is generated by the slab:

400\text{ lbs} \times 1\text{ ft} = 400\text{ ft-lbs}

. To create an equal effort torque on the other side at a distance of

5\text{ feet}

, an effort force of

80\text{ lbs}

is required because

80\text{ lbs} \times 5\text{ ft} = 400\text{ ft-lbs}

.

Adım Adım Çözüm

1

Identify the known variables given in the problem statement.

Load Force (

F_L

) =

400\text{ lbs}

, Load Distance (

d_L

) =

1\text{ ft}

, Effort Distance (

d_E

) =

5\text{ ft}

.

These values are required to calculate the unknown effort force using the law of the lever.

2

Apply the law of the lever (torque balance equation).

F_E \times d_E = F_L \times d_L

A lever is in static equilibrium when the input torque exactly equals the output torque.

3

Substitute the known values and solve for the effort force (

F_E

).

F_E \times 5 = 400 \times 1 \rightarrow 5F_E = 400 \rightarrow F_E = 80

Isolating

F_E

provides the exact pounds of force needed to balance the concrete slab.

Anahtar Kavram

Torque Balance and the Law of the Lever

Tahmini Süre:45s

Soru 2448Soru →

When an engine hoist (shop crane) with an adjustable telescoping boom is extended from its shortest position to its longest reach position, what effect does this extension have on the maximum safe lifting capacity of the crane?

The safe lifting capacity decreases because extending the boom increases the leverage arm and tipping moment on the crane frame.

The safe lifting capacity remains identical because the capacity is determined exclusively by the internal hydraulic pressure rating of the ram.

The safe lifting capacity increases because a longer boom arm provides greater mechanical advantage over the load.

The safe lifting capacity increases because extending the boom disperses the downward force over a wider base footprint.

Cevabı ve açıklamayı göster

Cevap: The safe lifting capacity decreases because extending the boom increases the leverage arm and tipping moment on the crane frame.

Cevap

The safe lifting capacity decreases because extending the boom increases the leverage arm and tipping moment on the crane frame.

Engine hoists utilize telescoping boom arms marked with distinct weight ratings at each pin position. Extending the boom increases the horizontal distance between the suspended load and the front pivot wheels. Because torque equals load force multiplied by horizontal distance, the longer lever arm exerts greater bending stress on the boom and increases tipping risk, requiring the crane's safe working load to decrease accordingly.

Adım Adım Çözüm

1

Analyze the mechanical configuration of a telescoping shop crane boom.

Extending the boom moves the load attachment hook farther away horizontally from the vertical mast and front support wheels.

Lifting capacity depends on structural strength and torque principles where torque equals force multiplied by distance.

2

Determine how the increased moment arm affects the safe working load limit.

Greater reach magnifies bending forces on the steel boom and increases the overturning moment toward the front wheels.

To maintain safety margins against tipping and structural failure, manufacturers de-rate the safe working load at each extension setting (such as reducing a 2-ton rating at minimum extension to 1/2-ton at maximum extension).

Anahtar Kavram

Engine crane boom extension and load capacity de-rating principles

Tahmini Süre:1m 0s

Soru 2449Soru →

A $75 \text{ kg}$ mechanic stands on a slick, oil-covered garage floor with negligible friction. The mechanic pushes forward horizontally against a stationary $150 \text{ kg}$ tool cabinet with a constant force of $200 \text{ N}$ . Which of the following statements correctly describes the forces involved in this interaction?

The cabinet exerts a

100 \text{ N}

backward force on the mechanic, reflecting the ratio of their masses.

The mechanic experiences a backward reaction force only if the

200 \text{ N}

push fails to overcome the cabinet's inertia.

The cabinet experiences a

200 \text{ N}

forward force, and the mechanic experiences a

200 \text{ N}

backward force simultaneously.

The

200 \text{ N}

action force and the

200 \text{ N}

reaction force both act on the cabinet, preventing it from accelerating rapidly.

Cevabı ve açıklamayı göster

Cevap: The cabinet experiences a $200 \text{ N}$ forward force, and the mechanic experiences a $200 \text{ N}$ backward force simultaneously.

Cevap

The statement accurately describing the interaction is that the cabinet experiences a

200 \text{ N}

forward force, and the mechanic simultaneously experiences a

200 \text{ N}

backward force.

According to Newton's Third Law, any force exerted by one object on another is accompanied by an equal and opposite force exerted back by the second object on the first. Because the mechanic pushes the cabinet with

200 \text{ N}

forward, the cabinet simultaneously pushes the mechanic with

200 \text{ N}

backward. The differing masses do not alter the force magnitudes, though they result in different accelerations.

Adım Adım Çözüm

1

Identify the interacting bodies in the given scenario.

The two interacting bodies are the mechanic and the tool cabinet.

Newton's Third Law applies to the forces exerted between two interacting objects.

2

Determine the magnitude and direction of the action force.

The mechanic exerts a forward force of

200 \text{ N}

on the tool cabinet.

This is the initial action provided in the problem description.

3

Apply Newton's Third Law to find the reaction force.

The tool cabinet must exert an equal and opposite reaction force of

200 \text{ N}

backward on the mechanic.

Forces always exist in equal and opposite pairs acting on different objects, regardless of their respective masses or whether they accelerate.

Anahtar Kavram

Newton's Third Law of Motion states that when two objects interact, they apply forces to each other of equal magnitude and opposite direction.

Soru 2450Soru →

A mechanical pressure relief valve is installed on a pneumatic air receiver tank to prevent over-pressurization. Arrange the following events in the correct chronological sequence, from the moment the tank begins to over-pressurize until the system stabilizes.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The sequence begins with system pressure exceeding the setpoint. This creates a pneumatic force that overcomes the spring tension, unseating the valve. The compressed air then vents, lowering system pressure until the spring reseats the valve.

The correct operational sequence of a pneumatic relief valve relies on the balance between gas pressure and mechanical spring force. Initially, an over-pressure condition occurs in the tank. Because force equals pressure multiplied by area, this high pressure exerts an upward force on the valve plug. When this pneumatic force exceeds the downward force of the calibrated spring, the plug lifts. This physical unseating creates a pathway, allowing the highly compressed gas to rapidly expand and vent to the lower-pressure atmosphere. As the gas escapes, the internal tank pressure drops until the pneumatic force is weaker than the spring tension, allowing the spring to snap the valve closed again.

Adım Adım Çözüm

1

Identify the initial condition that triggers the safety system.

The air pressure inside the tank rises above the safe setpoint limit.

A pneumatic relief sequence must begin with an over-pressure event.

2

Determine the mechanical interaction between the compressed air and the valve.

The pneumatic force overcomes the mechanical spring tension.

For the valve to operate, fluid force (Pressure × Area) must defeat the physical mechanism keeping it closed.

3

Establish the physical movement resulting from the force imbalance.

The valve plug lifts off its seat to expose the exhaust port.

The net upward pneumatic force pushes the valve open.

4

Identify the behavior of the gas once the pathway is open.

Compressed air escapes into the atmosphere, reducing tank pressure.

Gas naturally expands and flows from areas of high pressure to low pressure.

5

Determine the condition that ends the sequence.

The spring pushes the valve closed as the pneumatic pressure decreases.

When tank pressure drops sufficiently, the pneumatic force is no longer strong enough to resist the spring.

Anahtar Kavram

Pneumatic System Control and Pressure Relief Operations

Soru 2451Soru →

A carpenter uses a claw hammer to pull a stubborn nail out of a wooden board. The hammer's head rests on the surface of the board while the carpenter pulls back on the handle. In this lever system, which component serves as the fulcrum?

The point where the hammer head contacts the wooden board

The hand applying force to the hammer handle

The nail being gripped and pulled by the claw

The point exactly halfway down the length of the handle

Cevabı ve açıklamayı göster

Cevap: The point where the hammer head contacts the wooden board

Cevap

The correct answer is the point where the hammer head contacts the wooden board.

The fulcrum is defined as the fixed pivot point around which a lever moves. When using a claw hammer to pull a nail, the point where the curved head of the hammer rests against the board acts as this stationary pivot point. It allows the lever to multiply the force applied at the handle to overcome the resistance of the nail.

Adım Adım Çözüm

1

Define the role of a fulcrum in any lever system.

A fulcrum is the stationary point or hinge around which a lever pivots or rotates.

Understanding the mechanical definition is required before analyzing the specific tool.

2

Analyze the physical action of the claw hammer pulling the nail.

As the carpenter pulls the handle (effort) to lift the nail (load), the entire hammer rotates around the point where the curved head presses into the wood.

Mapping the definitions of effort, load, and fulcrum to the real-world scenario identifies the correct component.

Anahtar Kavram

Lever Components: Identifying the Fulcrum, Effort, and Load

Tahmini Süre:30s

Soru 2452Soru →

Pair the following everyday tools with their correct mechanical lever classification.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Scissors match to a First-Class Lever, the paper cutter matches to a Second-Class Lever, and the broom matches to a Third-Class Lever.

Lever classes are defined by which component is located in the middle: the Fulcrum (Class 1), the Load (Class 2), or the Effort (Class 3). The mnemonic 'FLE 123' is commonly used to remember this rule.

Adım Adım Çözüm

1

Analyze the mechanical arrangement of the scissors.

The fulcrum is between the effort and the load, making it a Class 1 lever.

To classify the lever based on its central component.

2

Analyze the mechanical arrangement of the paper cutter.

The load is positioned between the fulcrum and the effort, making it a Class 2 lever.

To classify the lever based on its central component.

3

Analyze the mechanical arrangement of the broom.

The effort is applied between the fulcrum and the load, making it a Class 3 lever.

To classify the lever based on its central component.

Anahtar Kavram

Lever Classification by Central Component

Tahmini Süre:45s

Soru 2453Soru →

A mechanic uses a standard 0 to 1-inch outside micrometer to measure the diameter of a piston wrist pin. The sleeve reveals the major number 5 along with 3 additional subdivision lines past that number. The thimble index line aligns directly with the number 9. What is the measured diameter of the wrist pin?

0.509\text{ inch}

0.559\text{ inch}

0.584\text{ inch}

0.609\text{ inch}

Cevabı ve açıklamayı göster

Cevap: $0.584\text{ inch}$

Cevap

0.584\text{ inch}

A standard inch micrometer sleeve is marked in increments of

0.025\text{ inch}

, with numbered lines representing tenths of an inch (

0.100\text{ inch}

). The major line 5 represents

0.500\text{ inch}

, three subdivision marks represent

3 \times 0.025 = 0.075\text{ inch}

, and the thimble reading of 9 represents

0.009\text{ inch}

. Summing these values gives

0.500 + 0.075 + 0.009 = 0.584\text{ inch}

.

Adım Adım Çözüm

1

Read the largest visible major number on the sleeve scale

Major number

5 = 0.500\text{ inch}

Each numbered division on the sleeve represents tenths of an inch (

0.100\text{ inch}

).

2

Count the visible subdivision markings past the major number on the sleeve

3 \times 0.025\text{ inch} = 0.075\text{ inch}

Each small subdivision line between numbers on the sleeve equals

0.025\text{ inch}

.

3

Read the graduation line on the thimble aligned with the sleeve datum line

9 \times 0.001\text{ inch} = 0.009\text{ inch}

Each graduation mark on the thimble represents one thousandth of an inch (

0.001\text{ inch}

).

4

Sum all three scale components

0.500\text{ in} + 0.075\text{ in} + 0.009\text{ in} = 0.584\text{ inch}

The total measurement is the sum of the major sleeve reading, sleeve subdivisions, and thimble graduation.

Anahtar Kavram

Standard Inch Outside Micrometer Reading

Tahmini Süre:1m 0s

Soru 2454Soru →

A remote-controlled submersible is conducting an inspection in a freshwater lake. It initially hovers at a static depth of $10\text{ meters}$ below the surface. Later, the operator commands the submersible to descend to a depth of $3,000\text{ centimeters}$ . Assuming the water density remains constant, how does the hydrostatic pressure on the submersible at the new depth compare to the pressure at the initial depth?

The hydrostatic pressure is exactly

3\text{ times}

as great.

The hydrostatic pressure is exactly

300\text{ times}

as great.

The hydrostatic pressure remains the same because the volume of the submersible displacing the water has not changed.

The hydrostatic pressure increases exponentially because the deeper water is highly compressed to a greater density.

Cevabı ve açıklamayı göster

Cevap: The hydrostatic pressure is exactly $3\text{ times}$ as great.

Cevap

The hydrostatic pressure is exactly 3 times as great.

Hydrostatic pressure is calculated using the formula

P = \rho \cdot g \cdot h

. Because the fluid (freshwater) and gravity remain constant, the pressure is directly proportional to the depth (

h

). To accurately compare the depths, they must be in the same unit. Converting the new depth to meters (

3,000\text{ cm} = 30\text{ m}

) reveals that the submersible has gone from

10\text{ meters}

to

30\text{ meters}

. Since the depth has increased by a factor of 3, the hydrostatic pressure also increases by a factor of 3.

Adım Adım Çözüm

1

Identify the formula for hydrostatic pressure.

P = \rho \cdot g \cdot h

, meaning pressure is directly proportional to depth (

h

) when density (

\rho

) and gravity (

g

) are constant.

Establishing the mathematical relationship is necessary to compare the two states.

2

Convert the second depth into meters to match the initial depth's units.

3,000\text{ cm} \div 100\text{ cm/m} = 30\text{ meters}

.

Physical quantities must be in the same units before they can be accurately compared or divided.

3

Compare the new depth to the initial depth.

30\text{ meters} \div 10\text{ meters} = 3

.

Because the depth has tripled, the directly proportional hydrostatic pressure also triples.

Anahtar Kavram

Hydrostatic pressure in an incompressible fluid is directly proportional to its depth.

Tahmini Süre:1m 0s

Soru 2455Soru →

An aviation mechanic is using a manual sheet metal bender. The operating lever pivots on a fixed hinge at its far end. The metal sheet being bent provides resistance against the lever at a point $3\text{ inches}$ from the hinge. If the mechanic applies a perpendicular effort force of $50\text{ pounds}$ to the handle at a distance of $24\text{ inches}$ from the hinge, which of the following correctly identifies the class of this lever and the resulting force applied to the metal sheet?

Second-class lever;

400\text{ pounds}

Third-class lever;

400\text{ pounds}

First-class lever;

350\text{ pounds}

Second-class lever;

6.25\text{ pounds}

Cevabı ve açıklamayı göster

Cevap: Second-class lever; $400\text{ pounds}$

Cevap

The mechanism is a second-class lever, and the resulting force applied to the metal sheet is

400\text{ pounds}

.

In this scenario, the load (metal sheet) is positioned between the fulcrum (hinge) and the effort (mechanic's hand), which defines a second-class lever. The mechanical advantage is found by dividing the effort arm distance (

24\text{ inches}

) by the load arm distance (

3\text{ inches}

), yielding an MA of

8

. Multiplying the applied effort of

50\text{ pounds}

by the MA of

8

gives a total applied force of

400\text{ pounds}

.

Adım Adım Çözüm

1

Determine the class of the lever based on the component positions.

The hinge (fulcrum) is at one end, the effort is at the other end, and the metal sheet (load) is between them. This is the definition of a second-class lever.

Correctly identifying the lever class ensures the proper understanding of how forces and distances are distributed.

2

Calculate the Mechanical Advantage (MA) of the lever.

MA = \frac{\text{Effort Arm}}{\text{Load Arm}} = \frac{24\text{ inches}}{3\text{ inches}} = 8

Mechanical advantage dictates how much the input effort force will be multiplied by the machine.

3

Calculate the resulting force applied to the load (metal sheet).

\text{Force} = \text{Effort Force} \times MA = 50\text{ pounds} \times 8 = 400\text{ pounds}

The output force is the product of the input effort force and the mechanical advantage.

Anahtar Kavram

Lever Classification and Mechanical Advantage

Soru 2456Soru →

Why are highly hardened steel bolts typically avoided in mechanical applications subjected to heavy shock loads and constant vibrations, such as automotive suspension systems?

Highly hard materials are extremely flexible and are likely to vibrate loose from the assembly over time.

Extremely hard materials tend to be brittle and can suddenly fracture when subjected to high-impact forces.

Increasing the hardness of steel proportionally increases its ductility, causing the bolt to stretch permanently.

The high hardness causes the bolt to undergo rapid thermal expansion when exposed to friction from vibrations.

Cevabı ve açıklamayı göster

Cevap: Extremely hard materials tend to be brittle and can suddenly fracture when subjected to high-impact forces.

Cevap

Extremely hard materials tend to be brittle and can suddenly fracture when subjected to high-impact forces.

The correct answer accurately identifies the trade-off between hardness and brittleness. While hardened steel resists wear and static loads very well, it lacks the toughness required to absorb sudden kinetic energy. Instead of yielding slightly under a severe shock, a fully hardened bolt will snap, which is a catastrophic failure in an automotive suspension.

Adım Adım Çözüm

1

Analyze the mechanical requirements of the scenario.

Automotive suspension systems experience heavy shock loads and constant vibrations.

Identifying the applied forces helps determine which material properties are most critical for the component to survive.

2

Evaluate the material property in question (Hardness).

Hardness is a material's resistance to localized deformation, such as scratching or indentation. However, as steel is hardened, it typically loses its toughness and ductility.

Understanding the trade-offs of material treatments is essential for engineering component selection.

3

Relate the material property trade-offs to the required application.

Because hardened steel is brittle, a sudden shock from the suspension could exceed its ultimate tensile strength without any prior stretching, causing the bolt to snap catastrophically. Therefore, a moderately hard but tougher bolt is preferred.

Components in shock-loading environments must be able to absorb energy (toughness) rather than strictly resisting deformation.

Anahtar Kavram

Material Toughness vs. Brittleness

Tahmini Süre:1m 0s

Soru 2457Soru →

An automotive machinist is selecting specialized precision measuring tools during an engine overhaul. Which inspection task correctly matches each precision measurement instrument?

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Dial bore gauge matches cylinder bore taper and out-of-round inspection; Depth micrometer matches measuring deck-to-piston crown distance; Feeler gauge matches measuring piston ring end gap; Plastigage strip matches determining journal-to-bearing oil clearance.

Each instrument is paired with its specific geometric capability: dial bore gauges measure internal bore dimensions at depth; depth micrometers reference a flat surface to measure recessed depths; feeler gauge leaves measure narrow accessible gaps; and Plastigage measures assembled bearing journal clearances via controlled deformation.

Adım Adım Çözüm

1

Identify the instrument designed for internal cylindrical geometry variation across depth.

The dial bore gauge directly measures internal bore diameters and reveals taper and out-of-round wear.

Internal cylinder walls require a long-reach indicator with centralizing contacts to inspect multiple heights within the bore.

2

Identify the tool designed for linear downward displacement from a reference plane.

The depth micrometer provides exact linear measurements from the block deck plane down to the piston crown.

Its precision flat reference base spans the opening while the micrometer spindle measures downward distance.

3

Identify the tool designed for narrow clearance gap measurement between parallel metal faces.

The feeler gauge blade set measures piston ring end gap.

Thin calibrated steel leaves slide into narrow gaps to verify clearances within thousandths of an inch.

4

Identify the consumable precision gauge used for clamped journal oil clearances.

Plastigage determines journal-to-bearing shell clearance upon cap torquing.

The plastic thread deforms proportionally to available clearance when clamped without rotating the crankshaft.

Anahtar Kavram

Selection and application of precision automotive measuring instruments based on component geometry and tolerance type.

Tahmini Süre:1m 0s

Soru 2458Soru →

When an $80 \text{ kg}$ railway worker pushes horizontally against a stationary $4,000 \text{ kg}$ railcar, the railcar exerts a backward reaction force on the worker that is greater than the worker's forward pushing force, due to the railcar's significantly larger mass.

Doğru

Yanlış

Cevabı ve açıklamayı göster

Cevap: False

Cevap

False

The statement is false because action and reaction forces in a mechanical interaction are always exactly equal in magnitude, even when there is an extreme discrepancy between the masses of the two interacting objects.

Adım Adım Çözüm

1

Identify the two interacting bodies and the nature of the interaction.

The worker applies a forward pushing force (action) on the railcar, and the railcar applies a backward contact force (reaction) on the worker.

Forces always occur in pairs resulting from mutual interactions between two objects.

2

Evaluate the magnitude of the forces using Newton's Third Law of Motion.

The force exerted by the worker is exactly equal in magnitude to the force exerted by the railcar.

Newton's Third Law states that for every action, there is an equal and opposite reaction, regardless of differences in size, mass, or acceleration.

3

Determine if the railcar's larger mass increases its reaction force.

The mass difference does not change the force equality; it only means the railcar will experience significantly less acceleration from the same force compared to the worker.

Force equality is universally true in action-reaction pairs;

F=ma

dictates acceleration, not the initial interaction force.

Anahtar Kavram

Newton's Third Law (Action/Reaction)

Tahmini Süre:45s

Soru 2459Soru →

An automotive technician uses a standard 1- to 2-inch outside micrometer to measure the diameter of a crankshaft connecting rod journal. On the sleeve scale, the major number 6 is visible, along with 3 additional graduation lines past the 6. The thimble bevel aligns precisely with the graduation line 11. What is the total measurement indicated on the micrometer?

1.661\text{ in}

1.686\text{ in}

1.636\text{ in}

1.611\text{ in}

Cevabı ve açıklamayı göster

Cevap: $1.686\text{ in}$

Cevap

1.686\text{ in}

The correct reading of

1.686\text{ in}

is found by adding the base frame size (

1.000\text{ in}

), the sleeve major number (

0.600\text{ in}

), the three

0.025\text{ in}

sleeve subdivisions (

0.075\text{ in}

), and the thimble alignment (

0.011\text{ in}

).

Adım Adım Çözüm

1

Determine the base measurement from the micrometer's specified frame size.

1.000\text{ in}

A 1- to 2-inch micrometer starts at a baseline reading of 1.000 inch when fully closed against its anvil.

2

Read the exposed major numbered graduations on the sleeve.

6 \times 0.100\text{ in} = 0.600\text{ in}

Each numbered increment on the sleeve represents one-tenth of an inch (0.100 in).

3

Count the visible minor graduation lines past the major number 6 on the sleeve.

3 \times 0.025\text{ in} = 0.075\text{ in}

Each unnumbered subdivision line on the sleeve represents one revolution of the thimble, equal to 0.025 inch.

4

Read the thimble scale line that aligns with the sleeve index line.

11 \times 0.001\text{ in} = 0.011\text{ in}

Each line on the rotating thimble represents one-thousandth of an inch (0.001 in).

5

Sum all four components to determine the final dimension.

1.000\text{ in} + 0.600\text{ in} + 0.075\text{ in} + 0.011\text{ in} = 1.686\text{ in}

Total micrometer measurement equals base length + major sleeve + minor sleeve + thimble reading.

Anahtar Kavram

Standard inch outside micrometer scale reading and subdivision calculation

Tahmini Süre:1m 0s

Soru 2460Soru →

An engineering team evaluates different metal alloys by observing their reactions to specific mechanical stresses during laboratory testing. Match each observed behavior to the specific material property it demonstrates.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Ductility pairs with elongating under tensile stress; Malleability pairs with deforming into sheets under compressive loads; Elasticity pairs with returning to original dimensions; and Brittleness pairs with sudden fracture under impact.

Each pairing correctly aligns a fundamental mechanical property with its standard engineering definition. Ductility governs tension, malleability governs compression, elasticity governs temporary restorative deformation, and brittleness dictates failure under sudden impact.

Adım Adım Çözüm

1

Analyze the behavior involving elongation and tensile stress.

This behavior maps to Ductility.

Ductility is exclusively defined by how well a material can be drawn out (stretched) under tension without breaking.

2

Analyze the behavior involving deformation into thin sheets under compressive loads.

This behavior maps to Malleability.

Malleability dictates how a material responds to compression, such as being pressed or hammered into flat sheets.

3

Analyze the behavior involving returning to original dimensions after bending.

This behavior maps to Elasticity.

Elasticity is the tendency of solid materials to return to their original shape after being deformed.

4

Analyze the behavior involving sudden fracture under sharp impact.

This behavior maps to Brittleness.

Brittleness is the opposite of toughness and ductility; brittle materials fail suddenly with negligible plastic yielding when subjected to shock.

Anahtar Kavram

Material behavior under distinct mechanical stresses (tension, compression, impact, and bending).

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram