Tüm alıştırma soruları

Soru 2461Soru →

Sailors are using a manual capstan to pull an anchor chain. The capstan drum, around which the chain wraps, has a diameter of $1.6 \text{ feet}$ . The sailors push on the capstan bars at a horizontal distance of $4.0 \text{ feet}$ from the central axis of rotation. If the anchor chain exerts a steady pull of $1,500 \text{ pounds}$ , what is the total effort force the sailors must apply to the bars to keep the anchor moving at a constant speed? (Assume 100% efficiency and ignore friction)

600 \text{ pounds}

7,500 \text{ pounds}

300 \text{ pounds}

3,750 \text{ pounds}

Cevabı ve açıklamayı göster

Cevap: $300 \text{ pounds}$

Cevap

300 \text{ pounds}

A capstan operates as a wheel and axle mechanism. The effort is applied at a distance of

4.0 \text{ feet}

(the wheel's radius), and the load is pulled by a drum with a radius of

0.8 \text{ feet}

(half of the

1.6\text{-foot}

diameter). The Ideal Mechanical Advantage is the ratio of these radii:

4.0 / 0.8 = 5

. To find the required effort force, divide the

1,500\text{-pound}

load by the mechanical advantage of

5

, which equals

300 \text{ pounds}

.

Adım Adım Çözüm

1

Determine the radii of both the wheel (effort arm) and the axle (drum).

Wheel radius (

R

) =

4.0 \text{ feet}

. Axle radius (

r

) =

1.6 \text{ feet} / 2 = 0.8 \text{ feet}

.

The Ideal Mechanical Advantage (IMA) of a wheel and axle depends on the ratio of their radii. The problem provides the diameter of the drum, which must be halved.

2

Calculate the Ideal Mechanical Advantage (IMA) of the capstan system.

IMA = \frac{R}{r} = \frac{4.0}{0.8} = 5

.

Because the effort is applied to the larger wheel (the bars), the system multiplies the input force by a factor of 5.

3

Calculate the required effort force to overcome the load.

\text{Effort Force} = \frac{\text{Load}}{IMA} = \frac{1500}{5} = 300 \text{ pounds}

.

The effort force is the total load divided by the mechanical advantage.

Anahtar Kavram

Ideal Mechanical Advantage of a Wheel and Axle

Soru 2462Soru →

An oceanarium features a massive main saltwater tank with several viewing windows and maintenance hatches of varying sizes. Arrange the following locations in order of the hydrostatic pressure exerted by the seawater at their center points, from the lowest pressure to the highest pressure.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence from lowest to highest pressure corresponds strictly to depth: the 5-foot deep panoramic panel, the 10-foot deep porthole, the 15-foot deep observation window, and the 20-foot deep maintenance hatch.

Hydrostatic pressure is calculated based on the vertical depth below the surface. Because all windows are in the same saltwater tank, fluid density and gravity are constant. Therefore, the pressure increases linearly with depth, making the 5-foot depth the lowest pressure and the 20-foot depth the highest, regardless of the physical size of each window.

Adım Adım Çözüm

1

Recall the principles determining hydrostatic pressure in a static fluid.

Hydrostatic pressure is determined by the equation

P = \rho gh

, meaning it depends only on fluid density (

\rho

), gravity (

g

), and depth (

h

).

Establishing the governing physical rule prevents confusion from irrelevant details like window size or shape.

2

Identify the relevant variable for each location.

The relevant variable is the depth of the center point for each window: 5 ft, 10 ft, 15 ft, and 20 ft.

Extracting the depth isolates the only factor that changes hydrostatic pressure in this single, uniform tank.

3

Sort the locations by depth to determine pressure order.

Ranking from lowest depth to highest depth gives: 5 ft < 10 ft < 15 ft < 20 ft.

Since pressure is directly proportional to depth, ordering from shallowest to deepest correctly ranks the pressure from lowest to highest.

Anahtar Kavram

Hydrostatic pressure in a static fluid is directly proportional to depth and is completely independent of the total fluid volume, container shape, or the area of the surface it acts upon.

Tahmini Süre:1m 0s

Soru 2463Soru →

An automotive technician operates a hydraulic floor jack by pressing down on its handle. The handle pivots on a fixed pin at one end. The technician applies a steady downward force of $30\text{ lbs}$ at the opposite end of the handle. The total length of the handle from the pivot pin to the point of effort is $24\text{ inches}$ . The handle pushes down on a pump piston that is located $1.5\text{ inches}$ from the pivot pin. What is the total force, in pounds, applied to the pump piston? (Assume the handle is horizontal and ignore friction.)

Cevabı ve açıklamayı göster

Cevap: 480

Cevap

480

The jack handle operates as a lever with the fulcrum at one end. Because the effort is applied much further from the fulcrum than the load, the lever multiplies the applied force. The mechanical advantage is the ratio of the effort arm to the load arm (

24 / 1.5 = 16

). Multiplying the

30\text{ lbs}

of effort by a mechanical advantage of 16 yields a

480\text{ lbs}

force on the piston.

Adım Adım Çözüm

1

Identify the lever components.

Fulcrum = pivot pin; Effort Force (E) = 30 lbs; Effort Arm (d_E) = 24 inches; Load Arm (d_L) = 1.5 inches.

To apply the torque balance equation, all distances must be measured from the fulcrum.

2

Set up the torque balance equation.

E \times d_E = L \times d_L

In a static lever system, the torque generated by the effort equals the torque generated by the load.

3

Substitute the given values.

30 \times 24 = L \times 1.5

To prepare the equation for solving the unknown load force (L).

4

Solve for the load force.

720 = 1.5L \implies L = 480\text{ lbs}

Dividing the effort torque by the load arm distance yields the resulting force applied to the piston.

Anahtar Kavram

Torque Balance and Mechanical Advantage

Soru 2464Soru →

A technician uses a standard vernier caliper with 0.001-inch resolution to measure the outside diameter of a transmission output shaft. On the main beam, the zero mark on the vernier plate has moved past the 2-inch mark, past the major graduation 3 (representing 0.300 inch), and past two 0.025-inch subdivision lines. On the 25-division vernier plate, the line marked 18 aligns precisely with a graduation line on the main beam. What is the total measured diameter of the shaft in inches?

Cevabı ve açıklamayı göster

Cevap: 2.368

Cevap

The total measured diameter of the transmission output shaft is 2.368 inches.

To read a standard inch vernier caliper, sum the whole inches (

2.000\text{ in}

), the exposed tenths on the main beam (

0.300\text{ in}

), the exposed

0.025\text{-inch}

subdivisions (

2 \times 0.025\text{ in} = 0.050\text{ in}

), and the aligning vernier division (

18 \times 0.001\text{ in} = 0.018\text{ in}

). Adding these together gives

2.000 + 0.300 + 0.050 + 0.018 = 2.368\text{ inches}

.

Adım Adım Çözüm

1

Determine the whole inch and tenths-of-an-inch value from the main beam

2.300 inches

The vernier zero index mark has passed the 2-inch mark and the numbered 3 division, representing 2.300 inches.

2

Add the value of the exposed 0.025-inch beam subdivisions

0.050 inch (running total: 2.350 inches)

Two subdivision marks are visible past the 3, and each mark represents 0.025 inch (2 × 0.025 in = 0.050 in).

3

Add the vernier plate reading based on the aligned graduation mark

0.018 inch (final total: 2.368 inches)

The 18th mark on the vernier plate aligns with a beam line, representing 18 × 0.001 in = 0.018 inch.

Anahtar Kavram

Reading a 0.001-inch vernier caliper by combining the main beam whole inches, tenths, 0.025-inch subdivisions, and the aligning vernier plate division.

Alternatif Yöntem

Convert each scale value into thousandths of an inch before summing: 2000 thousandths (whole inches) + 300 thousandths (major mark 3) + 50 thousandths (two 0.025-inch increments) + 18 thousandths (vernier alignment) = 2368 thousandths, which equals 2.368 inches.

Tahmini Süre:1m 0s

Soru 2465Soru →

During a space mission in zero gravity, a compressed spring mechanism is used to separate a $10 \text{ kg}$ research probe from a $500 \text{ kg}$ main spacecraft. When the spring releases and pushes the two objects apart, which of the following statements correctly describes the interaction between them?

The main spacecraft exerts a larger force on the probe due to its greater inertia, overpowering the probe's reaction force.

The main spacecraft experiences a greater acceleration because its significantly larger mass amplifies the force applied by the spring.

Both objects experience the exact same magnitude of force, but the lighter probe undergoes a much greater acceleration.

The forces exerted on each object are equal and opposite, meaning they cancel each other out and prevent any initial acceleration.

Cevabı ve açıklamayı göster

Cevap: Both objects experience the exact same magnitude of force, but the lighter probe undergoes a much greater acceleration.

Cevap

Both objects experience the exact same magnitude of force, but the lighter probe undergoes a much greater acceleration.

According to Newton's Third Law, the force exerted on the probe is exactly equal in magnitude and opposite in direction to the force exerted on the spacecraft. However, because the probe has a much smaller mass, Newton's Second Law (

a=F/m

) dictates that it will experience a proportionally larger acceleration.

Adım Adım Çözüm

1

Analyze the forces acting on each object during the separation.

The spring applies an equal and opposite force to both the probe and the spacecraft.

Newton's Third Law of Motion states that for every action, there is an equal and opposite reaction.

2

Determine how each object's mass affects its resulting acceleration.

The

10 \text{ kg}

probe will accelerate much faster than the

500 \text{ kg}

spacecraft.

Newton's Second Law (

F=ma

) shows that acceleration is inversely proportional to mass when the force is constant (

a=F/m

).

Anahtar Kavram

Newton's Third Law (Action/Reaction)

Soru 2466Soru →

An automotive technician measures the thickness of a solid brake rotor using a standard 0 to 1-inch outside micrometer. On the sleeve, the major number 8 is visible along with 2 full subdivision marks past it. The thimble line aligned with the sleeve datum index is 17. What is the measured thickness of the brake rotor?

0.842\text{ in}

0.867\text{ in}

0.817\text{ in}

0.892\text{ in}

Cevabı ve açıklamayı göster

Cevap: $0.867\text{ in}$

Cevap

0.867\text{ in}

On a standard inch micrometer, the sleeve scale has numbered divisions representing

0.100\text{ in}

each and small subdivision marks representing

0.025\text{ in}

each. The thimble divides each revolution into 25 equal increments of

0.001\text{ in}

. Adding the major sleeve reading (

0.800\text{ in}

), the two subdivision marks (

2 \times 0.025 = 0.050\text{ in}

), and the thimble reading (

0.017\text{ in}

) yields

0.867\text{ in}

.

Adım Adım Çözüm

1

Read the major graduation on the micrometer sleeve

Major reading =

0.800\text{ in}

Each numbered mark on a standard inch micrometer sleeve represents one-tenth of an inch (

0.100\text{ in}

), so 8 represents

0.800\text{ in}

.

2

Count the visible subdivision lines on the sleeve past the major mark

Subdivision reading =

2 \times 0.025\text{ in} = 0.050\text{ in}

Each small subdivision line on the sleeve represents one revolution of the thimble, or

0.025\text{ in}

.

3

Read the thimble graduation aligned with the sleeve datum line

Thimble reading =

0.017\text{ in}

Each division on the thimble represents one-thousandth of an inch (

0.001\text{ in}

).

4

Sum all three readings to determine total thickness

0.800\text{ in} + 0.050\text{ in} + 0.017\text{ in} = 0.867\text{ in}

The total micrometer measurement is the sum of the major sleeve mark, minor sleeve subdivisions, and aligned thimble value.

Anahtar Kavram

Reading a Standard Inch Outside Micrometer

Tahmini Süre:1m 0s

Soru 2467Soru →

During the assembly of a metal aircraft framework, a technician uses a pneumatic hammer to strike the unheaded end of a solid metal rivet. The repeated impacts successfully flatten the end of the cylinder to form a permanent locking head without cracking or splintering the material. Which material property primarily allows the rivet to undergo this permanent deformation under compressive force?

Hardness

Malleability

Ductility

Elasticity

Cevabı ve açıklamayı göster

Cevap: Malleability

Cevap

The correct property is malleability.

Malleability is the physical property that allows a solid to bend or be hammered into other shapes without breaking. Because the pneumatic hammer applies compressive stress to flatten the rivet, malleability is the exact property required for this process.

Adım Adım Çözüm

1

Identify the type of force being applied in the scenario.

The pneumatic hammer applies a crushing, compressive force to the rivet.

Different material properties govern how a substance reacts to different types of applied forces (e.g., tension vs. compression).

2

Analyze the required outcome of the deformation.

The rivet must flatten into a new shape permanently (plastic deformation) without breaking or cracking.

If the deformation were temporary, the rivet would not lock the joint. If the material fractured, the joint would fail.

3

Match the observed behavior to the corresponding material property definitions.

The ability to deform plastically under compressive stress without fracturing defines malleability.

This distinguishes it from ductility (tensile stress) and elasticity (temporary deformation).

Anahtar Kavram

Malleability vs. other structural material properties

Tahmini Süre:1m 0s

Soru 2468Soru →

At a commercial fuel distribution center, two open-top vertical storage tanks hold the exact same grade of liquid diesel. Tank X is a wide cylinder with a $12\text{-meter}$ base diameter. Tank Y is a tall, narrow cylinder with a $2\text{-meter}$ base diameter. Both tanks are currently filled with diesel to an exact depth of $8\text{ meters}$ . Which of the following statements correctly compares the hydrostatic pressure exerted by the fuel on the bottom surface of each tank?

The pressure is identical in both tanks, because hydrostatic pressure depends only on fluid depth and density.

The pressure in Tank X is greater, because it contains a much larger total weight and volume of fuel.

The pressure in Tank Y is greater, because the narrower base restricts the fuel and concentrates its force.

The pressure cannot be compared without first calculating the total surface area of the tank walls.

Cevabı ve açıklamayı göster

Cevap: The pressure is identical in both tanks, because hydrostatic pressure depends only on fluid depth and density.

Cevap

The pressure is identical in both tanks, because hydrostatic pressure depends only on fluid depth and density.

Hydrostatic pressure is determined by the formula

P = \rho gh

(where

\rho

is fluid density,

g

is gravity, and

h

is vertical fluid depth). Because both tanks hold the exact same fluid at the exact same depth, the pressure at the bottom is identical. The overall width, shape, or total volume of the tank does not affect hydrostatic pressure.

Adım Adım Çözüm

1

Identify the standard formula for calculating hydrostatic pressure.

P = \rho \cdot g \cdot h

(Pressure = density

\times

gravity

\times

depth).

To determine which physical variables actually affect the pressure at the bottom of the fluid column.

2

Analyze the variables provided for both storage tanks.

Both tanks contain the exact same diesel fuel (identical density,

\rho

) and are filled to the same

8\text{-meter}

level (identical depth,

h

).

To compare the factors that influence hydrostatic pressure in this specific scenario.

3

Evaluate the effect of the different tank diameters (

12\text{ meters}

vs.

2\text{ meters}

).

The diameters and total fluid volumes do not appear in the hydrostatic pressure formula and therefore have no effect on the bottom pressure.

To confirm that the shape and width of the container are irrelevant to hydrostatic pressure at a given depth.

Anahtar Kavram

Hydrostatic pressure at a given depth depends strictly on the density of the fluid and the vertical depth itself, regardless of the container's shape, base width, or total fluid volume.

Soru 2469Soru →

In workshop layout and fabrication, different tools are specialized for geometric alignment, marking, and transferring dimensions. Match each standard measurement or layout tool with its primary workshop application.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Plumb bob pairs with establishing a true, gravity-referenced vertical alignment line; Trammel points pair with scribing large circles and layout arcs beyond standard dividers; Scratch awl pairs with scribing fine, permanent layout lines; Try square pairs with checking edge squareness and marking 90-degree lines.

Each tool corresponds to its defined workshop role: a plumb bob creates vertical reference lines using gravity, trammel points clamp to beams for oversized circle and arc layouts, a scratch awl produces fine etched guide lines, and a try square checks and marks right angles.

Adım Adım Çözüm

1

Analyze the mechanical configuration and primary function of each layout and marking tool.

Identified tools that provide angular verification, vertical gravity alignment, fine scribing, and large-radius dimension transfer.

Standard shop tools are engineered with distinct geometries to fulfill dedicated layout operations.

2

Match the gravity-based vertical alignment tool.

The plumb bob pairs with establishing a true vertical line.

A suspended weight naturally hangs perfectly vertical due to gravitational pull.

3

Match the beam-mounted layout tool for large radii.

Trammel points pair with scribing large arcs and circles.

Standard dividers are constrained by their leg length, whereas trammel heads mounted on a beam span large distances.

4

Match the pointed line-marking tool and the fixed right-angle inspection tool.

The scratch awl pairs with scribing fine layout lines, while the try square pairs with 90-degree checking and marking.

An awl's point etches narrow guide grooves that prevent pencil-width inaccuracies, and a try square's rigid fixed blade verifies perpendicularity.

Anahtar Kavram

Identifying the distinct functions and mechanical applications of standard shop layout, marking, and alignment tools.

Tahmini Süre:1m 0s

Soru 2470Soru →

Determine the acceleration for each of the military transport operations described below. Sequence the operations from the lowest rate of acceleration to the highest.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct order from lowest to highest acceleration is: Naval destroyer, Armored personnel carrier, Transport plane, and Rescue helicopter.

By systematically calculating the acceleration for each scenario using the formula

a = \frac{v_f - v_i}{t}

, we can determine their respective values and order them properly. The naval destroyer evaluates to

0.5 \text{ m/s}^2

, the armored personnel carrier evaluates to

2.0 \text{ m/s}^2

, the transport plane evaluates to

4.0 \text{ m/s}^2

, and the rescue helicopter evaluates to

5.0 \text{ m/s}^2

. Placing these in ascending order yields the correct sequence.

Adım Adım Çözüm

1

Calculate the acceleration of the naval destroyer.

a = \frac{15 - 5}{20} = 0.5 \text{ m/s}^2

Using the formula

a = \frac{v_f - v_i}{t}

2

Calculate the acceleration of the armored personnel carrier.

a = \frac{22 - 10}{6} = 2.0 \text{ m/s}^2

Using the formula

a = \frac{v_f - v_i}{t}

3

Calculate the acceleration of the transport plane.

a = \frac{60 - 0}{15} = 4.0 \text{ m/s}^2

Using the formula

a = \frac{v_f - v_i}{t}

, remembering that 'from rest' means an initial velocity of

0 \text{ m/s}

4

Calculate the acceleration of the rescue helicopter.

a = \frac{45 - 0}{9} = 5.0 \text{ m/s}^2

Using the formula

a = \frac{v_f - v_i}{t}

, remembering that 'from rest' means an initial velocity of

0 \text{ m/s}

5

Sequence the vehicles by their calculated acceleration values from lowest to highest.

0.5 < 2.0 < 4.0 < 5.0

To satisfy the condition of ordering from lowest rate to highest rate.

Anahtar Kavram

Acceleration is the rate of change of velocity over time, calculated using the formula

a = \frac{v_f - v_i}{t}

.

Soru 2471Soru →

A machinist needs to locate and scribe the exact center point on the end of a round steel bar before drilling. Which component of a combination square set is specifically designed to straddle cylindrical stock and bisect its circular cross-section?

Protractor head

Center head

Square head

Trammel head

Cevabı ve açıklamayı göster

Cevap: Center head

Cevap

Center head

The center head attachment fits onto a standard steel rule and has two symmetrical arms forming a V-notch. When placed against a cylindrical workpiece, the edge of the attached blade automatically bisects the circular cross-section. Scribing two lines at different angles produces an intersection at the exact center of the round bar.

Adım Adım Çözüm

1

Identify the workpiece geometry and the required layout task.

The workpiece is a round cylinder, and the objective is finding the center point on its end face.

Choosing the correct layout tool depends directly on the geometry of the workpiece.

2

Analyze the specialized attachments available in a standard combination square set.

A combination set includes a square head (for 90-degree and 45-degree flat layouts), a protractor head (for variable angles), and a center head (with a V-shaped notch).

The center head has two arms forming an angle that positions the attached rule exactly along the diameter of any round stock placed inside it.

3

Determine the layout procedure with the center head.

Scribing a line along the rule, rotating the head roughly 90 degrees, and scribing a second line creates an intersection at the exact geometric center.

Two intersecting diameters pinpoint the true center of a circle.

Anahtar Kavram

Identifying combination square attachments and their specific layout functions

Tahmini Süre:45s

Soru 2472Soru →

An angler is reeling in a catch and holds the fishing rod perfectly horizontal. The butt of the rod is braced firmly against the angler's waist, which acts as the pivot point. The angler's top hand applies an upward lifting force $2 \text{ feet}$ away from the waist. If the fish creates a constant downward pull of $15 \text{ lbs}$ at the rod's tip, which is exactly $8 \text{ feet}$ away from the pivot point, how much upward effort force must the angler's top hand exert to maintain the rod's horizontal position? (Assume the weight of the rod itself is negligible.)

120 \text{ lbs}

60 \text{ lbs}

45 \text{ lbs}

3.75 \text{ lbs}

Cevabı ve açıklamayı göster

Cevap: $60 \text{ lbs}$

Cevap

60 \text{ lbs}

In a third-class lever, the effort is located between the fulcrum and the load. To maintain equilibrium, the effort torque must equal the load torque. Since the effort arm (

2 \text{ feet}

) is one-quarter the length of the load arm (

8 \text{ feet}

), the mechanical advantage is

0.25

. Therefore, the required effort force must be four times the load force (

15 \text{ lbs} \times 4 = 60 \text{ lbs}

).

Adım Adım Çözüm

1

Identify the lever class and pivot point.

The waist is the fulcrum, the top hand is the effort, and the fish is the load. This is a third-class lever.

Understanding the arrangement is required to correctly measure distances for the torque equation.

2

Calculate the torque exerted by the load (the fish).

\text{Load Torque} = 15 \text{ lbs} \times 8 \text{ ft} = 120 \text{ lb-ft}

.

Torque is the product of force and distance from the fulcrum.

3

Set the effort torque equal to the load torque to find the required force.

\text{Effort} \times 2 \text{ ft} = 120 \text{ lb-ft}

, which means

\text{Effort} = 60 \text{ lbs}

.

For the rod to remain horizontally stable, the opposing torques must be perfectly balanced.

Anahtar Kavram

Third-Class Levers and Torque Equilibrium

Alternatif Yöntem

Calculate the Mechanical Advantage (MA) first:

\text{MA} = \frac{\text{Effort Arm}}{\text{Load Arm}} = \frac{2}{8} = 0.25

. Then find the effort using

\text{Effort} = \frac{\text{Load}}{\text{MA}} = \frac{15}{0.25} = 60 \text{ lbs}

.

Tahmini Süre:1m 0s

Soru 2473Soru →

A structural material that possesses exceptionally high compressive strength will inherently exhibit an equally high tensile strength when subjected to pulling forces.

Doğru

Yanlış

Cevabı ve açıklamayı göster

Cevap: False

Cevap

False

The statement is false because the ability of a material to withstand being crushed (compressive strength) does not guarantee its ability to withstand being stretched (tensile strength). Concrete and cast iron are classic examples of materials that are extremely strong in compression but weak in tension.

Adım Adım Çözüm

1

Define the terms compressive strength and tensile strength in the context of structural materials.

Compressive strength is a material's resistance to being crushed or pushed together, while tensile strength is its resistance to being stretched or pulled apart.

Clarifying the specific definitions of these forces is necessary to evaluate how materials respond to them.

2

Evaluate the claim that high performance in compression guarantees equally high performance in tension.

Determine that the claim is false by recalling common real-world structural materials that behave asymmetrically.

Identifying valid counterexamples, such as concrete (which requires steel rebar specifically to compensate for its poor tensile strength), proves that the two properties are not inherently linked.

Anahtar Kavram

Compressive vs. Tensile Strength

Soru 2474Soru →

Match each wheel and axle concept to its correct definition or mechanical characteristic.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

The correct matches are: Wheel and Axle System pairs with its definition of two rotating circular objects; Ideal Mechanical Advantage (IMA) pairs with the ratio of input radius to output radius; Force Multiplier Setup pairs with effort applied to the larger wheel; and Distance/Speed Multiplier Setup pairs with effort applied to the smaller axle.

Each concept describes a specific operational mode or structural property of the wheel and axle. The fundamental physical relationship dictates that applying effort to the larger diameter (wheel) multiplies force at the expense of distance, while applying effort to the smaller diameter (axle) multiplies speed and distance at the expense of force. The mathematical ratio of these radii determines the exact Ideal Mechanical Advantage.

Adım Adım Çözüm

1

Identify the basic definition of the wheel and axle system.

It is matched as a simple machine with two connected circular objects of different radii rotating together.

Establishes the structural baseline for the mechanism.

2

Determine how Ideal Mechanical Advantage (IMA) is calculated for rotational machines.

IMA is matched to the ratio of the input component's radius to the output component's radius.

IMA represents the theoretical multiplication factor of the machine based on lever arms.

3

Analyze the conditions for a force multiplier setup.

It is matched to the scenario where effort is on the larger wheel, resulting in greater output force at the smaller axle (MA > 1).

A larger input radius creates a longer effective lever arm for the effort.

4

Analyze the conditions for a distance/speed multiplier setup.

It is matched to the scenario where effort is on the smaller axle, resulting in greater output speed at the larger wheel (MA < 1).

One rotation of the small input axle forces the large outer wheel to travel a much larger circumference in the same amount of time.

Anahtar Kavram

Mechanical principles and force-distance trade-offs of the wheel and axle simple machine.

Soru 2475Soru →

A fabricator is using a pair of layout dividers to step off and mark $5$ equally spaced hole centers in a straight line on a metal workpiece. The total distance from the center of the first hole to the center of the fifth hole is $14\text{ inches}$ . What is the required divider setting, in inches, between consecutive hole centers?

Cevabı ve açıklamayı göster

Cevap: 3.5

Cevap

The divider points must be set to

3.5\text{ inches}

.

The correct answer is

3.5\text{ inches}

because

5

equally spaced hole centers define

4

equal intervals along the line (

5 - 1 = 4

). Dividing the

14\text{-inch}

span by

4

gives exactly

3.5\text{ inches}

per interval.

Adım Adım Çözüm

1

Determine the number of equal intervals between the hole centers.

There are

4

intervals between

5

collinear points (

5 - 1 = 4

).

When stepping off positions with dividers between defined endpoints, the number of intervals is always one less than the number of points.

2

Divide the total measured span by the number of intervals.

\frac{14\text{ inches}}{4} = 3.5\text{ inches}

Equal divider spacing requires distributing the total span across the

4

equal intervals.

Anahtar Kavram

Using layout dividers to step off equal intervals along a layout line

Tahmini Süre:1m 0s

Soru 2476Soru →

Match each set of unassembled components with the correct description of their final assembled figure. Ensure all corresponding multi-point alignment markers perfectly match.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Set 1 matches the full circle requiring a 180-degree rotation. Set 2 matches the horizontal rectangle requiring translation. Set 3 matches the solid large square. Set 4 matches the composite triangle requiring a 90-degree rotation.

Each component set contains specific geometries and multi-point markers that dictate exactly one assembly method. By tracing how the points must connect (X to X, dot to dot), we can determine whether the pieces require direct translation (sliding), a 90-degree rotation, or a 180-degree rotation to assemble the composite figure.

Adım Adım Çözüm

1

Analyze Set 1's semi-circles and their markers.

Identify that the X and Y markers are reversed relative to each other, necessitating a 180-degree rotation to align them.

Without rotation, X would align with Y, which is an incorrect multi-point connection.

2

Analyze Set 2's squares and their markers.

Identify that the markers are on the right edge of Square A and the left edge of Square B.

This means they can be pushed directly together side-by-side without rotation to form a rectangle.

3

Analyze Set 3's L-shaped geometry and small rectangle.

Identify that the small piece perfectly fills the cutout space in the large piece.

Matching the star markers slots the piece into the negative space, completing the square.

4

Analyze Set 4's right triangles.

Identify that the connection markers are on perpendicular legs (vertical vs. horizontal).

A 90-degree rotation is required to make a horizontal leg vertical (or vice versa) to align the diamond markers.

Anahtar Kavram

Multi-Point Alignment and Mental Rotation

Soru 2477Soru →

A hydrostatic pressure sensor at the bottom of an upright agricultural water cistern reads $45\text{ psi}$ when the water depth is $30\text{ feet}$ . During a dry season, the water level drops to a depth of $18\text{ feet}$ . Assuming the fluid density remains constant, what is the new hydrostatic pressure reading in $\text{psi}$ at the sensor?

Cevabı ve açıklamayı göster

Cevap: 27

Cevap

27

Since hydrostatic pressure is directly proportional to depth (

P = \rho \cdot g \cdot h

), the ratio of pressure to depth remains constant. The initial ratio is

45\text{ psi} / 30\text{ feet} = 1.5\text{ psi/ft}

. At a new depth of

18\text{ feet}

, the pressure is

18\text{ feet} \times 1.5\text{ psi/ft} = 27\text{ psi}

.

Adım Adım Çözüm

1

Identify the relationship between hydrostatic pressure and fluid depth.

Hydrostatic pressure is directly proportional to the depth of the fluid.

The formula for hydrostatic pressure is

P = \rho \cdot g \cdot h

, meaning if density (

\rho

) and gravity (

g

) are constant, the pressure changes linearly with depth (

h

).

2

Determine the pressure per foot of water depth.

45\text{ psi} \div 30\text{ feet} = 1.5\text{ psi}

per foot.

This establishes the constant of proportionality for the fluid in this specific cistern.

3

Calculate the new pressure at the reduced depth.

1.5\text{ psi/foot} \times 18\text{ feet} = 27\text{ psi}

.

Multiplying the pressure per foot by the new depth yields the corresponding hydrostatic pressure.

Anahtar Kavram

Hydrostatic pressure is directly proportional to fluid depth.

Soru 2478Soru →

A metalworker needs to scribe a line parallel to the true edge of a flat plate at a preset distance. Which standard layout tool features one pointed scribing leg and one bent leg designed to ride along the edge of the workpiece?

Outside caliper

Hermaphrodite caliper

Trammel points

Spring dividers

Cevabı ve açıklamayı göster

Cevap: Hermaphrodite caliper

Cevap

Hermaphrodite caliper

The hermaphrodite caliper (also called an odd-leg caliper) is specially manufactured with one curved or bent leg that acts as a guide against the edge of a workpiece and one straight pointed leg that scribes a clean line exactly parallel to that reference edge.

Adım Adım Çözüm

1

Identify the specific mechanical requirement of the layout task.

The task requires guiding a tool along a finished reference edge while simultaneously scribing a line at a constant parallel offset.

Selecting the correct workshop layout tool depends on matching its physical geometry to the referencing and marking requirements.

2

Evaluate standard layout tool configurations against the task requirements.

A hermaphrodite caliper (odd-leg caliper) has one bent leg that hooks against a reference edge and one straight pointed leg that scribes parallel to that edge.

Standard dividers and outside calipers lack the hooked guide leg required to maintain a consistent offset along an edge.

Anahtar Kavram

Identification and proper application of layout and scribing tools for parallel edge marking

Tahmini Süre:1m 0s

Soru 2479Soru →

Match each operational adjustment made to a mechanical lever system with its correct effect on the system's mechanical advantage.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Grasping the pry bar further out increases the effort arm. Shifting the wheelbarrow load closer to the wheel decreases the load arm. Pinching tweezers closer to the hinge decreases the effort arm. Doubling all proportions maintains the original ratio.

Mechanical advantage for any lever is calculated by dividing the length of the effort arm by the length of the load arm (

MA = \frac{d_e}{d_l}

). Any adjustment that increases the effort arm or decreases the load arm will result in a higher mechanical advantage, making the work feel easier. Conversely, reducing the effort arm or increasing the load arm lowers the mechanical advantage. Proportional changes to both arms maintain the exact same ratio.

Adım Adım Çözüm

1

Recall the formula for Mechanical Advantage (MA) of a lever.

MA = \frac{\text{Effort Arm}}{\text{Load Arm}}

.

This fundamental relationship determines how any physical adjustment to the lever's dimensions will affect the required force.

2

Analyze the pry bar adjustment.

Grasping the tool further from the fulcrum increases the numerator (Effort Arm), which increases the overall MA.

A higher MA means less force is required to move the same load.

3

Analyze the wheelbarrow adjustment.

The wheel is the fulcrum. Moving the load closer to the wheel decreases the denominator (Load Arm), which increases the overall MA.

A smaller denominator results in a larger ratio, requiring less lifting force at the handles.

4

Analyze the tweezers adjustment.

Tweezers are a third-class lever with the fulcrum at the joined end. Pinching closer to the joined end decreases the Effort Arm.

Decreasing the numerator lowers the MA, meaning more pinch force is required, though the tips will close faster and over a larger distance.

5

Analyze the proportional scaling adjustment.

If both the effort arm and load arm are multiplied by 2, the new MA is

\frac{2 \times \text{Effort Arm}}{2 \times \text{Load Arm}}

.

The factor of 2 cancels out, leaving the mechanical advantage exactly the same as the original lever.

Anahtar Kavram

Mechanical Advantage Ratio and Lever Adjustments

Soru 2480Soru →

A technician is operating a large industrial pipeline valve. The valve's central stem, which acts as the axle, has a diameter of $3 \text{ inches}$ . The handwheel attached to the stem has a radius of $12 \text{ inches}$ . If the technician applies a tangential effort force of $60 \text{ pounds}$ to the outer edge of the handwheel, what is the resulting output force applied to the valve stem?

7.5 \text{ pounds}

480 \text{ pounds}

240 \text{ pounds}

960 \text{ pounds}

Cevabı ve açıklamayı göster

Cevap: $480 \text{ pounds}$

Cevap

The resulting output force is

480 \text{ pounds}

.

The correct answer accurately calculates the mechanical advantage by first finding the axle's radius (

1.5 \text{ inches}

), then dividing the wheel's radius (

12 \text{ inches}

) by the axle's radius to get an Ideal Mechanical Advantage (IMA) of

8

. Multiplying this IMA by the

60 \text{ pounds}

of input force yields an output force of

480 \text{ pounds}

.

Adım Adım Çözüm

1

Determine the radius of the axle.

Axle radius =

3 \text{ inches} \div 2 = 1.5 \text{ inches}

.

Mechanical advantage must be calculated using the same dimension type for both components (either both radii or both diameters). The stem provided the wheel's radius but the axle's diameter.

2

Calculate the Ideal Mechanical Advantage (IMA) of the wheel and axle system.

IMA =

\frac{12 \text{ inches}}{1.5 \text{ inches}} = 8

.

IMA is the ratio of the radius of the wheel (input) to the radius of the axle (output).

3

Calculate the output force applied to the valve stem.

Output Force =

8 \times 60 \text{ pounds} = 480 \text{ pounds}

.

The output force is the product of the input effort force and the mechanical advantage.

Anahtar Kavram

The mechanical advantage of a wheel and axle is determined by the ratio of their radii (or diameters), which multiplies the input force to overcome a larger load.

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Alternatif Yöntem

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Alternatif Yöntem

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap