Tüm alıştırma soruları

Soru 361Soru →

Review the following mechanical fastening scenarios. Match each scenario to the primary type of stress or characteristic failure mode it is most likely to experience.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Overlapping pulled plates experience single shear stress; over-tightened bolts suffer excessive tension; keyed pulleys transfer torsional shear stress; and alternating bending cycles lead to metal fatigue.

Each scenario describes a distinct physical loading condition. Overlapping plates pulled in opposite directions slice across the bolt (single shear). Torquing a nut stretches the bolt shaft along its length (tension). A rotating shaft transferring power through a key creates a twisting sideways force (torsional shear). Continuous bending back and forth causes microscopic damage over time (fatigue).

Adım Adım Çözüm

1

Analyze the overlapping plates scenario.

Identified that parallel pulling forces on overlapping joined plates create a slicing or cutting action (shear) across the fastener.

This is the classic definition of a lap joint in single shear.

2

Analyze the over-tightening scenario.

Identified that tightening a nut draws it up the bolt threads, pulling the bolt shaft lengthwise.

Applying torque translates into clamping force, which places the bolt shaft under tensile stress (tension).

3

Analyze the keyed pulley scenario.

Identified that the key prevents the pulley from slipping on the spinning shaft, transferring rotational force.

The transfer of rotational motion creates a twisting shear force known as torsional stress on the key.

4

Analyze the alternating bending scenario.

Identified that continuous, repeating stress cycles cause microscopic wear within the metal structure.

Cyclic loading is the primary cause of metal fatigue, especially where stress risers like threads exist.

Anahtar Kavram

Identifying the specific types of mechanical stress (shear, tension, torsion, fatigue) applied to fasteners in different operating environments.

Soru 362Soru →

Match each physical scenario or material choice with its corresponding principle of thermal radiation.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Highly polished aluminum shield matches with reflecting radiant heat; Matte black coating matches with maximizing emission; Vacuum matches with exclusive electromagnetic transfer; Glossy white paint matches with minimizing solar absorption.

Each scenario correctly pairs a physical characteristic (surface color, finish, or presence of a vacuum) with its mechanical consequence regarding the absorption, reflection, or transmission of thermal radiation.

Adım Adım Çözüm

1

Analyze the thermal properties of a highly polished aluminum shield.

Shiny, smooth metals reflect most incoming radiation.

To match it with its function of protecting adjacent components by reflecting heat.

2

Evaluate the thermal behavior of a matte black surface in a vacuum.

Dark, dull surfaces are excellent emitters of radiation.

To match the satellite panel with its primary purpose of maximizing heat emission into space.

3

Consider the mechanism of heat transfer through a complete vacuum.

Only radiation (electromagnetic waves) can travel without a physical medium.

To match the Earth-Sun vacuum with the fact that it permits transfer exclusively via electromagnetic waves.

4

Determine the thermal effect of glossy white paint on a storage tank exposed to the sun.

White surfaces reflect visible light and effectively reduce heat absorption.

To match the white paint with the minimization of incoming solar radiation absorption.

Anahtar Kavram

Surface finish and color dictate how materials reflect, absorb, and emit thermal radiation, which travels via electromagnetic waves and can propagate through a vacuum.

Soru 363Soru →

Match each wheel and axle configuration to its resulting Ideal Mechanical Advantage (IMA).

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Match each configuration by correctly dividing the effort radius by the load radius.

The correct matches are found by calculating the ratio of the input (effort) distance to the output (load) distance. For a wheel and axle, this is equivalent to

\frac{\text{Effort Radius}}{\text{Load Radius}}

. When the effort is on the wheel, the IMA is greater than 1. When the effort is on the axle, the IMA is less than 1.

Adım Adım Çözüm

1

Identify the effort radius and the load radius for each given configuration.

You determine whether the force is applied to the wheel (larger radius) or the axle (smaller radius).

The location of the applied force dictates which radius is the numerator in the IMA formula.

2

Apply the Ideal Mechanical Advantage formula:

\text{IMA} = \frac{\text{Effort Radius}}{\text{Load Radius}}

.

Calculations yield

5

,

4

,

0.5

, and

0.2

for the respective configurations.

This formula provides the theoretical multiplication of force for a wheel and axle mechanism.

Anahtar Kavram

Ideal Mechanical Advantage of a Wheel and Axle

Tahmini Süre:45s

Soru 364Soru →

An engineering team is evaluating the efficiency and safety of a newly designed transport vehicle. Match each mechanical situation observed during testing to the primary type of frictional resistance dominating that situation.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Tires resting without slipping match with static friction. The aerodynamic body pushing through winds matches with fluid friction. Locked wheels skidding match with kinetic friction. Cylindrical bearings match with rolling friction.

Each mechanical situation directly illustrates one of the four primary types of friction: static (no relative motion), kinetic (continuous sliding), rolling (rotating elements), and fluid (resistance through a gas or liquid).

Adım Adım Çözüm

1

Analyze the sloped ramp scenario.

Identified no relative motion between the tires and the ramp.

Surfaces at rest relative to each other experience static friction.

2

Analyze the high-speed wind scenario.

Identified interaction between a solid moving body and a gas (air).

Gases and liquids behave as fluids, meaning aerodynamic drag is a form of fluid friction.

3

Analyze the emergency stop scenario.

Identified the tires locking and sliding continuously across the pavement.

Active sliding between two solid surfaces characterizes kinetic friction.

4

Analyze the axle bearing scenario.

Identified cylindrical elements rotating to facilitate movement.

The rotation of cylinders or spheres between surfaces is the defining characteristic of rolling friction.

Anahtar Kavram

Frictional Resistance Types and Applications

Soru 365Soru →

Wheel and axle mechanisms can be designed to multiply either force or speed. Match each real-world application of a wheel and axle to its correct mechanical description.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Doorknob matches the internal latch description; Automobile drive wheels match the engine and tire description; Manual hand winch matches the handle and cable drum description; Ceiling fan matches the motor and blades description.

Each mechanism uses the wheel and axle principle based on its specific need. The doorknob and hand winch are force multipliers because effort is applied to the larger wheel. The drive wheels and ceiling fan are speed multipliers because effort is applied to the smaller axle.

Adım Adım Çözüm

1

Identify the mechanisms that act as force multipliers (input on the wheel).

The doorknob and manual hand winch both receive input force on the larger radius to produce a larger output force on the smaller radius.

Determining the location of the input force helps classify the mechanical advantage.

2

Identify the mechanisms that act as speed multipliers (input on the axle).

The automobile drive wheels and ceiling fan both receive input force on the smaller central radius to produce greater speed at the larger outer radius.

Speed multipliers take advantage of the larger circumference of the wheel covering more distance in the same amount of time.

3

Pair each specific device with its corresponding functional description.

The doorknob operates an internal latch; the drive wheels rotate the outer tire; the winch winds a cable around a drum; the ceiling fan spins blades.

Matching the physical components completes the logical pairing for each wheel and axle application.

Anahtar Kavram

Force Multipliers vs. Speed Multipliers in Wheel and Axle Systems

Soru 366Soru →

Match the following types of gear components to their primary mechanical function within a transmission system.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Rack and pinion maps to converting rotational to linear motion. Worm gear maps to providing drastic speed reduction and preventing back-driving. Bevel gear maps to changing the axis of rotation by 90 degrees. Idler gear maps to reversing rotational direction without changing the final output speed ratio.

Each gear type serves a distinct mechanical purpose: rack and pinions handle linear conversion, worm gears manage high reduction and locking, bevel gears handle angular power transmission, and idlers handle direction reversal without ratio changes.

Adım Adım Çözüm

1

Identify the unique function of a rack and pinion system.

Matches with converting rotational motion into linear motion.

The circular pinion rolls along the flat rack, pushing it in a straight line, which is unique among these options.

2

Identify the primary characteristic of a worm gear drive.

Matches with providing drastic speed reduction and preventing back-driving.

The screw-like thread of the worm advances the gear by one tooth per revolution, giving high reduction, and friction usually prevents reverse operation.

3

Identify the application of a bevel gear set.

Matches with changing the axis of rotation by 90 degrees between intersecting shafts.

The conical shape of bevel gears allows them to mesh at an angle, most commonly 90 degrees, allowing perpendicular power transmission.

4

Identify the purpose of an idler gear.

Matches with reversing the rotational direction without changing the final output speed ratio.

An intermediate gear only changes the spin direction of the subsequent gear; its tooth count cancels out in the overall ratio calculation.

Anahtar Kavram

Functions of specialized gear types in power transmission

Soru 367Soru →

Match each flight deck towing and movement scenario to its resulting acceleration using Newton's Second Law ( $F = ma$ ). Assume no friction unless stated.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

The correct matches pair the aircraft with

0.8 \text{ m/s}^2

, the munitions cart with

4.0 \text{ m/s}^2

, the helicopter with

0.25 \text{ m/s}^2

, and the fuel pod with

1.2 \text{ m/s}^2

.

Each acceleration is determined by dividing the net force acting on the object by its mass. In scenarios where multiple forces act on the object, the net force must be found first by subtracting any resistance from the applied force.

Adım Adım Çözüm

1

Calculate the acceleration for the aircraft.

Dividing the net force of

11,200 \text{ N}

by the mass of

14,000 \text{ kg}

yields

0.8 \text{ m/s}^2

.

Applying Newton's Second Law directly.

2

Calculate the acceleration for the munitions cart.

Dividing the net force of

12,800 \text{ N}

by the mass of

3,200 \text{ kg}

yields

4.0 \text{ m/s}^2

.

Applying Newton's Second Law directly.

3

Determine the net force and calculate the acceleration for the helicopter.

Subtract the

2,000 \text{ N}

resistance from the

6,000 \text{ N}

applied force to find a net force of

4,000 \text{ N}

. Dividing this by the

16,000 \text{ kg}

mass gives

0.25 \text{ m/s}^2

.

Newton's Second Law requires the net force, which is the sum of all opposing forces.

4

Calculate the acceleration for the fuel pod.

Dividing the net force of

4,800 \text{ N}

by the mass of

4,000 \text{ kg}

yields

1.2 \text{ m/s}^2

.

Applying Newton's Second Law directly.

Anahtar Kavram

Newton's Second Law (

F = ma

)

Tahmini Süre:1m 30s

Soru 368Soru →

Match each practical material or component to its primary thermal property or mechanism.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Engine coolant pairs with high specific heat capacity; Aluminum radiator fins pair with high thermal conductivity and low specific heat; Fiberglass batting pairs with trapping pockets of air; Spacecraft ceramic tiles pair with extremely low thermal conductivity.

Each material is chosen for mechanical applications based on distinct thermal properties. Water's high specific heat makes it an ideal coolant. Aluminum's high conductivity allows it to act as an effective heat sink and radiator. Fiberglass relies on the low conductivity of trapped air for home insulation. Ceramics provide robust thermal resistance for extreme environments.

Adım Adım Çözüm

1

Analyze the thermal requirements for engine coolant.

Coolant must absorb a lot of heat without vaporizing, which requires a high specific heat capacity.

This corresponds to the property of absorbing large amounts of thermal energy with minimal temperature increase.

2

Analyze the function of aluminum radiator fins.

Fins are designed to pull heat away from the coolant and release it into the air quickly.

This requires high thermal conductivity to move the heat, and low specific heat so the aluminum itself doesn't hold onto the thermal energy.

3

Analyze how fiberglass batting insulates buildings.

Fiberglass is mostly empty space filled with air.

Air is a poor thermal conductor. By trapping air in small pockets, fiberglass prevents convective currents and minimizes conductive heat transfer.

4

Analyze the purpose of spacecraft ceramic tiles.

Tiles must protect the spacecraft interior from the extreme heat of atmospheric re-entry.

Ceramics have incredibly low thermal conductivity, meaning heat struggles to pass through them, effectively shielding underlying structures.

Anahtar Kavram

Different applications require specific thermal properties, such as high heat capacity for absorbing energy, high conductivity for dissipating energy, or low conductivity for insulation.

Soru 369Soru →

A base quartermaster is evaluating the fuel efficiency of four different portable power generators. Match each generator's fuel consumption data to its correct unit rate in gallons per hour.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Generator W matches with

3.5

gallons per hour, Generator X matches with

3.75

gallons per hour, Generator Y matches with

6.5

gallons per hour, and Generator Z matches with

2.25

gallons per hour.

Each generator's fuel consumption is converted to an hourly rate by matching the time period into hours (e.g.,

2

days to

48

hours,

240

minutes to

4

hours) and then dividing the total gallons consumed by the total hours.

Adım Adım Çözüm

1

Calculate the unit rate for Generator W.

14 \div 4 = 3.5

gallons per hour.

The rate is already given in hours, so divide the total gallons by the total hours.

2

Calculate the unit rate for Generator X by converting days to hours.

2

days =

48

hours.

180 \div 48 = 3.75

gallons per hour.

The unit rate must be in gallons per hour, so the time must first be converted from days to hours.

3

Calculate the unit rate for Generator Y.

26 \div 4 = 6.5

gallons per hour.

Divide the total volume of fuel by the given time in hours.

4

Calculate the unit rate for Generator Z by converting minutes to hours.

240

minutes =

4

hours.

9 \div 4 = 2.25

gallons per hour.

The unit rate must be in gallons per hour, so the time must first be converted from minutes to hours by dividing by

60

.

Anahtar Kavram

Calculating unit rates by ensuring equivalent units of measure before dividing the quantity by the time.

Soru 370Soru →

Match each vehicle trip scenario to the total number of gallons of fuel required to complete the journey.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

The scout vehicle requires 5 gallons, the transport truck requires 12 gallons, the command SUV requires 16 gallons, and the hybrid commuter car requires 7 gallons.

The correct pairings are found by properly applying the formula: Gallons Consumed = Total Distance ÷ Fuel Efficiency (MPG). Performing this calculation for each scenario accurately identifies the fuel requirement.

Adım Adım Çözüm

1

Calculate the fuel required for the scout vehicle.

150 / 30 = 5 gallons.

Dividing the total travel distance by the vehicle's fuel efficiency (MPG) determines the total fuel consumed.

2

Calculate the fuel required for the transport truck.

240 / 20 = 12 gallons.

Dividing the total travel distance by the vehicle's fuel efficiency (MPG) determines the total fuel consumed.

3

Calculate the fuel required for the command SUV.

400 / 25 = 16 gallons.

Dividing the total travel distance by the vehicle's fuel efficiency (MPG) determines the total fuel consumed.

4

Calculate the fuel required for the hybrid commuter car.

350 / 50 = 7 gallons.

Dividing the total travel distance by the vehicle's fuel efficiency (MPG) determines the total fuel consumed.

Anahtar Kavram

Calculating total fuel consumption given total travel distance and fuel efficiency.

Soru 371Soru →

Translate the following geometric relationships into algebraic equations and perform the first step of simplification. Pair each geometric description on the left with its corresponding simplified equation on the right.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Match the complementary angles with

3x = 60

; the supplementary angles with

3x = 150

; the vertical angles with

x = 10

; and the adjacent angles on a straight line with

5x = 150

.

Each geometric term dictates a specific mathematical equality: 'complement' means the sum is

90^\circ

, 'supplement' and 'straight line' mean the sum is

180^\circ

, and 'vertical angles' means the measures are equal to each other. Applying these definitions and performing basic algebraic simplification yields the correct matches.

Adım Adım Çözüm

1

Formulate and simplify the equation for the complementary angles.

The setup is

3x + 30 = 90

, which simplifies to

3x = 60

.

Complementary angles always add up to

90^\circ

.

2

Formulate and simplify the equation for the supplementary angles.

The setup is

3x + 30 = 180

, which simplifies to

3x = 150

.

Supplementary angles always add up to

180^\circ

.

3

Formulate and simplify the equation for the vertical angles.

The setup is

3x = 30

, which simplifies to

x = 10

.

Vertical angles (angles opposite each other at an intersection) are geometrically equal.

4

Formulate and simplify the equation for the adjacent angles on a straight line.

The setup is

3x + (2x + 30) = 180

. Combining the

x

terms gives

5x + 30 = 180

, and subtracting 30 gives

5x = 150

.

Angles that form a linear pair on a straight line must sum to

180^\circ

.

Anahtar Kavram

Translating Geometric Angle Relationships into Algebraic Equations

Soru 372Soru →

Match each geometric angle relationship with the correct calculated value of $x$ .

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Match complementary to x = 19, vertical to x = 15, linear pair to x = 18, and alternate interior to x = 20.

Each geometric relationship dictates a distinct algebraic setup. Complementary angles sum to 90, vertical angles are set equal to each other, a linear pair sums to 180, and alternate interior angles are set equal to each other. Solving these linear equations gives the matching

x

values.

Adım Adım Çözüm

1

Set up the equation for the complementary angles.

5x - 5 = 90

Complementary angles sum to

90^\circ

.

2

Solve for

x

in the complementary equation.

x = 19

Add 5 to both sides, then divide by 5.

3

Set up the equation for the vertical angles.

5x - 30 = 2x + 15

Vertical angles are congruent (equal in measure).

4

Solve for

x

in the vertical angles equation.

x = 15

Subtract 2x from both sides and add 30 to both sides, yielding 3x = 45.

5

Set up the equation for the linear pair.

8x + 36 = 180

Angles forming a linear pair are supplementary and sum to

180^\circ

.

6

Solve for

x

in the linear pair equation.

x = 18

Subtract 36 from both sides, then divide by 8.

7

Set up the equation for the alternate interior angles.

3x + 45 = 6x - 15

Alternate interior angles on parallel lines are congruent.

8

Solve for

x

in the alternate interior equation.

x = 20

Subtract 3x from both sides and add 15 to both sides, yielding 3x = 60.

Anahtar Kavram

Translating geometric angle relationships into algebraic equations to solve for unknown variables.

Soru 373Soru →

Pair the given polynomial expressions on the left with their fully factored equivalents on the right.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

The correct pairings are:

4x^2 - 25

with

(2x - 5)(2x + 5)

;

x^2 - 8x + 15

with

(x - 3)(x - 5)

;

3x^2 + 12x - 15

with

3(x + 5)(x - 1)

; and

2x^3 - 8x

with

2x(x - 2)(x + 2)

.

Each polynomial expression was broken down into its fundamental algebraic components by identifying patterns such as the difference of squares, standard trinomial factoring, and extracting the greatest common factor.

Adım Adım Çözüm

1

Analyze the first expression

4x^2 - 25

.

It factors to

(2x - 5)(2x + 5)

.

It follows the difference of squares pattern

a^2 - b^2 = (a - b)(a + b)

with

a = 2x

and

b = 5

.

2

Analyze the second expression

x^2 - 8x + 15

.

It factors to

(x - 3)(x - 5)

.

The constant term is positive and the middle coefficient is negative, so both factors must contain negative constants that multiply to

15

and add to

-8

.

3

Analyze the third expression

3x^2 + 12x - 15

.

It factors to

3(x + 5)(x - 1)

.

Factoring out the GCF of

3

gives

3(x^2 + 4x - 5)

. The resulting quadratic factors into binomials with constants

5

and

-1

.

4

Analyze the fourth expression

2x^3 - 8x

.

It factors to

2x(x - 2)(x + 2)

.

Factoring out the GCF of

2x

gives

2x(x^2 - 4)

. The expression

x^2 - 4

is a difference of squares that further factors into

(x - 2)(x + 2)

.

Anahtar Kavram

Factoring Polynomials

Tahmini Süre:2m 0s

Soru 374Soru →

Which composite figure correctly corresponds to each set of geometric components? Match each set of transparent geometric components (Sets 1-3) to its correct superimposed composite figure (Figures X-Z). Assume the base square remains stationary while the overlay square undergoes the indicated rotation before being placed exactly on top of the base square.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Set 1 matches Figure X, Set 2 matches Figure Z, and Set 3 matches Figure Y.

Each correct pairing strictly follows spatial transformation rules. By systematically tracking the starting quadrant of the circle in the overlay, applying the stated degree and direction of rotation, and laying it over the specified diagonal base, the correct composite image can be logically deduced.

Adım Adım Çözüm

1

Analyze Set 1 rotation and layering.

The top-left circle moves to the top-right. Placed over a top-left to bottom-right diagonal, this matches Figure X.

A 90-degree clockwise rotation shifts elements to the next adjacent quadrant in a clockwise direction.

2

Analyze Set 2 rotation and layering.

The top-left circle moves to the bottom-right. Placed over a bottom-left to top-right diagonal, this matches Figure Z.

A 180-degree rotation shifts elements diagonally to the completely opposite quadrant.

3

Analyze Set 3 rotation and layering.

The bottom-left circle moves to the top-left. Placed over a bottom-left to top-right diagonal, this matches Figure Y.

A 90-degree clockwise rotation shifts the bottom-left quadrant directly up to the top-left quadrant.

Anahtar Kavram

Superimposition of Shapes

Soru 375Soru →

A drafter is reviewing a set of architectural plans. Connect each described geometric condition with its correct mathematical term.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Two angles summing to

180^\circ

match with Supplementary angles; two angles summing to

90^\circ

match with Complementary angles; opposite equal angles match with Vertical angles; lines forming a right angle match with Perpendicular lines.

Each definition precisely matches the fundamental geometric axioms for angles and lines. Recognizing these definitions is essential for solving more complex geometry problems.

Adım Adım Çözüm

1

Identify the geometric term for two angles whose sum is exactly

180^\circ

.

Supplementary angles

By geometric definition, a pair of angles that add up to

180^\circ

(forming a straight line if adjacent) are supplementary.

2

Identify the geometric term for two angles whose sum is exactly

90^\circ

.

Complementary angles

By geometric definition, a pair of angles that add up to

90^\circ

(forming a right angle if adjacent) are complementary.

3

Identify the term for the opposite angles created when two lines intersect.

Vertical angles

Intersecting lines create two pairs of non-adjacent, opposite angles known as vertical angles, which are congruent.

4

Identify the term for straight lines that intersect to form a right angle.

Perpendicular lines

When lines intersect at exactly

90^\circ

, they are defined mathematically as perpendicular.

Anahtar Kavram

Basic terminology for angle relationships and line intersections

Tahmini Süre:45s

Soru 376Soru →

Match each fundamental geometric term related to a circle with its correct definition.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Radius matches with a line segment from the center to the edge; Diameter matches with a line segment passing through the center; Circumference matches with the total distance around the circle; Chord matches with a line segment connecting any two points on the circle.

Each geometric term possesses a precise mathematical definition that distinguishes its function and location within a circle. Correctly identifying these fundamental components is an essential prerequisite for performing geometric calculations such as finding area or circumference.

Adım Adım Çözüm

1

Identify the term that represents the perimeter or boundary distance of the circle.

Circumference matches with 'The total distance around the outer boundary of a circle.'

Circumference is the only term listed that measures a 1D distance around a shape rather than a straight interior line segment.

2

Differentiate between the line segments based on their relationship to the circle's center point.

Radius connects the center to the edge. Diameter passes all the way through the center from edge to edge.

This establishes the mathematical relationship where the diameter is exactly twice the length of the radius.

3

Determine the general term for a line segment connecting any two points on the circle's edge.

Chord matches with 'A line segment whose endpoints lie on the circle, but which does not necessarily pass through the center.'

A diameter is a special type of chord, but 'chord' is the broader category that does not require passing through the center.

Anahtar Kavram

Fundamental vocabulary and structural properties of circles.

Soru 377Soru →

An engineer is evaluating the specifications of a circular pipe and recording various measurements. Match each measurement description with the correct geometric term.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

The boundary length matches to Circumference, the center-to-edge measurement to Radius, the edge-to-edge measurement through the center to Diameter, and the enclosed space to Area.

Each practical measurement perfectly aligns with a fundamental geometric property of a circle. The continuous outer boundary corresponds to the circumference. The distance from the center point to the edge is the radius. The line segment completely crossing the circle through its center is the diameter. Finally, the total two-dimensional region contained inside is the area.

Adım Adım Çözüm

1

Analyze the description for the boundary of the circular pipe.

Matches with Circumference.

By definition, the perimeter or outer boundary of a circle is called its circumference.

2

Analyze the description for the measurement from the center to the outer edge.

Matches with Radius.

The radius is the line segment connecting the center point to any point on the outer edge of the circle.

3

Analyze the description for the full width passing through the center.

Matches with Diameter.

The diameter is the longest chord of a circle, spanning from one edge to the other directly through the center.

4

Analyze the description for the enclosed two-dimensional space.

Matches with Area.

Area is the mathematical term for the amount of surface space enclosed by a two-dimensional shape.

Anahtar Kavram

Basic terminology and properties of circles

Soru 378Soru →

Match each circular geometry scenario with its corresponding simplified algebraic expression.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

The correct pairings connect each geometric scenario to its simplified algebraic derivation by applying circle formulas, expanding binomials, and rationalizing denominators.

Each expression is correctly derived by applying the fundamental formulas for circle area and circumference, followed by rigorous algebraic simplification such as factoring, binomial expansion, or radical rationalization.

Adım Adım Çözüm

1

Analyze the annular pathway area scenario.

\pi x(2r + x)

Requires subtracting the inner pool area from the total outer area and expanding the squared binomial

(r+x)^2

.

2

Determine the semicircular perimeter expression.

r(\pi + 2)

Requires adding the semicircular arc length to the straight diameter base and factoring out the radius.

3

Calculate the algebraic expression for tire revolutions.

\frac{D}{\pi d}

Requires dividing the total linear distance by the circumference of the tire, utilizing the diameter.

4

Solve for the half-area radius.

\frac{R\sqrt{2}}{2}

Requires setting up an area ratio equation, solving for the new radius, and rationalizing the denominator of the resulting square root.

Anahtar Kavram

Algebraic representation and derivation of advanced circular measurements

Soru 379Soru →

A recruiting station commander records the number of new applicants processed each day for $5$ consecutive days. The daily counts are $3$ , $3$ , $5$ , $8$ , and $11$ . Match each measure of central tendency to its correct calculated value for this data set.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

The correct matches are: Mode pairs with

3

, Median pairs with

5

, and Mean pairs with

6

.

Based on the data set of

3, 3, 5, 8, 11

, the mode is

3

because it appears most frequently. The median is

5

because it is the central value of the ordered list. The mean is

6

because the sum (

30

) divided by the count (

5

) equals

6

.

Adım Adım Çözüm

1

Determine the mode of the data set.

Mode =

3

The mode is the number that appears most frequently.

3

is the only number that appears more than once.

2

Determine the median of the data set.

Median =

5

The data is already arranged in ascending order:

3, 3, 5, 8, 11

. The middle number (third position out of five) is

5

.

3

Calculate the mean of the data set.

Mean =

6

Calculate the sum of the numbers (

3 + 3 + 5 + 8 + 11 = 30

) and divide by the number of days (

5

):

30 \div 5 = 6

.

Anahtar Kavram

Calculating the primary measures of central tendency (mean, median, and mode) for a data set.

Tahmini Süre:45s

Soru 380Soru →

Match each electrical measurement scenario with the correct digital multimeter (DMM) lead placement, selector dial setting, and circuit connection method.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Each measurement scenario correctly aligns with its unique combination of meter jack, dial mode, and circuit connection:

12\text{ V}

DC lamp voltage drop matches parallel connection using

\text{V/}\Omega

and

\text{COM}

on

\text{DCV}

;

450\text{ mA}

relay current matches series connection using

\text{mA/}\mu\text{A}

and

\text{COM}

on

\text{DCA}

;

8.2\text{ A}

fan current matches series connection using the

10\text{ A}

jack and

\text{COM}

on

\text{DCA}

;

120\text{ V}

AC outlet voltage matches parallel connection using

\text{V/}\Omega

and

\text{COM}

on

\text{ACV}

.

The correct pairings enforce all foundational meter rules: voltage is measured across a component in parallel using the volt/ohm jack in the appropriate DC or AC dial mode, while current is measured inline in series using the appropriate current jack (milliamp jack for fractions of an amp, and the 10A terminal for high currents) to protect internal fuses and ensure accurate readings.

Adım Adım Çözüm

1

Differentiate between voltage and current measurement connection rules.

Voltmeters must always be connected in parallel across components without opening the circuit, whereas ammeters must always be connected in series by breaking the circuit line.

Voltmeters possess extremely high internal impedance to prevent loading the circuit, while ammeters possess near-zero internal impedance to allow current to pass through.

2

Distinguish between direct current (DC) and alternating current (AC) dial configurations.

Automotive DC systems and DC relay lines require the DCV and DCA functions, while standard utility electrical wall receptacles supply sinusoidal alternating voltage requiring the ACV function.

Selecting the incorrect waveform mode causes inaccurate readings, meter errors, or failure to register potential.

3

Determine the proper current input jack based on expected current magnitude.

Low current (

450\text{ mA}

) is safely routed through the standard fused milliamp/microamp (mA/

\mu

A) jack, whereas high current (

8.2\text{ A}

) must be routed through the dedicated

10\text{ A}

high-current terminal.

Placing currents above

200\text{--}500\text{ mA}

into the milliamp jack will instantly blow the internal meter fuse.

Anahtar Kavram

Digital Multimeter Voltage and Current Configuration

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram