Tüm alıştırma soruları

Complete the statement regarding the fundamental electrical behavior of a series circuit.

Aşağıdaki boşlukları doldurun

In a series circuit, because all electrical components are connected end-to-end in a single continuous path, the electric is the same at every point throughout the circuit.

Cevabı ve açıklamayı göster

Cevap

current (or amperage)

In any series circuit, electrical components share a single continuous conductive loop. Under the principle of conservation of electric charge, the rate at which charge passes through any cross-section of the conductor (current) must be identical at all points (

I_{\text{total}} = I_1 = I_2

).

Adım Adım Çözüm

1

Analyze the structural path of a series circuit.

A series circuit consists of a single closed loop with no branch points or alternate paths.

By definition, components in series are connected sequentially in one continuous line.

2

Apply the law of conservation of charge to determine which parameter remains constant across all components.

The rate of electron flow must be equal across all parts of the circuit (

I_{\text{total}} = I_1 = I_2 = \dots

).

Because charge cannot accumulate or disappear at any junction in a single loop, current is uniform everywhere.

Anahtar Kavram

Electric current is identical at all points in a series circuit because there is only one pathway for charge to flow.

Tahmini Süre:30s

Soru 562Soru →

An electronics technician is analyzing an NPN bipolar junction transistor (BJT) configured as an amplifier in a common-emitter circuit. For the transistor to operate properly in its linear active region, which combination of internal junction biasing conditions must be established?

Forward-biasing both the base-emitter junction and the collector-base junction

Forward-biasing the base-emitter junction and reverse-biasing the collector-base junction

Reverse-biasing the base-emitter junction and forward-biasing the collector-base junction

Reverse-biasing both the base-emitter junction and the collector-base junction

Cevabı ve açıklamayı göster

Cevap: Forward-biasing the base-emitter junction and reverse-biasing the collector-base junction

Cevap

Forward-biasing the base-emitter junction and reverse-biasing the collector-base junction

For any bipolar junction transistor (BJT) to function as a linear amplifier in the active region, the input base-emitter PN junction must be forward-biased to permit carrier injection, and the output collector-base PN junction must be reverse-biased to attract and collect these carriers across the junction.

Adım Adım Çözüm

1

Identify the operational requirement for linear amplification in a BJT

Linear amplification requires the transistor to operate strictly in the active mode.

Operating outside the active region causes either signal clipping in saturation or complete signal cutoff.

2

Determine the required bias across the base-emitter (input) junction

The base-emitter junction must be forward-biased (positive base relative to emitter in an NPN transistor).

Forward bias reduces the potential barrier across the base-emitter junction, allowing majority carriers (electrons) to be injected from the emitter into the thin base layer.

3

Determine the required bias across the collector-base (output) junction

The collector-base junction must be reverse-biased (positive collector relative to base in an NPN transistor).

Reverse bias widens the collector-base depletion region and sets up a strong electric field that collects the injected electrons passing through the base into the collector.

Anahtar Kavram

BJT Active Region Biasing Conditions

Tahmini Süre:1m 15s

Soru 563Soru →

In an electronics schematic, a bipolar junction transistor (BJT) symbol features an arrow on the emitter lead pointing outward, away from the base. Which type of transistor is represented by this symbol?

PNP transistor

NPN transistor

Junction field-effect transistor (JFET)

Zener diode

Cevabı ve açıklamayı göster

Cevap: NPN transistor

Cevap

An NPN transistor is represented by a BJT schematic symbol where the emitter arrow points outward, away from the base.

In electronics schematic diagrams, the arrow on the emitter terminal indicates the direction of conventional current flow. For an NPN transistor, this arrow points outward (away from the base). A common memory aid is 'NPN = Not Pointing iN'.

Adım Adım Çözüm

1

Identify the component family and terminal structure.

The component is a Bipolar Junction Transistor (BJT) with three terminals: Collector, Base, and Emitter.

Recognizing the core three-terminal configuration establishes the category of semiconductor device.

2

Analyze the direction of the arrow located on the emitter terminal.

The arrow points outward (away from the base terminal).

In standard schematic conventions, the arrow on the emitter indicates the direction of conventional current flow during forward bias.

3

Match the arrow direction to the correct transistor polarity type.

An outward-pointing arrow corresponds to an NPN transistor ('Not Pointing iN'), whereas an inward-pointing arrow corresponds to a PNP transistor ('Pointing iN Proudly').

Differentiating between NPN and PNP configurations is essential for determining circuit polarity and proper biasing.

Anahtar Kavram

BJT schematic symbols use an arrow on the emitter terminal to distinguish between NPN (arrow pointing out) and PNP (arrow pointing in) configurations.

Tahmini Süre:45s

Soru 564Soru →

A technician needs to operate a $120\text{ V}$ alternating current (AC) power tool using a $12\text{ V}$ direct current (DC) vehicle battery as the power source. Which sequence of components is required to operate this equipment?

A step-up transformer connected directly to the battery, followed by a rectifier to alternate polarity

An inverter to convert the DC supply into AC, combined with a transformer to increase the voltage

A rectifier bridge to produce an alternating waveform, followed by a series diode to prevent reverse flow

A voltage divider to convert DC voltage into current flow before boosting frequency with an inductor

Cevabı ve açıklamayı göster

Cevap: An inverter to convert the DC supply into AC, combined with a transformer to increase the voltage

Cevap

An inverter to convert the DC supply into AC, combined with a transformer to increase the voltage

A battery supplies unidirectional direct current (DC). Because standard transformers require alternating current (AC) to induce voltage across their windings, the DC must first be converted into AC using an inverter circuit, which can then be stepped up to the required

120\text{ V}

AC level.

Adım Adım Çözüm

1

Identify the power characteristics of the source and the load

The source provides

12\text{ V}

steady direct current (DC), whereas the load requires

120\text{ V}

alternating current (AC).

Direct current flows continuously in one direction at constant polarity, while alternating current periodically reverses direction.

2

Determine the required electrical conversion and voltage transformation

DC must be converted to AC via an electronic inverter circuit, and the voltage magnitude must be increased tenfold.

Transformers operate on mutual induction created by varying magnetic fields, meaning voltage can only be stepped up or down efficiently after conversion to AC.

Anahtar Kavram

Direct Current (DC) maintains unidirectional flow while Alternating Current (AC) reverses direction periodically; conversion from DC to AC requires an inverter.

Tahmini Süre:45s

Soru 565Soru →

An automotive technician connects a diagnostic scanner to a standard 12-volt car battery. Which statement correctly describes the current supplied by this direct current (DC) power source?

The direction of electron flow periodically reverses at regular intervals.

Electrons flow continuously in only one constant direction through the circuit.

The voltage must continuously oscillate between positive and negative values to deliver power.

Electrons remain stationary while electromotive force alone travels through the conductor.

Cevabı ve açıklamayı göster

Cevap: Electrons flow continuously in only one constant direction through the circuit.

Cevap

Electrons flow continuously in only one constant direction through the circuit.

A battery produces direct current (DC), which is characterized by the continuous flow of electrons in a single, unchanging direction through a closed electrical circuit.

Adım Adım Çözüm

1

Identify the electrical power source and current type.

A 12-volt vehicle battery is an electrochemical source supplying direct current (DC).

Establishing the power source defines the behavior of current flow in the circuit.

2

Apply the fundamental definition of direct current (DC).

Direct current flows in a single, constant direction from the negative terminal to the positive terminal through the external circuit.

Unlike alternating current, direct current maintains a steady polarity and does not alternate direction.

Anahtar Kavram

Direct current (DC) is the unidirectional flow of electric charge, maintaining a constant direction of electron movement over time.

Tahmini Süre:30s

Soru 566Soru →

In a bipolar junction transistor (BJT) used in a common-emitter circuit, which terminal receives the small control current required to regulate the larger current flowing between the other two terminals?

Collector

Base

Emitter

Gate

Cevabı ve açıklamayı göster

Cevap: Base

Cevap

The base terminal receives the small control current that regulates current flow between the collector and emitter.

In a bipolar junction transistor (BJT), the base is the central control terminal. A small current entering the base allows a significantly larger current to conduct between the collector and emitter, functioning as an amplifier or an electronic switch.

Adım Adım Çözüm

1

Identify the terminal architecture of a bipolar junction transistor (BJT)

A standard BJT has three functional leads: the Base, the Collector, and the Emitter.

Establishes the available terminal functions specific to current-driven bipolar transistors.

2

Determine the control mechanism in a common-emitter configuration

Applying a small base current (

I_B

) modulates a larger collector current (

I_C

) according to the transistor gain (

\beta

), yielding

I_C = \beta \times I_B

.

Identifies the base as the designated input control lead in BJT switching and amplification circuits.

Anahtar Kavram

BJT Terminal Roles and Current Control

Tahmini Süre:45s

Soru 567Soru →

A technician connects a $12\text{ V}$ direct current (DC) battery directly across the primary winding of a $1:10$ step-up transformer expecting a steady $120\text{ V}$ output. Instead, the secondary winding produces only a brief momentary pulse at connection, followed by $0\text{ V}$ . Which statement best explains this outcome?

The transformer converts direct current into alternating current at a frequency too high for standard measurement.

A steady direct current creates a static magnetic field, which fails to produce the changing magnetic flux required for continuous induction.

Direct current causes the iron core to act as a reverse-biased diode, blocking all electrical transfer.

The unidirectional flow of electrons in direct current cancels out the electromotive force across the secondary terminals.

Cevabı ve açıklamayı göster

Cevap: A steady direct current creates a static magnetic field, which fails to produce the changing magnetic flux required for continuous induction.

Cevap

A steady direct current creates a static magnetic field, which fails to produce the changing magnetic flux required for continuous induction.

Transformers operate on mutual electromagnetic induction, which requires a continuously changing magnetic field. Alternating current (AC) naturally provides this because its magnitude and polarity oscillate continuously. When steady direct current (DC) is applied, a brief pulse occurs only while current ramps up during connection; once steady state is reached, the magnetic field is static, resulting in zero rate of change of magnetic flux and zero induced secondary voltage.

Adım Adım Çözüm

1

Analyze the nature of the power source (DC).

Direct current maintains a constant magnitude and unidirectional flow after reaching steady state.

Understanding the source characteristic is essential to determine its magnetic effect in the primary winding.

2

Evaluate the magnetic field produced by steady direct current in the transformer core.

A constant direct current establishes a stationary, unchanging magnetic field (

\frac{d\Phi}{dt} = 0

).

A changing current is necessary to produce an expanding or collapsing magnetic field.

3

Apply Faraday's Law of Electromagnetic Induction to the secondary winding.

Induced secondary voltage is proportional to the rate of change of magnetic flux (

V_{\text{sec}} = -N \frac{d\Phi}{dt} = 0\text{ V}

).

Because flux is static once DC is fully established, no continuous voltage can be induced across the secondary coil.

Anahtar Kavram

Direct Current (DC) vs. Alternating Current (AC) in Transformer Operation

Tahmini Süre:45s

Soru 568Soru →

A $24\text{ V}$ direct current (DC) power supply is connected to a circuit with two resistors in series: a $4\ \Omega$ resistor and an $8\ \Omega$ resistor. What is the current flowing through the $8\ \Omega$ resistor?

3\text{ A}

2\text{ A}

6\text{ A}

9\text{ A}

Cevabı ve açıklamayı göster

Cevap: $2\text{ A}$

Cevap

2\text{ A}

The total resistance of the series circuit is the direct sum of the resistors (

4\ \Omega + 8\ \Omega = 12\ \Omega

). According to Ohm's Law (

I = V / R

), dividing the

24\text{ V}

source by

12\ \Omega

yields a total current of

2\text{ A}

. Because a series circuit provides only a single continuous path for electron flow, the current is identical through every component in the loop, meaning

2\text{ A}

flows through the

8\ \Omega

resistor.

Adım Adım Çözüm

1

Calculate the total equivalent resistance of the series circuit.

R_{\text{total}} = R_1 + R_2 = 4\ \Omega + 8\ \Omega = 12\ \Omega

In any series circuit, individual resistances add directly together to form the total circuit resistance.

2

Apply Ohm's Law to determine the total circuit current.

I_{\text{total}} = \frac{V_{\text{total}}}{R_{\text{total}}} = \frac{24\text{ V}}{12\ \Omega} = 2\text{ A}

Current equals total voltage divided by total resistance.

3

Determine the current flowing specifically through the

8\ \Omega

resistor.

I_{R2} = I_{\text{total}} = 2\text{ A}

In a single-loop series circuit, current is uniform at all points and through all components.

Anahtar Kavram

Series Circuit Current and Total Resistance

Tahmini Süre:45s

Soru 569Soru →

A high-voltage direct current power supply delivers an electromotive force (EMF) of $2.4\text{ kV}$ across a circuit load. Which of the following correctly expresses this potential difference in standard volts and describes its fundamental role in the circuit?

2.4\text{ V}

, which provides the electrical pressure to push current through the load

2{}400\text{ V}

, which provides the electrical pressure to push current through the load

2{}400\text{ A}

, which measures the rate of charge flow through the load

240\text{ V}

, which measures the alternating frequency of the electrical source

Cevabı ve açıklamayı göster

Cevap: $2{}400\text{ V}$ , which provides the electrical pressure to push current through the load

Cevap

2{}400\text{ V}

, which provides the electrical pressure to push current through the load

The correct response accurately applies the metric prefix multiplier for kilo- (

1\text{ kV} = 1{}000\text{ V}

) to compute

2.4 \times 1{}000 = 2{}400\text{ V}

, and correctly identifies electromotive force (EMF) as the electrical potential difference or pressure that drives electron flow through the circuit.

Adım Adım Çözüm

1

Convert the electromotive force from kilovolts (

\text{kV}

) to standard volts (

\text{V}

)

2.4\text{ kV} \times 1{}000\text{ V/kV} = 2{}400\text{ V}

The metric prefix kilo- represents a factor of

10^3

(

1{}000

units).

2

Identify the physical role and unit of Electromotive Force (EMF)

EMF is the potential difference or electrical pressure that causes electrons to flow through a circuit, measured in volts (

\text{V}

)

Voltage/EMF is the driving force behind current, distinctly separate from current itself which is the rate of electron flow measured in amperes (

\text{A}

).

Anahtar Kavram

Electromotive force (EMF) is the potential difference (measured in volts) that provides the electrical pressure to drive charge through a closed circuit, where

1\text{ kV} = 1{}000\text{ V}

.

Tahmini Süre:1m 0s

Soru 570Soru →

A circuit in a timing module contains two $30\text{ }\mu\text{F}$ capacitors connected in parallel. This parallel pair is then connected in series with a third $15\text{ }\mu\text{F}$ capacitor. What is the total equivalent capacitance of this network?

75\text{ }\mu\text{F}

12\text{ }\mu\text{F}

30\text{ }\mu\text{F}

0.012\text{ }\mu\text{F}

Cevabı ve açıklamayı göster

Cevap: $12\text{ }\mu\text{F}$

Cevap

The total equivalent capacitance of the network is

12\text{ }\mu\text{F}

.

For capacitors in parallel, the total capacitance is the sum of the individual values:

30\text{ }\mu\text{F} + 30\text{ }\mu\text{F} = 60\text{ }\mu\text{F}

. When this

60\text{ }\mu\text{F}

equivalent combination is connected in series with a

15\text{ }\mu\text{F}

capacitor, the product-over-sum rule is applied:

(60 \times 15) / (60 + 15) = 900 / 75 = 12\text{ }\mu\text{F}

.

Adım Adım Çözüm

1

Calculate the equivalent capacitance of the two parallel capacitors (

C_1 = 30\text{ }\mu\text{F}

and

C_2 = 30\text{ }\mu\text{F}

).

C_p = C_1 + C_2 = 30\text{ }\mu\text{F} + 30\text{ }\mu\text{F} = 60\text{ }\mu\text{F}

Capacitors in parallel add their plate surface areas together, so their capacitances add directly.

2

Calculate the total capacitance when

C_p = 60\text{ }\mu\text{F}

is placed in series with

C_3 = 15\text{ }\mu\text{F}

.

C_{\text{total}} = \frac{C_p \times C_3}{C_p + C_3} = \frac{60 \times 15}{60 + 15} = \frac{900}{75} = 12\text{ }\mu\text{F}

Capacitors in series combine inversely using the reciprocal formula, identical to the formula used for parallel resistors.

Anahtar Kavram

Equivalent Capacitance in Series-Parallel Combinations

Tahmini Süre:1m 15s

Soru 571Soru →

An electronics technician needs to remove excess solder from a circuit board contact using a manual spring-loaded desoldering pump (solder sucker). Arrange the procedural steps in the correct sequence from first to last.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence is: prime the plunger into the locked position, melt the solder with the iron tip, place the nozzle directly over the molten pool, and trigger the release button to vacuum the solder.

A manual desoldering pump relies on rapid vacuum suction. The tool must be pre-cocked before thermal application. Once the iron melts the joint, the nozzle is placed adjacent to the iron tip over the liquid pool, and the release button is pressed immediately to extract the molten alloy before it solidifies.

Adım Adım Çözüm

1

Cock the desoldering pump plunger.

The internal spring is compressed and latched, preparing the chamber for rapid suction.

Once solder is melted, time is critical; the tool must be primed before heating the workpiece.

2

Place the soldering iron tip against the joint.

Thermal energy transfers into the old joint, bringing the solder above its melting point.

Solder must be completely liquid to flow freely into the desoldering tool.

3

Bring the pump nozzle to the molten joint.

The nozzle forms a close seal over the molten solder puddle.

Proper nozzle placement ensures maximum suction efficiency without cooling the joint prematurely.

4

Trigger the release button.

The spring releases, pulling a rapid vacuum that draws the liquid solder inside the barrel.

Immediate suction captures the solder while it remains at liquid temperature.

Anahtar Kavram

Operating procedure for vacuum desoldering tools in electronics maintenance.

Tahmini Süre:45s

Soru 572Soru →

An electronics technician is repairing a power supply filter network. The circuit requires replacing a section containing two $12\text{ }\mu\text{F}$ capacitors connected in series, which are arranged in parallel with a single $6\text{ }\mu\text{F}$ capacitor. What is the total equivalent capacitance of this entire combination?

4.8\text{ }\mu\text{F}

12\text{ }\mu\text{F}

30\text{ }\mu\text{F}

12\text{ nF}

Cevabı ve açıklamayı göster

Cevap: $12\text{ }\mu\text{F}$

Cevap

The total equivalent capacitance of the network is

12\text{ }\mu\text{F}

.

To find the total equivalent capacitance, solve the series combination first: two

12\text{ }\mu\text{F}

capacitors in series provide an equivalent capacitance of

\frac{12 \times 12}{12 + 12} = 6\text{ }\mu\text{F}

. Next, add the parallel branch value directly:

6\text{ }\mu\text{F} + 6\text{ }\mu\text{F} = 12\text{ }\mu\text{F}

.

Adım Adım Çözüm

1

Calculate the equivalent capacitance of the two series-connected capacitors.

C_{\text{series}} = 6\text{ }\mu\text{F}

Capacitors in series combine reciprocally using the formula

C_{\text{series}} = \frac{C_1 \times C_2}{C_1 + C_2} = \frac{12 \times 12}{12 + 12} = \frac{144}{24} = 6\text{ }\mu\text{F}

.

2

Add the equivalent series capacitance to the parallel capacitor.

C_{\text{total}} = 12\text{ }\mu\text{F}

Capacitors in parallel add directly together:

C_{\text{total}} = C_{\text{series}} + C_3 = 6\text{ }\mu\text{F} + 6\text{ }\mu\text{F} = 12\text{ }\mu\text{F}

.

Anahtar Kavram

Capacitors in series combine reciprocally (reducing total capacitance), whereas capacitors in parallel add directly together (increasing total capacitance).

Alternatif Yöntem

Since the two series capacitors are identical, their equivalent capacitance is simply half of one capacitor's value:

\frac{12\text{ }\mu\text{F}}{2} = 6\text{ }\mu\text{F}

. Adding the identical

6\text{ }\mu\text{F}

parallel branch doubles this value back to

12\text{ }\mu\text{F}

.

Tahmini Süre:1m 30s

Soru 573Soru →

An aircraft instrumentation circuit incorporates a $24\text{ V}$ primary DC power source connected in series-aiding polarity with a $750\text{ mV}$ reference cell. If a $1.75\text{ V}$ auxiliary bias source is wired into the same series branch in series-opposing polarity, what is the net electromotive force (EMF) measured across the output terminals?

26.5\text{ V}

23.0\text{ V}

772.25\text{ V}

23.0\text{ A}

Cevabı ve açıklamayı göster

Cevap: $23.0\text{ V}$

Cevap

The net electromotive force across the terminals is

23.0\text{ V}

.

The correct answer is obtained by converting

750\text{ mV}

to

0.75\text{ V}

, summing the aiding sources (

24\text{ V} + 0.75\text{ V} = 24.75\text{ V}

), and subtracting the opposing

1.75\text{ V}

source, resulting in a net electromotive force of

23.0\text{ V}

.

Adım Adım Çözüm

1

Convert the reference cell rating from millivolts to volts

750\text{ mV} = 750 \times 10^{-3}\text{ V} = 0.75\text{ V}

All voltage values in a series combination must be expressed in the same unit before performing arithmetic operations.

2

Combine the series-aiding electromotive forces

V_{\text{aiding}} = 24\text{ V} + 0.75\text{ V} = 24.75\text{ V}

Voltage sources connected in series-aiding polarity reinforce one another, so their potentials add directly.

3

Subtract the series-opposing bias source to find the net EMF

\text{EMF}_{\text{net}} = 24.75\text{ V} - 1.75\text{ V} = 23.0\text{ V}

A source wired in opposing polarity establishes a potential in the reverse direction, reducing the overall electromotive force.

Anahtar Kavram

Series electromotive force calculation involving aiding/opposing polarities and metric prefix conversion

Tahmini Süre:1m 15s

Soru 574Soru →

In a direct current (DC) circuit, electrical current periodically reverses its direction of flow at a fixed frequency measured in hertz ( $\text{Hz}$ ).

Doğru

Yanlış

Cevabı ve açıklamayı göster

Cevap: False

Cevap

False. Direct current (DC) flows in a single constant direction, while alternating current (AC) periodically reverses its direction of flow.

The statement is false because direct current (DC) flows in one fixed direction without reversing. The periodic reversal of direction and polarity over time at a frequency measured in hertz (

\text{Hz}

) is the defining attribute of alternating current (AC).

Adım Adım Çözüm

1

Define the fundamental behavior of direct current (DC).

Direct current is characterized by the unidirectional flow of electric charge, maintaining a constant polarity with a frequency of

0\text{ Hz}

.

Establishing the baseline definition of DC.

2

Analyze the characteristic described in the statement.

Periodic reversal of current flow at a measurable frequency in hertz (

\text{Hz}

) defines alternating current (AC).

Distinguishing between AC and DC waveform characteristics.

3

Evaluate the accuracy of the statement.

The statement incorrectly assigns the periodic reversal and frequency properties of AC to DC, making the statement false.

Determining the correct truth value.

Anahtar Kavram

Direct Current (DC) flows continuously in one direction with zero frequency, whereas Alternating Current (AC) periodically reverses direction at a specified frequency.

Tahmini Süre:30s

Soru 575Soru →

An electrical current whose magnitude periodically fluctuates over time without ever reversing its polarity or direction of electron flow is classified as an alternating current (AC).

Doğru

Yanlış

Cevabı ve açıklamayı göster

Cevap: False

Cevap

False

The statement is false because the defining characteristic of alternating current (AC) is a periodic reversal in the direction of current flow and voltage polarity. Current that varies in magnitude while remaining strictly unidirectional is pulsating direct current (DC).

Adım Adım Çözüm

1

Analyze the fundamental definition of alternating current (AC).

Alternating current requires that electrons periodically change direction, moving back and forth across a zero reference axis.

AC is defined by periodic reversal of polarity and current direction, not merely changing magnitude.

2

Analyze the characteristics of direct current (DC) and its variations.

Direct current is any current that flows continuously in a single direction; when its amplitude varies over time without crossing zero to reverse direction, it is termed pulsating DC.

Unidirectional current flow remains DC regardless of whether the magnitude is constant or time-varying.

3

Evaluate the statement based on electrical classification principles.

The statement incorrectly classifies a unidirectional pulsating current as alternating current.

Because polarity never reverses, the current is DC, making the statement false.

Anahtar Kavram

Classification of DC vs. AC based on polarity reversal versus magnitude variation

Soru 576Soru →

A technician connects a $10\text{ }\mu\text{F}$ capacitor in parallel with a $22\text{ }\mu\text{F}$ capacitor in a power supply filter circuit. What is the total equivalent capacitance of this combination in microfarads ( $\mu\text{F}$ )?

Cevabı ve açıklamayı göster

Cevap: 32

Cevap

32 uF

When capacitors are connected in parallel, their total capacitance is the direct sum of the individual capacitances:

C_{\text{total}} = C_1 + C_2

. Adding

10\text{ }\mu\text{F}

and

22\text{ }\mu\text{F}

results in a total equivalent capacitance of

32\text{ }\mu\text{F}

.

Adım Adım Çözüm

1

Identify the circuit configuration and the relevant formula for equivalent capacitance.

The two capacitors are connected in parallel, meaning their total capacitance is the sum of their individual capacitances:

C_{\text{total}} = C_1 + C_2

.

Connecting capacitors in parallel effectively increases the total plate surface area, allowing more electric charge to be stored at a given voltage.

2

Calculate the sum of the individual capacitances.

C_{\text{total}} = 10\text{ }\mu\text{F} + 22\text{ }\mu\text{F} = 32\text{ }\mu\text{F}

.

Direct addition yields the total equivalent capacitance.

Anahtar Kavram

Total capacitance in a parallel circuit is calculated by directly adding the individual capacitances (

C_{\text{total}} = C_1 + C_2 + \dots

).

Tahmini Süre:45s

Soru 577Soru →

A portable two-way radio is powered by four $1.5\text{ V}$ battery cells connected in series aiding. What is the total electromotive force (EMF) supplied to the radio circuit, in volts?

Cevabı ve açıklamayı göster

Cevap: 6

Cevap

The total electromotive force supplied is

6.0\text{ V}

(or

6\text{ V}

).

Connecting direct current (DC) cells in series aiding connects the positive terminal of each cell to the negative terminal of the next, causing their individual potential differences to combine additively. Therefore, four

1.5\text{ V}

cells produce a total EMF of

4 \times 1.5\text{ V} = 6.0\text{ V}

.

Adım Adım Çözüm

1

Apply the series voltage addition principle

V_{\text{total}} = V_1 + V_2 + V_3 + V_4

When voltage sources are connected in series aiding, their individual potential differences add together directly to provide the total electromotive force.

2

Perform the calculation for four identical

1.5\text{ V}

cells

V_{\text{total}} = 4 \times 1.5\text{ V} = 6.0\text{ V}

Multiplying the single-cell potential by the quantity of series-connected cells yields the overall circuit EMF.

Anahtar Kavram

Series Voltage Addition and Electromotive Force (EMF)

Tahmini Süre:45s

Soru 578Soru →

Passage:
Commercial aircraft hydraulic reservoirs are continuously pressurized with regulated bleed air tapped from the engine compressors. At cruising altitudes exceeding 30,000 feet, ambient atmospheric pressure drops significantly, which reduces the absolute pressure within unsealed fluid containers. Without positive internal air pressure in the reservoir, the engine-driven hydraulic pumps would experience cavitation—the formation and sudden collapse of vapor bubbles—leading to erratic flight control response and rapid pump degradation.

Based on the passage, which of the following is implied regarding high-altitude flight and hydraulic systems?

Engine compressors must avoid supplying bleed air to the reservoir to keep flight controls stable.

Lower ambient atmospheric pressure at cruising altitude increases the tendency of hydraulic fluid to vaporize.

Commercial aircraft are restricted from cruising above 30,000 feet due to unavoidable pump failure.

Cavitation occurs when excess air pressure from the compressor forces bubbles into the fluid lines.

Cevabı ve açıklamayı göster

Cevap: Lower ambient atmospheric pressure at cruising altitude increases the tendency of hydraulic fluid to vaporize.

Cevap

Lower ambient atmospheric pressure at cruising altitude increases the tendency of hydraulic fluid to vaporize.

The correct answer accurately synthesizes the text clues: high altitude reduces ambient pressure, which would cause fluid vaporization (cavitation) unless actively counteracted by artificial pressurization. Thus, lower ambient pressure increases the fluid's tendency to vaporize.

Adım Adım Çözüm

1

Identify the cause-and-effect relationship in the text.

The passage notes that at high altitudes, lower ambient atmospheric pressure reduces container pressure, leading to cavitation (vapor bubbles) unless positive air pressure is applied.

Understanding the interaction between ambient pressure and fluid behavior is essential to identify what is unstated but logically necessary.

2

Deduce the unstated physical implication.

Since artificial pressurization is required to stop vapor bubbles from forming under low ambient pressure, lower atmospheric pressure inherently facilitates the vaporization of the fluid.

An implied meaning is a valid deduction directly supported by the passage facts without introducing unsupported assumptions.

3

Evaluate the answer choices against the deduced implication.

The choice stating that lower ambient atmospheric pressure increases the tendency of hydraulic fluid to vaporize accurately captures this implied concept.

This choice matches the text logic while avoiding verbatim traps or extreme overextensions.

Anahtar Kavram

Identifying Implied Meanings

Tahmini Süre:1m 0s

Soru 579Soru →

Which of the following represents the solution set for the inequality below?

-3(x - 2) + 5x > 6x - 10

x < 4

x > 4

x < 1

x > 2

Cevabı ve açıklamayı göster

Cevap: $x < 4$

Cevap

The correct answer is

x < 4

.

The correct solution is achieved by properly expanding the expression, isolating the variable

x

, and correctly reversing the inequality symbol when dividing both sides by a negative number (

-4

).

Adım Adım Çözüm

1

Distribute the

-3

into the parentheses.

-3x + 6 + 5x > 6x - 10

Expanding the terms allows for the combination of like variables.

2

Combine like terms on the left side of the inequality.

2x + 6 > 6x - 10

Simplifying the expression makes it easier to isolate the variable.

3

Subtract

6x

from both sides of the inequality.

-4x + 6 > -10

This step groups all variable terms onto one side of the inequality.

4

Subtract

6

from both sides.

-4x > -16

This isolates the variable term completely.

5

Divide both sides by

-4

and reverse the inequality sign.

x < 4

Dividing or multiplying an inequality by a negative number requires flipping the inequality direction.

Anahtar Kavram

Solving one-variable inequalities requiring distribution and division by a negative coefficient.

Tahmini Süre:1m 0s

Soru 580Soru →

A transistor can use a small electrical signal at one terminal to control a much larger current flowing through its other terminals.

Doğru

Yanlış

Cevabı ve açıklamayı göster

Cevap: True

Cevap

True

The statement is true because the defining characteristic of a transistor is its ability to govern a large current path using a relatively weak electrical control signal, making it effective for both amplification and switching.

Adım Adım Çözüm

1

Identify the primary operational functions of a transistor in electronic circuits.

Transistors are solid-state components designed to act as electronic switches and signal amplifiers.

Recalling the basic definition and purpose of semiconductor devices establishes the core functional criteria.

2

Evaluate the relationship between the input control signal and the output circuit current.

Applying a relatively small signal to the control terminal modulates and directs a much larger current between the power terminals.

This control mechanism allows small electronic signals to switch heavy loads on or off and amplify weak audio or radio signals.

Anahtar Kavram

Transistor amplification and electronic switching principle

Tahmini Süre:30s

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Alternatif Yöntem

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm