Tüm alıştırma soruları

Soru 41Soru →

An electronics technician evaluates four separate direct current (DC) test circuits on a workbench. Match each circuit description on the left with its corresponding calculated electrical quantity on the right using Ohm's law ( $V = I \times R$ ).

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

The circuit drawing

12\text{ mA}

at

48\text{ V}

matches a total resistance of

4\text{ k}\Omega

; the lamp with

250\text{ }\Omega

at

40\text{ mA}

matches a voltage drop of

10\text{ V}

; the

1.5\text{ k}\Omega

resistor at

30\text{ V}

matches a current of

20\text{ mA}

; and the

80\text{ }\Omega

relay coil at

24\text{ V}

matches a current of

300\text{ mA}

.

Each circuit scenario directly applies one variation of Ohm's law after properly adjusting metric units:

R = \frac{V}{I}

gives

4\text{ k}\Omega

,

V = I \times R

gives

10\text{ V}

, and

I = \frac{V}{R}

gives

20\text{ mA}

and

300\text{ mA}

respectively.

Adım Adım Çözüm

1

Calculate resistance for the first circuit (

V = 48\text{ V}

,

I = 12\text{ mA}

)

R = \frac{48\text{ V}}{0.012\text{ A}} = 4{}000\text{ }\Omega = 4\text{ k}\Omega

Convert milliamperes to amperes (

12\text{ mA} = 0.012\text{ A}

) and apply Ohm's law formula

R = \frac{V}{I}

.

2

Calculate voltage across the lamp (

R = 250\text{ }\Omega

,

I = 40\text{ mA}

)

V = 0.040\text{ A} \times 250\text{ }\Omega = 10\text{ V}

Convert milliamperes to amperes (

40\text{ mA} = 0.040\text{ A}

) and apply

V = I \times R

.

3

Calculate current through the resistor (

V = 30\text{ V}

,

R = 1.5\text{ k}\Omega

)

I = \frac{30\text{ V}}{1{}500\text{ }\Omega} = 0.020\text{ A} = 20\text{ mA}

Convert kilohms to ohms (

1.5\text{ k}\Omega = 1{}500\text{ }\Omega

) and apply

I = \frac{V}{R}

, expressing the answer in milliamperes.

4

Calculate current through the relay coil (

V = 24\text{ V}

,

R = 80\text{ }\Omega

)

I = \frac{24\text{ V}}{80\text{ }\Omega} = 0.30\text{ A} = 300\text{ mA}

Apply

I = \frac{V}{R}

and convert amperes to milliamperes (

0.30\text{ A} = 300\text{ mA}

).

Anahtar Kavram

Ohm's law governs the fundamental mathematical relationship between electromotive force (voltage in volts), current (amperes), and opposition to current (resistance in ohms):

V = I \times R

,

I = \frac{V}{R}

, and

R = \frac{V}{I}

, with standard metric prefix conversions (

1\text{ k}\Omega = 1{}000\text{ }\Omega

,

1\text{ A} = 1{}000\text{ mA}

).

Tahmini Süre:1m 30s

Soru 42Soru →

A technician is assembling a low-pass filter circuit and connects two inductors in series with values of $45\text{ mH}$ and $80\text{ mH}$ . Assuming there is no mutual magnetic coupling between the coils, what is the total equivalent inductance of the circuit in millihenries ( $\text{mH}$ )?

Cevabı ve açıklamayı göster

Cevap: 125

Cevap

125

When inductors are connected in series without mutual inductance, their magnetic opposition to current changes accumulates directly, meaning the total inductance is simply the sum of the individual inductances (

45\text{ mH} + 80\text{ mH} = 125\text{ mH}

).

Adım Adım Çözüm

1

Recall the formula for combining series inductances without mutual magnetic coupling.

L_{\text{total}} = L_1 + L_2

Like series resistors, total series inductance is the direct sum of individual inductances when there is no magnetic interaction.

2

Add the two individual inductance values together.

45\text{ mH} + 80\text{ mH} = 125\text{ mH}

Direct addition provides the equivalent total inductance in millihenries.

Anahtar Kavram

Inductors in series combine by direct addition, identical to the rule for resistors in series.

Tahmini Süre:45s

Soru 43Soru →

Match each electromagnetic component to its primary operating principle or function.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Solenoid pairs with converting electrical energy into linear mechanical motion; Transformer pairs with transferring electrical energy via mutual electromagnetic induction; Relay pairs with using an electromagnet to actuate switch contacts; Inductor pairs with storing energy in a magnetic field to oppose current changes.

Each electromagnetic component performs a unique function based on electromagnetic principles: solenoids produce direct mechanical stroke; transformers transfer power across isolated windings via alternating magnetic flux; relays actuate circuit contacts remotely via electromagnetic force; and inductors provide inductive reactance and self-induced counter-EMF.

Adım Adım Çözüm

1

Identify the primary mechanism of a solenoid.

A solenoid converts magnetic force into linear mechanical movement.

When energized, the coil's magnetic field draws an iron core inward to actuate a mechanical load.

2

Identify the operating principle of a transformer.

A transformer utilizes mutual induction across coupled coils.

Changing current in the primary coil induces an alternating voltage in the secondary coil without direct electrical connection.

3

Identify the primary function of an electromechanical relay.

A relay operates switch contacts using electromagnetic attraction.

An electromagnet pulls an armature to switch a separate circuit on or off.

4

Identify the foundational circuit property of an inductor.

An inductor stores magnetic energy and opposes changes in current flow.

By Lenz's and Faraday's laws of induction, self-inductance generates counter-electromotive force when current changes.

Anahtar Kavram

Electromagnetic Components and Operating Principles

Tahmini Süre:45s

Soru 44Soru →

A direct current (DC) automotive lamp connected to a $12\text{ V}$ power source draws a current of $2\text{ A}$ . What is the total electrical power consumed by the lamp?

6\text{ W}

14\text{ W}

24\text{ W}

48\text{ W}

Cevabı ve açıklamayı göster

Cevap: $24\text{ W}$

Cevap

24\text{ W}

According to Watt's Law, the electrical power (

P

) consumed by a circuit load is equal to the voltage (

V

) across the component multiplied by the current (

I

) flowing through it:

P = V \times I

. Substituting the given values yields

P = 12\text{ V} \times 2\text{ A} = 24\text{ W}

.

Adım Adım Çözüm

1

Identify the given circuit parameters

Voltage (

V

) =

12\text{ V}

, Current (

I

) =

2\text{ A}

These are the two electrical quantities necessary to calculate power directly.

2

Select the appropriate electrical power formula (Watt's Law)

P = V \times I

When voltage and current are known, power is equal to their product.

3

Substitute the given values into the formula and calculate

P = 12\text{ V} \times 2\text{ A} = 24\text{ W}

Multiplying electromotive force by current gives total power in watts.

Anahtar Kavram

Electrical power in a DC circuit is calculated using Watt's Law (

P = V \times I

), where power in watts is the product of voltage in volts and current in amperes.

Tahmini Süre:45s

Soru 45Soru →

An automotive technician is replacing a damaged section of wiring in a 12-volt vehicle circuit. If the replacement copper wire has the same length as the original wire but a smaller American Wire Gauge (AWG) number, what effect will this have on the wire's electrical resistance?

The electrical resistance will increase because a lower gauge number corresponds to a narrower wire.

The electrical resistance will decrease because a lower gauge number corresponds to a larger cross-sectional area.

The electrical resistance will remain constant because resistance depends solely on conductor length.

The electrical resistance will drop to zero because changing gauge eliminates all opposition to current.

Cevabı ve açıklamayı göster

Cevap: The electrical resistance will decrease because a lower gauge number corresponds to a larger cross-sectional area.

Cevap

The electrical resistance will decrease because a lower gauge number corresponds to a larger cross-sectional area.

In the American Wire Gauge (AWG) standard, gauge numbers are inversely related to physical wire diameter. A conductor with a smaller AWG number has a larger diameter and therefore a greater cross-sectional area. According to the formula

R = \rho \frac{L}{A}

, resistance is inversely proportional to cross-sectional area when material resistivity and length are constant. Thus, replacing a wire with one of a smaller AWG number results in lower electrical resistance.

Adım Adım Çözüm

1

Identify the relationship between the American Wire Gauge (AWG) scale and conductor diameter.

In the AWG standard, smaller numerical gauge numbers designate thicker conductors with larger cross-sectional areas (

A

).

The AWG numbering system is inverse; as the gauge number decreases, the physical diameter of the wire increases.

2

Apply the physical resistance formula:

R = \rho \frac{L}{A}

.

Because conductor length (

L

) and material resistivity (

\rho

) remain unchanged, increasing cross-sectional area (

A

) reduces total electrical resistance (

R

).

Electrical resistance is inversely proportional to the cross-sectional area of the conductor.

Anahtar Kavram

Relationship between American Wire Gauge (AWG), cross-sectional area, and electrical resistance (

R = \rho \frac{L}{A}

)

Soru 46Soru →

An auxiliary electric bilge pump operates on a $12\text{ V}$ DC power supply. If the internal electrical resistance of the pump motor is $6\ \Omega$ , what is the steady-state current drawn by the pump during operation?

0.5\text{ A}

2\text{ A}

6\text{ A}

72\text{ A}

Cevabı ve açıklamayı göster

Cevap: $2\text{ A}$

Cevap

The current drawn by the pump is

2\text{ A}

.

According to Ohm's Law, current (

I

) equals voltage (

V

) divided by resistance (

R

). Dividing the

12\text{ V}

supply by the

6\ \Omega

load resistance yields exactly

2\text{ A}

.

Adım Adım Çözüm

1

Identify the given circuit parameters and the formula to solve for unknown current.

Given: Voltage

V = 12\text{ V}

, Resistance

R = 6\ \Omega

. Ohm's Law states

V = I \times R

, which rearranges to

I = \frac{V}{R}

.

Ohm's Law defines the fundamental mathematical relationship between voltage, current, and resistance in a direct current circuit.

2

Substitute the given values into the rearranged formula and compute the current.

I = \frac{12\text{ V}}{6\ \Omega} = 2\text{ A}

.

Carrying out the division provides the magnitude of electron flow (amperage) through the load.

Anahtar Kavram

Ohm's Law formula for calculating current:

I = \frac{V}{R}

Tahmini Süre:40s

Soru 47Soru →

An electrical test bench delivers a constant $80\text{ V}$ direct-current supply to four separate parallel circuit arrangements. Match each circuit configuration on the left with its corresponding equivalent resistance ( $R_{eq}$ ) and total supply current ( $I_T$ ) on the right.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

The configuration with

40\ \Omega

and

10\ \Omega

matches

R_{eq} = 8\ \Omega, I_T = 10\text{ A}

; four

64\ \Omega

elements match

R_{eq} = 16\ \Omega, I_T = 5\text{ A}

; three branches of

120\ \Omega, 60\ \Omega, 40\ \Omega

match

R_{eq} = 20\ \Omega, I_T = 4\text{ A}

; and two branches of

150\ \Omega, 75\ \Omega

match

R_{eq} = 50\ \Omega, I_T = 1.6\text{ A}

.

In any direct-current parallel network, the total equivalent resistance (

R_{eq}

) is calculated using the reciprocal formula

\frac{1}{R_{eq}} = \sum \frac{1}{R_n}

(or

R/N

for identical branches). Total current drawn from the supply is determined by Ohm's Law:

I_T = \frac{V_S}{R_{eq}}

. Evaluating each configuration against the constant

80\text{ V}

bus correctly establishes all four resistance and current pairs.

Adım Adım Çözüm

1

Calculate the equivalent resistance and total current for the

40\ \Omega

and

10\ \Omega

parallel branch pair.

R_{eq} = \frac{40 \times 10}{40 + 10} = 8\ \Omega

;

I_T = \frac{80\text{ V}}{8\ \Omega} = 10\text{ A}

.

Two unequal parallel resistors follow the product-over-sum rule, and total current is determined by Ohm's Law (

I = V/R

).

2

Calculate the equivalent resistance and current for the four parallel

64\ \Omega

elements.

R_{eq} = \frac{64}{4} = 16\ \Omega

;

I_T = \frac{80\text{ V}}{16\ \Omega} = 5\text{ A}

.

Identical parallel resistors simplify to branch resistance divided by the number of branches (

R/N

).

3

Calculate the equivalent resistance and current for the three parallel branches (

120\ \Omega, 60\ \Omega, 40\ \Omega

).

\frac{1}{R_{eq}} = \frac{1}{120} + \frac{2}{120} + \frac{3}{120} = \frac{6}{120} = \frac{1}{20} \implies R_{eq} = 20\ \Omega

;

I_T = \frac{80\text{ V}}{20\ \Omega} = 4\text{ A}

.

Three or more unequal parallel branches require finding the reciprocal sum over a common denominator.

4

Calculate the equivalent resistance and current for the

150\ \Omega

and

75\ \Omega

parallel branches.

R_{eq} = \frac{150 \times 75}{150 + 75} = \frac{11250}{225} = 50\ \Omega

;

I_T = \frac{80\text{ V}}{50\ \Omega} = 1.6\text{ A}

.

Applying product-over-sum and dividing bus voltage by equivalent resistance yields the total circuit current.

Anahtar Kavram

Parallel circuit rules require that full bus voltage appears across each branch, equivalent resistance is always lower than the smallest branch resistance, and total current equals the sum of all individual branch currents.

Tahmini Süre:2m 0s

Soru 48Soru →

Match each wire preparation hand tool with its primary function in electrical fabrication.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Wire strippers match with removing insulation without damaging the inner wire core; Diagonal cutting pliers match with cutting conductors cleanly and trimming excess lead wires; Crimping tool matches with deforming and securing solderless terminal lugs onto bare wire ends; Cable jacket ripper matches with slitting open the outer protective sheath of a multi-conductor cable.

Each tool in wire preparation performs a dedicated function: wire strippers cleanly remove outer insulation without nicking the core; diagonal cutting pliers cut wires and component leads flush; crimpers mechanically compress terminals onto stripped conductors; and cable jacket rippers slit the outer sheath of multi-wire cables.

Adım Adım Çözüm

1

Identify the primary purpose of wire strippers.

Matched with removing insulation from a single conductor without damaging the inner wire core.

Wire strippers use calibrated notches matched to wire gauge to score and remove insulation cleanly.

2

Identify the primary purpose of diagonal cutting pliers (dikes).

Matched with cutting conductors cleanly to length and trimming excess lead wires.

Diagonal cutters have sharp bypass or bevel jaws intended strictly for slicing copper wires and trimming leads.

3

Identify the primary purpose of a crimping tool.

Matched with deforming and securing solderless terminal lugs onto bare wire ends.

Crimpers compress metal terminal barrels around exposed wire strands to create a tight mechanical and electrical bond.

4

Identify the primary purpose of a cable jacket ripper.

Matched with slitting open the outer protective sheath of a multi-conductor cable.

Cable jacket rippers cut through heavy exterior sheathing to expose the internal bundled wires.

Anahtar Kavram

Identifying dedicated wire preparation tools and their correct mechanical applications

Tahmini Süre:45s

Soru 49Soru →

An electrician is preparing to connect a solid copper conductor to a standard screw terminal. Arrange the following steps in the correct operational sequence using the proper electrical hand tools.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

1. Strip the conductor using a wire stripper. 2. Form a loop in the bare copper with needle-nose pliers. 3. Hook the wire clockwise around the screw post. 4. Tighten the terminal screw with a screwdriver.

The correct operational sequence begins by using wire strippers with the proper gauge notch to cleanly remove insulation without nicking the conductor. Needle-nose pliers are then used to bend the bare copper into a hook. The hook is placed clockwise around the screw post so that tightening rotation draws the wire inward. Finally, an appropriately sized screwdriver fastens the terminal screw securely.

Adım Adım Çözüm

1

Use the correctly sized gauge notch of a wire stripper to strip insulation from the conductor end.

Exposes undamaged, bare solid copper wire.

Proper notch selection prevents nicking, which can weaken the solid wire.

2

Grip the bare conductor end with needle-nose pliers and form a 3/4-circle loop.

Produces a clean hook sized to fit the terminal screw diameter.

Needle-nose pliers allow precise shaping without distorting or scarring the copper.

3

Position the hook around the terminal screw post facing clockwise.

The loop opening aligns with the clockwise tightening rotation of the screw.

Clockwise placement ensures rotational friction from the screw draws the wire tighter around the shank.

4

Drive the screw down firmly using a matching insulated screwdriver.

Creates a secure, low-resistance electrical connection.

Proper screwdriver sizing ensures adequate torque without camming out or damaging the screw head.

Anahtar Kavram

Standard hand-tool procedure for terminating solid conductors under screw terminals, including tool selection and clockwise loop orientation.

Tahmini Süre:1m 0s

Soru 50Soru →

A passenger sedan maintains proper ride height and dampens vertical road impacts normally, but it leans excessively toward the outside when making sharp turns. Which suspension component is specifically designed to resist this lateral body roll?

Shock absorber

Coil spring

Stabilizer bar

Ball joint

Cevabı ve açıklamayı göster

Cevap: Stabilizer bar

Cevap

The stabilizer bar (sway bar) is the component engineered to resist lateral chassis lean during cornering.

The stabilizer bar, also known as a sway bar or anti-roll bar, is a transverse steel torsion bar that connects the left and right suspension control arms. When cornering forces compress the outside suspension and extend the inside suspension, the bar twists and transfers load, pulling the chassis back level and minimizing body roll.

Adım Adım Çözüm

1

Analyze the vehicle symptom and operating condition.

The vehicle handles normal vertical bumps smoothly without bouncing or sagging, but experiences excessive lean when cornering.

Isolating cornering body roll from vertical ride height and damping isolates the stabilizer linkage from springs and dampers.

2

Identify the component designed to transfer torsional load across the vehicle axle.

The stabilizer bar connects the left and right control arms, twisting to counteract unequal suspension travel during cornering.

Springs support weight and shock absorbers dampen bounce, whereas the stabilizer bar provides anti-roll stiffness.

Anahtar Kavram

Function and operating principle of a stabilizer bar in controlling vehicle body roll

Tahmini Süre:1m 0s

Soru 51Soru →

Arrange the steps in the correct sequence to illustrate how fuel vapors move through an automotive Evaporative Emission Control (EVAP) system from initial generation to combustion.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence begins with gasoline evaporating in the fuel tank, followed by vapor storage in the charcoal canister, opening of the purge valve by the engine computer, and finally intake manifold vacuum drawing the vapors into the engine cylinders for combustion.

The Evaporative Emission Control (EVAP) system is designed to prevent unburned hydrocarbon vapors from escaping into the environment. The sequence begins when liquid gasoline warms up and evaporates inside the fuel tank. These vapors are routed through dedicated vent lines into a charcoal canister containing activated carbon that absorbs and stores them. When the engine reaches proper operating conditions, the powertrain control module opens the purge valve, allowing engine intake vacuum to draw the stored vapors out of the canister and into the combustion chambers where they are cleanly burned.

Adım Adım Çözüm

1

Identify the origin point of the emissions.

Gasoline evaporates inside the sealed fuel tank.

The process begins when liquid fuel heats up and creates hydrocarbon vapors.

2

Determine where the vapors are routed and held while the engine is off or idling.

Vapors travel to and are absorbed by the charcoal canister.

The canister holds the vapors until the engine is ready to burn them.

3

Identify the control mechanism that initiates purging.

The engine control computer commands the purge valve to open.

The purge valve acts as the gate that regulates when stored vapors can enter the intake system.

4

Determine the final pathway and disposal of the vapors.

Engine vacuum pulls the vapors into the cylinders for combustion.

Burning the fuel vapors inside the engine cylinders safely disposes of the hydrocarbons without atmospheric pollution.

Anahtar Kavram

Evaporative Emission Control (EVAP) system operation and fuel vapor pathway

Tahmini Süre:45s

Soru 52Soru →

A technician is troubleshooting a power supply circuit featuring a full-wave bridge rectifier composed of four standard silicon diodes. During each single half-cycle of the alternating current (AC) input signal, how many of the four diodes conduct current simultaneously through the load?

Only one diode conducts while the remaining three diodes stay idle.

Two diodes conduct while the remaining two diodes are reverse-biased.

All four diodes conduct simultaneously in parallel to share the load current.

Three diodes conduct in series while one diode blocks the return path.

Cevabı ve açıklamayı göster

Cevap: Two diodes conduct while the remaining two diodes are reverse-biased.

Cevap

Two diodes conduct while the remaining two diodes are reverse-biased.

In a standard four-diode bridge rectifier, alternating current (AC) is converted to pulsating direct current (DC) by routing current through pairs of diodes. During any given half-cycle, two diagonally opposite diodes are forward-biased and conduct current through the load in a single direction, while the other two diodes are reverse-biased and block conduction.

Adım Adım Çözüm

1

Analyze the bridge rectifier circuit topology under an AC input half-cycle

One AC input terminal is positive with respect to the other terminal.

AC voltage alternates polarity every half-cycle, determining the bias conditions of each diode in the bridge.

2

Trace the current flow through the forward-biased diodes and the load

Current enters the bridge, passes through one forward-biased diode, travels through the load resistor, and returns through a second forward-biased diode to the opposite AC line.

A complete circuit path requires a forward and return path through the bridge network.

3

Determine the state of the remaining two diodes

The opposite pair of diodes experiences reverse bias and blocks current flow.

Diodes only conduct when their anode is more positive than their cathode.

Anahtar Kavram

Full-Wave Bridge Rectification and Diode Conduction Pairs

Tahmini Süre:1m 0s

Soru 53Soru →

Pure elemental silicon and germanium serve as the foundation of modern solid-state electronics due to their intermediate electrical conductivity. What atomic characteristic distinguishes these Group IV elements as semiconductors?

They contain only one weakly held outer electron that drifts freely between atomic nuclei.

They have exactly four valence electrons in their outermost shell, creating a stable covalent lattice under normal conditions.

They feature a full valence shell of eight electrons that completely blocks electrical charge movement.

They maintain a permanent net positive charge that actively opposes the flow of conventional current.

Cevabı ve açıklamayı göster

Cevap: They have exactly four valence electrons in their outermost shell, creating a stable covalent lattice under normal conditions.

Cevap

Pure silicon and germanium are classified as semiconductors because their atoms possess four valence electrons in their outermost shell, forming covalent bonds that yield intermediate electrical conductivity.

Semiconductors such as silicon (

Si

) and germanium (

Ge

) belong to Group IV of the periodic table and have four valence electrons in their outer shell. In crystalline form, each atom shares these four electrons with adjacent atoms via covalent bonds, resulting in electrical conductivity that lies midway between conductors (which typically have

1

to

3

loosely held valence electrons) and insulators (which typically have

5

to

8

tightly held valence electrons).

Adım Adım Çözüm

1

Determine the valence electron configuration of Group IV elements like silicon and germanium.

Both silicon (

Si

) and germanium (

Ge

) possess exactly

4

valence electrons in their outer energy shell.

The number of outer-shell valence electrons dictates how easily charge carriers can be released for electrical conduction.

2

Compare the valence count of semiconductors with conductors and insulators.

Conductors generally have

1

to

3

valence electrons, semiconductors have exactly

4

, and insulators typically have

5

to

8

tightly bound valence electrons.

With

4

valence electrons, neighboring atoms share electrons in covalent bonds, making pure semiconductors moderate conductors at room temperature.

Anahtar Kavram

Semiconductor atomic structure and valence electrons

Tahmini Süre:1m 0s

Soru 54Soru →

When a vehicle equipped with a standard open differential has one drive wheel on dry pavement and the other on slick ice, which of the following describes what happens when the driver presses the accelerator?

Both drive wheels turn at identical speeds to prevent either tire from slipping.

Torque is automatically shifted exclusively to the wheel on dry pavement.

The wheel on ice spins rapidly while the wheel on dry pavement receives very little driving torque.

The differential locks both axle shafts together to propel the vehicle forward.

Cevabı ve açıklamayı göster

Cevap: The wheel on ice spins rapidly while the wheel on dry pavement receives very little driving torque.

Cevap

The wheel on ice spins rapidly while the wheel on dry pavement receives very little driving torque.

A standard open differential always applies equal torque to both drive wheels. The maximum torque it can send to either wheel is limited by whichever tire loses traction first. When one wheel is on slick ice, it requires almost no torque to spin, meaning the wheel on dry pavement receives only that same near-zero amount of torque, leaving the vehicle unable to move.

Adım Adım Çözüm

1

Analyze the fundamental operating principle of a standard open differential.

An open differential distributes equal torque (a 50/50 split) to both drive wheels at all times.

The bevel spider gears inside the carrier balance torque evenly between the left and right side gears.

2

Determine how traction loss affects torque delivery.

The total usable torque delivered to both drive wheels is limited to the amount of torque required to spin the wheel with the lowest grip.

Because the wheel on slick ice has almost zero traction resistance, very little torque can build up before it slips.

3

Identify the resulting behavior of each wheel.

The wheel on ice spins freely while the wheel on dry pavement remains stationary due to insufficient driving torque.

The high-traction wheel receives only the same minimal torque as the spinning wheel, which is not enough to overcome the vehicle's inertia.

Anahtar Kavram

Open differential torque distribution on split-traction surfaces

Tahmini Süre:45s

Soru 55Soru →

In a combination valve on a front-disc and rear-drum braking system, what is the primary function of the metering valve?

It limits hydraulic line pressure delivered to the rear brakes during rapid stops to prevent wheel lockup.

It delays fluid pressure to the front disc brakes until the rear brake shoes overcome return spring tension.

It maintains a slight residual pressure in the hydraulic lines to keep air from entering the wheel cylinders.

It senses pressure drops between split hydraulic circuits and triggers the instrument panel warning light.

Cevabı ve açıklamayı göster

Cevap: It delays fluid pressure to the front disc brakes until the rear brake shoes overcome return spring tension.

Cevap

The metering valve delays fluid pressure to the front disc brakes until the rear brake shoes overcome return spring tension.

Because disc brake pads have zero clearance from the rotor while drum shoes must push against return springs to reach the drum, disc brakes apply faster. The metering valve (hold-off valve) prevents fluid flow to the front disc calipers until hydraulic pressure builds sufficiently to overcome the rear drum springs, ensuring balanced initial braking.

Adım Adım Çözüm

1

Analyze the mechanical differences between disc and drum brake actuation

Disc brake pads sit directly against the rotor and apply instantly with fluid movement, whereas drum brake shoes must first overcome return spring tension and travel through clearance to reach the drum.

Without timing correction, front disc brakes would engage significantly before the rear drum brakes during light pedal application.

2

Identify the specific valve component that regulates this initial timing difference

The metering valve (hold-off valve) blocks hydraulic pressure to the front disc calipers until line pressure reaches approximately 75 to 125 psi.

This slight pressure threshold ensures the rear shoes make contact with the drums so all four wheels begin braking at the same time, preventing front-end dive.

Anahtar Kavram

Hydraulic timing and balance between disc and drum brake assemblies via the metering valve

Tahmini Süre:1m 0s

Soru 56Soru →

During a land navigation exercise, an instructor maps out 150 possible waypoint coordinates. Of these waypoints, 45 are located in dense forest, 35 are in open terrain, 50 are near water features, and the remaining waypoints are on elevated ridges. If a cadet is randomly assigned one waypoint coordinate, what is the probability that it is located on an elevated ridge? (Express your answer as a simplified fraction)

Cevabı ve açıklamayı göster

Cevap: 2/15; 2 / 15

Cevap

2/15

The correct probability is found by dividing the number of ridge waypoints (20) by the total number of waypoints (150). Simplifying the fraction 20/150 yields 2/15.

Adım Adım Çözüm

1

Determine the total number of possible outcomes.

Total waypoints = 150.

The denominator for a single event probability calculation is the total number of items in the set.

2

Calculate the number of favorable outcomes (elevated ridge waypoints).

150 - (45 + 35 + 50) = 150 - 130 = 20 waypoints on elevated ridges.

You must subtract the sum of all known waypoint categories from the total to find the unknown remainder.

3

Set up the probability ratio and simplify the fraction.

20 / 150 simplifies to 2 / 15.

Probability is the number of favorable outcomes divided by total outcomes. ASVAB format requires fractions to be reduced to their lowest terms.

Anahtar Kavram

Single Event Probability

Soru 57Soru →

In an electronic ignition system, several sequential events must take place to ignite the compressed air-fuel mixture in a cylinder. Arrange the following operational steps in chronological order, from initial engine position detection to cylinder combustion. What is the correct sequence of these events?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct chronological sequence begins with the crankshaft position sensor transmitting a timing signal, followed by the engine control module interrupting the primary circuit, which causes the coil magnetic field to collapse and induce high secondary voltage, and finishes with the high-voltage pulse jumping the spark plug gap.

The correct sequence follows the fundamental flow of modern electronic ignition: sensing engine position (crankshaft sensor), command switching (module cuts primary current), voltage step-up (collapsing magnetic field induces secondary high voltage), and spark discharge (arc jumps the spark plug electrode gap).

Adım Adım Çözüm

1

Identify the initiating trigger event in the electronic ignition system.

The crankshaft position sensor monitors engine rotation and provides the timing baseline signal to the control unit.

Electronic systems cannot determine when to fire without initial position input from the engine rotation sensor.

2

Determine the control response to the trigger signal.

The engine control module opens the primary ignition circuit, interrupting low-voltage battery current.

Breaking the primary circuit is the mechanical or solid-state action required to collapse the coil's magnetic field.

3

Trace the magnetic induction response inside the ignition coil.

The collapsing magnetic field cuts through thousands of fine secondary winding turns, stepping up the potential into tens of thousands of volts.

Mutual induction converts low-voltage primary switching into the high-voltage spike needed for ignition.

4

Identify the delivery and combustion stage.

The high-voltage surge reaches the spark plug and arcs across the gap, igniting the compressed charge.

The electrical arc at the spark plug electrodes is the final operational objective of the ignition circuit.

Anahtar Kavram

Electronic Ignition Triggering and High-Voltage Induction Sequence

Tahmini Süre:45s

Soru 58Soru →

Match each internal engine component to its primary mechanical role.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Oil control ring matches scraping excess lubricating oil from the cylinder wall; Piston skirt matches maintaining vertical piston alignment in the cylinder bore; Valve guide matches providing radial support and precise alignment for the reciprocating valve stem; Cam lobe matches converting rotary shaft motion into timed linear lift to open an intake or exhaust valve.

Each internal engine component performs a specific mechanical task: the oil control ring scrapes surplus lubricant from the cylinder wall; the piston skirt stabilizes the piston against lateral rocking; the valve guide provides straight-line sleeve support for the moving valve stem; and the cam lobe transforms shaft rotation into mechanical lift to open valves.

Adım Adım Çözüm

1

Identify the primary function of the lowest piston ring assembly (oil control ring).

The oil control ring regulates cylinder wall lubrication film thickness and scrapes surplus oil down to the crankcase.

Prevents oil consumption and exhaust fouling while maintaining necessary lubrication.

2

Analyze the structural role of the piston skirt extending below the ring lands.

The skirt stabilizes the piston body against lateral thrust loads created by the connecting rod angle.

Prevents piston slap, cocking, and excessive bore wear.

3

Determine the mechanical purpose of the valve guide inside the cylinder head.

The guide acts as a sleeve bearing that keeps the reciprocating valve stem in strict linear alignment.

Ensures true concentric seating between the valve face and valve seat.

4

Examine the kinematic conversion performed by a camshaft lobe.

The egg-shaped cam lobe converts rotary motion from the camshaft into linear displacement to actuate the valvetrain.

Determines the timing, lift distance, and open duration of intake and exhaust valves.

Anahtar Kavram

Internal engine component specialization and valvetrain kinematics

Tahmini Süre:1m 0s

Soru 59Soru →

Within the rear axle housing of a vehicle, what primary function is served by the hypoid ring and pinion gear set?

Allowing the outer drive wheel to spin faster than the inner drive wheel during a turn

Changing the direction of rotational power by 90 degrees while providing gear reduction

Compensating for changes in the operating length of the driveshaft during suspension travel

Balancing hydraulic fluid pressure equally between the left and right brake mechanisms

Cevabı ve açıklamayı göster

Cevap: Changing the direction of rotational power by 90 degrees while providing gear reduction

Cevap

Changing the direction of rotational power by 90 degrees while providing gear reduction

The hypoid ring and pinion gear set receives longitudinal rotational torque from the driveshaft via the drive pinion, meshes at a 90-degree angle with the ring gear to drive the transverse axle shafts, and provides gear reduction to increase torque to the wheels.

Adım Adım Çözüm

1

Identify the orientation and mechanical connection of the input and output shafts.

The driveshaft delivers torque longitudinally along the length of the vehicle, while the drive axles must rotate transversely (perpendicularly) to turn the wheels.

Power must be redirected 90 degrees to drive the vehicle's wheels.

2

Determine the role of the hypoid ring and pinion gear set in transferring this power.

The smaller drive pinion turns the larger ring gear, redirecting rotation 90 degrees and creating a permanent gear reduction ratio that multiplies engine torque.

The hypoid gear design allows smooth, quiet mesh below the axle centerline while accomplishing the directional change and final drive torque multiplication.

Anahtar Kavram

Hypoid ring and pinion gear function in the final drive assembly

Tahmini Süre:1m 0s

Soru 60Soru →

In electronic systems, standard PN-junction and specialized diodes exhibit distinct electrical behaviors depending on bias polarity and operating conditions. Match each diode operating condition with its characteristic electrical behavior.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Standard silicon diode in forward bias matches conducting current readily with an approximate

0.7\text{ V}

potential drop; Standard silicon diode in reverse bias matches blocking current flow with high resistance and negligible leakage; Zener diode in reverse breakdown matches maintaining a constant reference voltage across a range of currents; Light-emitting diode in forward bias matches releasing optical energy through electron-hole recombination.

Each diode state corresponds directly to its semiconductor junction physics: a forward-biased silicon diode exhibits a characteristic

0.7\text{ V}

barrier drop during conduction; a reverse-biased PN junction widens its depletion region to block current; a Zener diode exploits controlled reverse breakdown for voltage stabilization; and an LED emits light via radiative recombination under forward bias.

Adım Adım Çözüm

1

Analyze standard forward bias characteristics of silicon diodes.

Identified that overcoming the silicon barrier potential (

0.7\text{ V}

) permits large forward current conduction with a steady

0.7\text{ V}

drop.

Forward bias narrows the depletion region once the threshold voltage is reached.

2

Analyze standard reverse bias behavior below breakdown limits.

Identified that reverse bias widens the depletion layer, preventing majority carrier flow and resulting in high resistance.

A reverse-biased PN junction acts essentially as an open circuit.

3

Analyze specialized Zener diode reverse breakdown operation.

Identified that reverse-biased Zener diodes hold a stable breakdown voltage across varying currents.

Controlled avalanche/Zener breakdown enables voltage regulation applications.

4

Analyze light-emitting diode (LED) forward conduction mechanics.

Identified that forward current injection causes radiative recombination emitting photons.

Electrons dropping across the direct bandgap release energy as light.

Anahtar Kavram

Diode Operating States and Biasing Characteristics

Tahmini Süre:1m 0s

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram