Tüm alıştırma soruları

Soru 1081Soru →

A four-band carbon resistor displays the color bands Orange, Orange, Brown, and Gold in sequence from left to right. What is the nominal resistance value of this component?

331\ \Omega

33\ \Omega

330\ \Omega

3.3\text{ k}\Omega

Cevabı ve açıklamayı göster

Cevap: $330\ \Omega$

Cevap

330\ \Omega

The first band (Orange) represents the digit 3, the second band (Orange) represents the digit 3, and the third band (Brown) represents a multiplier of

10^1

(10). Multiplying the significant digits by the multiplier yields

33 \times 10 = 330\ \Omega

.

Adım Adım Çözüm

1

Decode the first two significant color bands.

Orange corresponds to 3, and the second Orange corresponds to 3, giving the two-digit number 33.

In a 4-band resistor code, the first two bands represent the base significant digits.

2

Determine the multiplier from the third color band.

Brown corresponds to a multiplier of

10^1

(or

10

).

The third band indicates the power of ten by which the significant digits are multiplied.

3

Multiply the significant digits by the multiplier value.

33 \times 10 = 330\ \Omega

.

Combining the base digits and multiplier gives the nominal resistance rating.

Anahtar Kavram

Four-Band Resistor Color Code Decoding

Tahmini Süre:35s

Soru 1082Soru →

Electronic circuits utilize specialized protective devices to safeguard equipment from overcurrent, sustained thermal overload, and transient overvoltage conditions. Match each protective component on the left with its primary operational characteristic on the right.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Fast-Acting Fuse pairs with the description of a fine, low-mass conductor link that melts almost instantaneously to protect sensitive semiconductors; Time-Delay (Slow-Blow) Fuse pairs with the description of a dual-element design that tolerates brief startup inrush currents while clearing sustained overloads; Magnetic Circuit Breaker pairs with the description of a solenoid coil whose electromagnetic field trips a mechanical latch during short circuits; Metal Oxide Varistor (MOV) pairs with the description of a voltage-dependent resistor that clamps transient overvoltage spikes by shunting surge energy to ground.

Each match accurately pairs the protective component with its core physical operating principle: Fast-acting fuses provide rapid, sacrificial clearing for delicate components; time-delay fuses accommodate temporary motor start-up surges without nuisance blowing; magnetic circuit breakers leverage electromagnetic solenoids for instantaneous short-circuit interruption; and metal oxide varistors (MOVs) provide nonlinear resistance to clamp transient high-voltage spikes.

Adım Adım Çözüm

1

Analyze overcurrent versus overvoltage protection roles.

Identify that the Metal Oxide Varistor (MOV) is specifically an overvoltage surge suppression component, distinguishing it from the current-limiting fuses and circuit breaker.

MOVs clamp excess line voltage rather than breaking series current flow directly.

2

Distinguish between the response speeds and architectures of the two fuse types.

Match the fast-acting fuse to immediate clearing of low-energy circuits, and the time-delay fuse to circuits requiring high inrush current tolerance (such as inductive motor loads).

Time-delay fuses use dual elements or thermal delay mechanisms to prevent nuisance blowing during normal startup surges.

3

Examine the operating mechanism of the circuit breaker.

Connect the magnetic circuit breaker to the electromagnetic solenoid coil tripping mechanism.

Magnetic circuit breakers operate instantaneously based on electromagnetic attraction generated by fault currents rather than thermal expansion.

Anahtar Kavram

Operating Principles and Application Categories of Circuit Protective Devices

Tahmini Süre:1m 30s

Soru 1083Soru →

An industrial direct-current (DC) indicator lamp dissipates $1.8\text{ W}$ of power when a current of $150\text{ mA}$ flows through it. What is the voltage drop across the lamp, in volts?

Cevabı ve açıklamayı göster

Cevap: 12

Cevap

The voltage drop across the indicator lamp is

12\text{ V}

.

According to Watt's Law, electrical power is the product of voltage and current (

P = V \times I

). Rearranging the formula to solve for voltage gives

V = \frac{P}{I}

. Converting

150\text{ mA}

to

0.15\text{ A}

and evaluating

\frac{1.8\text{ W}}{0.15\text{ A}}

yields

12\text{ V}

.

Adım Adım Çözüm

1

Convert the current from milliamperes to amperes.

I = 150\text{ mA} = 0.15\text{ A}

Standard electrical formulas require current in base units of amperes (A).

2

Rearrange Watt's Law to solve for voltage.

V = \frac{P}{I}

Watt's Law defines power as

P = V \times I

, so isolating voltage yields

V = \frac{P}{I}

.

3

Substitute the known values into the equation to find the voltage.

V = \frac{1.8\text{ W}}{0.15\text{ A}} = 12\text{ V}

Dividing the power dissipation (

1.8\text{ W}

) by the current (

0.15\text{ A}

) gives the operating voltage.

Anahtar Kavram

Watt's Law describes the mathematical relationship between electrical power, voltage, and current:

P = V \times I

. When power and current are known, voltage is calculated using

V = \frac{P}{I}

, provided current is expressed in amperes.

Tahmini Süre:1m 0s

Soru 1084Soru →

An electronics technician is setting up a digital multimeter (DMM) to perform several diagnostic checks on a circuit test bench. Match each measurement task to its correct meter input jack, dial setting, and circuit connection method.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Match small DC current (

18\text{ mA}

) with the

\text{mA}/\mu\text{A}

jack in series; match

120\text{ V}

AC line voltage with the

\text{V}/\Omega

jack on

\text{ACV}

in parallel; match heavy DC current (

7.5\text{ A}

) with the dedicated

10\text{A}

jack in series; match

24\text{ V}

DC potential difference with the

\text{V}/\Omega

jack on

\text{DCV}

in parallel.

Correct multimeter configuration requires matching three parameters: (1) connection topology (parallel for voltage, series for current), (2) input terminal selection (standard

\text{V}/\Omega

for voltage, low-current

\text{mA}/\mu\text{A}

for values under

400\text{ mA}

, and separate

10\text{A}

terminal for high current), and (3) function selection matching waveform type (DC vs. AC).

Adım Adım Çözüm

1

Determine connection topology based on measurement quantity (Voltage vs. Current)

Voltmeters must always be connected in parallel across components, while ammeters must always be placed in series by breaking the circuit path.

Voltmeters have high internal input impedance (

>10\text{ M}\Omega

) to prevent loading, whereas ammeters have near-zero internal resistance to allow current flow.

2

Select input jacks based on expected signal magnitude and function

Voltage readings use the

\text{V}/\Omega

and

\text{COM}

jacks. Current below

400\text{ mA}

uses the

\text{mA}/\mu\text{A}

jack, while high current (

7.5\text{ A}

) requires the separate

10\text{A}

high-current terminal.

Exceeding the current rating of the low-current jack will immediately blow the internal protective fuse.

3

Select dial settings based on waveform type (AC vs. DC)

Use

\text{ACV}

for

120\text{ V}_{\text{RMS}}

utility power,

\text{DCV}

for

24\text{ V}

filtered direct potential,

\text{DC mA}

for

18\text{ mA}

, and

10\text{A DC}

for

7.5\text{ A}

.

Setting an AC mode on a DC signal or vice versa leads to erroneous readings or reading zero due to average vs. RMS rectification filtering.

Anahtar Kavram

Multimeter Lead Placement, Jack Selection, and Dial Configuration

Tahmini Süre:2m 0s

Soru 1085Soru →

An electrical technician is assembling conduit raceways, enclosure boxes, and data distribution hardware for a commercial installation. Match each specialized electrical hand tool to its primary function.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Fish tape matches pulling conductors through raceways; Punch-down tool matches terminating and trimming data conductors into IDC blocks; Conduit bender matches forming precise bends and offsets in electrical metallic tubing; Knockout punch matches cutting circular openings in sheet metal enclosures.

Each tool is matched to its intended electrical installation function: fish tape provides tensile pulling through conduit, punch-down tools execute IDC terminations for communications wiring, conduit benders impart specific angular curves to EMT, and knockout punches create precise circular knockouts in steel enclosures.

Adım Adım Çözüm

1

Determine the application of a fish tape.

Fish tape is designed for pulling wire conductors through rigid, IMC, or EMT conduit systems.

Its long, narrow, and flexible spring-steel construction allows it to navigate bends inside enclosed raceways.

2

Determine the application of a punch-down tool.

A punch-down tool is used to terminate structured cabling into punch-down blocks and patch panels.

It pushes the wire into an insulation-displacement contact, piercing the jacket to establish electrical contact, and trims the excess wire end.

3

Determine the application of a conduit bender.

A conduit bender is used to shape metal tubing to fit architectural paths.

The tool applies controlled leverage to form bends (such as 90-degree stubs and offsets) without kinking the conduit wall.

4

Determine the application of a knockout punch.

A knockout punch creates custom-sized circular entry holes in electrical panels.

The mechanical draw mechanism drives a hardened cutter through sheet steel to produce smooth openings for conduit connector fittings.

Anahtar Kavram

Specialized Electrical Installation and Termination Hand Tools

Tahmini Süre:1m 0s

Soru 1086Soru →

A standard automotive piston engine relies on a continuous four-stage operating sequence to convert fuel energy into mechanical power. Arrange the following four strokes in the correct chronological order of operation, starting from the introduction of fresh charge into the cylinder.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

Intake stroke → Compression stroke → Power stroke → Exhaust stroke

The four-stroke engine cycle operates in the strict sequential order of Intake, Compression, Power, and Exhaust. The intake stroke pulls the air-fuel mixture into the cylinder, the compression stroke squeezes the mixture with both valves closed, the power stroke harnesses burning gases to drive the piston down, and the exhaust stroke pushes spent gases out through the open exhaust valve to reset the cylinder.

Adım Adım Çözüm

1

Identify the introductory stroke of the four-stroke cycle

The intake stroke begins the cycle as the descending piston creates low pressure to draw in the air-fuel mixture through the open intake valve.

Combustion requires an air-fuel charge inside the cylinder before any subsequent mechanical operation can take place.

2

Determine the preparation stroke preceding ignition

The compression stroke follows as the rising piston compresses the trapped mixture against closed valves.

Compressing the air-fuel mixture elevates pressure and temperature, maximizing combustion efficiency when ignited.

3

Identify the energy-producing power phase

The power stroke takes place when ignition forces the piston downward to deliver mechanical torque to the crankshaft.

This is the sole stroke in the four-stroke cycle that generates positive mechanical power.

4

Determine the clearing stroke that concludes the cycle

The exhaust stroke completes the sequence as the piston ascends to push spent combustion gases out through the open exhaust valve.

Evacuating spent exhaust gases clears the cylinder volume so a fresh charge can enter on the next intake stroke.

Anahtar Kavram

Four-stroke internal combustion cycle operating sequence (Intake, Compression, Power, Exhaust)

Tahmini Süre:45s

Soru 1087Soru →

An electrical technician connects an inductor and a resistor in series with a direct current ( $\text{DC}$ ) power source and a mechanical switch. Immediately after the switch is closed, which statement accurately describes the initial behavior of the inductor?

It acts as an immediate short circuit with zero initial resistance, allowing maximum current to surge instantly before blocking all current once energized.

It creates a counter-electromotive force (back-EMF) that opposes the sudden change in current, momentarily holding the circuit current at zero.

It completely blocks the electrical current indefinitely because inductive components cannot conduct direct current under any conditions.

It instantly steps up the source voltage to double its rated value across the resistor without drawing any initial energy from the power supply.

Cevabı ve açıklamayı göster

Cevap: It creates a counter-electromotive force (back-EMF) that opposes the sudden change in current, momentarily holding the circuit current at zero.

Cevap

The inductor creates a counter-electromotive force (back-EMF) that opposes the sudden change in current, momentarily holding the circuit current at zero.

Inductors store energy in a magnetic field and oppose any rapid change in electrical current. At the exact moment a DC switch closes, the rate of current change is at its maximum, producing an opposing counter-electromotive force (back-EMF) equal and opposite to the applied source voltage. Consequently, the initial current through the circuit is momentarily zero and rises exponentially over time.

Adım Adım Çözüm

1

Identify the fundamental property of self-inductance upon circuit connection.

An inductor inherently opposes any instantaneous change in the electrical current flowing through its coils (

V_L = L \frac{di}{dt}

).

According to Lenz's Law, when current attempts to rise from zero, the expanding magnetic flux induces an opposing voltage (counter-electromotive force or back-EMF).

2

Determine the initial electrical state at time

t = 0

(immediately upon switch closure).

The induced back-EMF across the inductor equals the full source voltage, meaning initial current

I(0) = 0\text{ A}

and initial resistor voltage drop

V_R = 0\text{ V}

.

Because current cannot change instantaneously through an inductor, it momentarily behaves like an open circuit before current gradually rises exponentially toward its Ohm's Law limit (

I = \frac{V}{R}

).

Anahtar Kavram

Inductor Transient DC Response and Back-EMF

Tahmini Süre:1m 0s

Soru 1088Soru →

An electronics technician is troubleshooting a printed circuit board. The circuit originally consisted of a DC power supply and three resistors: $R_1$ ( $100\ \Omega$ ), $R_2$ ( $150\ \Omega$ ), and $R_3$ ( $300\ \Omega$ ). $R_2$ and $R_3$ are wired in parallel with each other. This parallel pair is connected in series with $R_1$ , and the entire resistor network is connected across the power supply terminals.

To prepare for resistance testing, the technician completely removes the power supply. However, they accidentally leave a solid copper jumper wire connected across the two empty terminals where the power supply was attached.

Without desoldering any components, the technician sets a digital multimeter (DMM) to measure resistance and places the probes directly across the leads of $R_2$ . Assuming all resistors are functioning normally, what resistance reading will the DMM display?

50\ \Omega

100\ \Omega

150\ \Omega

200\ \Omega

Cevabı ve açıklamayı göster

Cevap: $50\ \Omega$

Cevap

The multimeter will display

50\ \Omega

because it measures the equivalent resistance of all parallel paths in the closed loop.

The multimeter measures the equivalent resistance of all parallel paths between its probes. The jumper wire connects

R_1

in parallel with the

R_2

and

R_3

branches. The equivalent resistance of

100\ \Omega

,

150\ \Omega

, and

300\ \Omega

in parallel is

50\ \Omega

.

Adım Adım Çözüm

1

Determine the original circuit topology.

R_1

is in series with the parallel pair of

R_2

and

R_3

.

This establishes the baseline connections before the power supply was removed.

2

Analyze the effect of the jumper wire.

The jumper wire connects the open ends of the circuit, creating a closed loop. It connects the free end of

R_1

directly to the common ground/return path of

R_2

and

R_3

.

This fundamentally changes the topology, placing

R_1

in parallel with

R_2

and

R_3

from the perspective of the components.

3

Identify what the DMM measures when placed across

R_2

.

The DMM measures the total equivalent resistance between the two nodes of

R_2

.

A multimeter cannot isolate a component in a closed circuit; it reads all active parallel paths.

4

Calculate the equivalent resistance of the three parallel branches (

R_1

,

R_2

,

R_3

).

1/R_{eq} = 1/100 + 1/150 + 1/300 = 3/300 + 2/300 + 1/300 = 6/300

.

R_{eq} = 300 / 6 = 50\ \Omega

.

To find the final reading displayed by the meter.

Anahtar Kavram

In-Circuit Resistance Measurement and Component Isolation

Soru 1089Soru →

In a standard four-stroke spark-ignition engine, mechanical actions inside the cylinder occur in a precise sequence to complete one operating cycle. Arrange the following cylinder events in the correct chronological order, starting from the induction of the fresh charge.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence of events is: 1) The intake valve opens as the piston moves downward to draw in the air-fuel mixture; 2) Both valves seal while the piston moves upward to compress the mixture; 3) The spark plug ignites the mixture, driving the piston downward to produce power; 4) The exhaust valve opens as the piston moves upward to expel the burned exhaust gases.

A four-stroke engine operates strictly in the sequence of intake (piston moves down, intake valve open), compression (piston moves up, both valves closed), power (combustion forces piston down, both valves closed), and exhaust (piston moves up, exhaust valve open). Arranging the cylinder events from intake through exhaust accurately reflects the mechanical cycle.

Adım Adım Çözüm

1

Identify the first stroke of the internal combustion operating cycle.

The intake stroke begins at top dead center with the intake valve open and the piston traveling downward, drawing in the air-fuel charge.

An engine must bring a combustible charge into the cylinder before any compression or combustion can take place.

2

Determine the mechanical event following cylinder charging.

The compression stroke follows as both valves close and the piston moves upward toward top dead center, compressing the mixture into a smaller volume.

Compressing the air-fuel mixture increases thermal efficiency and combustion speed prior to ignition.

3

Identify the working phase resulting from mixture ignition.

The power stroke occurs when the spark plug ignites the compressed charge, creating high-pressure expanding gases that push the piston downward.

This is the only stroke in the four-stroke cycle that produces positive mechanical work to rotate the crankshaft.

4

Determine the concluding event of the four-stroke cycle.

The exhaust stroke concludes the cycle as the exhaust valve opens and the rising piston expels the spent combustion byproducts.

Residual burned gases must be cleared from the cylinder volume before a fresh intake stroke can begin.

Anahtar Kavram

The operational sequence and mechanical events of the four-stroke internal combustion engine cycle (intake, compression, power, exhaust).

Tahmini Süre:1m 0s

Soru 1090Soru →

In an automotive fuel system, what is the ideal (stoichiometric) ratio of air to fuel by weight for complete combustion in a standard gasoline engine?

1 part air to 14.7 parts fuel

14.7 parts air to 1 part fuel

4 parts air to 1 part fuel

1 part air to 1 part fuel

Cevabı ve açıklamayı göster

Cevap: 14.7 parts air to 1 part fuel

Cevap

14.7 parts air to 1 part fuel

The stoichiometric air-fuel ratio for gasoline is approximately

14.7:1

by weight. This means 14.7 parts of air are required to completely combust 1 part of fuel with minimal unburned hydrocarbons and carbon monoxide emissions.

Adım Adım Çözüm

1

Identify the definition of stoichiometric air-fuel ratio for standard gasoline.

Stoichiometry is the chemically ideal mass ratio where all fuel is burned with all available oxygen.

Gasoline engines require an exact proportion of atmospheric oxygen to combust hydrocarbons completely without excess air or unburned fuel.

2

Determine the standard mass ratio for gasoline combustion.

14.7 : 1

(14.7 parts air to 1 part fuel by weight).

14.7 pounds/grams of air contain the precise amount of oxygen required to burn 1 pound/gram of gasoline.

Anahtar Kavram

Stoichiometric Air-Fuel Ratio in Gasoline Engines

Tahmini Süre:45s

Soru 1091Soru →

A 10-meter copper conductor has a measured resistance of $0.05\ \Omega$ . A technician needs to fabricate a replacement wire of the exact same length and resistance using an alloy with 4 times the resistivity of copper. How must the cross-sectional area of the replacement wire compare to the original copper wire?

The cross-sectional area must be reduced to 1/4 of the original wire.

The cross-sectional area must remain exactly the same as the original wire.

The cross-sectional area must be 4 times larger than the original wire.

The cross-sectional area must be 16 times larger than the original wire.

Cevabı ve açıklamayı göster

Cevap: The cross-sectional area must be 4 times larger than the original wire.

Cevap

The cross-sectional area must be 4 times larger than the original wire.

Based on the resistance formula

R = \rho \frac{L}{A}

, resistance is directly proportional to resistivity

\rho

and inversely proportional to cross-sectional area

A

. When the replacement wire material has 4 times the resistivity (

\rho' = 4\rho

) but must maintain identical length

L

and total resistance

R

, the cross-sectional area must increase by a factor of 4 (

A' = 4A

) to counterbalance the higher material resistivity.

Adım Adım Çözüm

1

Identify the relationship between electrical resistance, material resistivity, length, and cross-sectional area.

R = \rho \frac{L}{A}

, where

R

is resistance,

\rho

is resistivity,

L

is wire length, and

A

is cross-sectional area.

This formula defines how physical geometry and material properties determine electrical resistance.

2

Rearrange the equation to express cross-sectional area as a function of resistivity, length, and resistance.

A = \frac{\rho L}{R}

Isolating cross-sectional area enables direct evaluation of how area must adjust when resistivity changes while length and resistance remain constant.

3

Substitute the scaled resistivity

\rho' = 4\rho

into the rearranged formula with constant length

L

and constant resistance

R

.

A' = \frac{(4\rho)L}{R} = 4\left(\frac{\rho L}{R}\right) = 4A

Because cross-sectional area is directly proportional to resistivity under constant length and resistance, quadrupling resistivity requires quadrupling the area.

Anahtar Kavram

Resistance and Resistivity Proportionality

Tahmini Süre:1m 0s

Soru 1092Soru →

An electronic circuit uses a standard four-band resistor with the color bands Yellow, Violet, Brown, and Gold reading from left to right. What is the nominal resistance value of this resistor in ohms ( $\Omega$ )?

Cevabı ve açıklamayı göster

Cevap: 470

Cevap

The nominal resistance value is

470\ \Omega

.

In the standard electronic color code system, Yellow represents 4, Violet represents 7, Brown represents a multiplier of 10 (

10^1

), and Gold indicates a tolerance of

\pm 5\%

. Combining the digits gives 47, and multiplying by 10 produces

470\ \Omega

.

Adım Adım Çözüm

1

Decode the first two color bands into the first two digits

Yellow corresponds to 4 and Violet corresponds to 7, giving the base number 47

The first two bands on a four-band resistor represent the first and second significant figures of the resistance value

2

Decode the third band into the decimal multiplier

Brown corresponds to a multiplier of

10^1

(

10

)

The third band indicates the power of ten by which the base number must be multiplied

3

Calculate the total nominal resistance

47 \times 10 = 470\ \Omega

Multiplying the base digits by the multiplier gives the rated nominal resistance in ohms

Anahtar Kavram

Four-band resistor color code decoding

Tahmini Süre:30s

Soru 1093Soru →

During the intake phase of an overhead valve (OHV) internal combustion engine, rotational energy from the camshaft is transferred through a series of internal valve train components to admit the air-fuel mixture. Arrange the following mechanical events in the correct chronological order from initial camshaft lobe contact to the opening of the intake port.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence begins with the camshaft lobe lifting the valve lifter, followed by the lifter driving the pushrod upward, the pushrod pivoting the rocker arm on its fulcrum, the rocker arm depressing the valve stem against spring tension, and finally the valve head separating from the valve seat to unseal the intake port.

In an overhead valve (OHV) engine, the camshaft resides inside the cylinder block. As the camshaft lobe rotates, it lifts the valve lifter (tappet). The lifter pushes the pushrod upward into the cylinder head. The top of the pushrod presses against the outer arm of the rocker arm, causing it to pivot on its shaft or fulcrum. The downward-moving inner tip of the rocker arm pushes against the valve stem tip, compressing the valve spring and moving the valve head off its seat to open the port.

Adım Adım Çözüm

1

Identify the primary driving force in an OHV valve train.

Camshaft lobe rotates and forces the lifter upward.

The camshaft provides the timed rotational input that initiates valve actuation.

2

Trace the motion transfer between the engine block and cylinder head.

Lifter drives the pushrod upward through the block.

In an OHV engine, the camshaft resides in the block, requiring a pushrod to bridge the physical span to the cylinder head.

3

Identify the mechanical motion reversal component.

Pushrod causes the rocker arm to pivot on its fulcrum.

The rocker arm operates as a Class 1 lever to convert the pushrod's upward travel into downward force.

4

Analyze force application against the valve assembly.

Rocker arm compresses the valve spring by pushing the valve stem tip downward.

Downward leverage must overcome the closing pressure exerted by the valve spring.

5

Determine the final fluid dynamic result.

Intake valve head moves off the seat to open the port.

Downward displacement of the valve stem unseats the valve face, opening the pathway for intake charge entry.

Anahtar Kavram

Mechanical force transfer sequence in an OHV valve train

Tahmini Süre:1m 15s

Soru 1094Soru →

In direct-current (DC) parallel circuit analysis, modifying circuit components or introducing faults alters electrical parameters according to fundamental circuit laws. Match each parallel circuit condition or parameter on the left with its correct electrical behavior or outcome on the right.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Adding a branch matches decreasing total equivalent resistance; an open branch matches dropping current to zero only in that branch; branch voltage drop matches remaining identical across all branches; unequal current division matches directing larger current through the smaller resistor.

In parallel circuits: (1) Adding branches decreases equivalent resistance and raises total current; (2) An open in one branch affects only that path; (3) Voltage is equal across all branches; and (4) Branch current is inversely proportional to resistance.

Adım Adım Çözüm

1

Analyze equivalent resistance behavior when adding parallel paths.

R_{\text{eq}}

decreases as branches are added because

\frac{1}{R_{\text{eq}}} = \frac{1}{R_1} + \frac{1}{R_2} + \dots + \frac{1}{R_n}

.

Each added branch provides an additional path for electron flow, reducing overall opposition to current.

2

Evaluate the effect of an open circuit in an isolated parallel branch.

Current ceases in the open branch, while voltage and current across other branches remain steady.

Independent branch connections across common rails preserve full line voltage across unaffected branches.

3

Determine voltage distribution across parallel loads.

Branch voltages are identical (

V_{\text{source}} = V_1 = V_2

).

All parallel elements share the same electrical junctions.

4

Determine current division rules for unequal resistances.

Current flows inversely to resistance (

I_1 = \frac{V}{R_1} > I_2 = \frac{V}{R_2}

when

R_1 < R_2

).

Lower resistance paths draw greater current from the constant branch voltage.

Anahtar Kavram

Parallel Circuit Voltage, Current, Resistance, and Fault Characteristics

Tahmini Süre:1m 15s

Soru 1095Soru →

A communications technician connects an oscilloscope to monitor an unmodulated carrier signal from a transmitter stage. A standard $10\times$ passive attenuation probe is connected to Channel 1, while the oscilloscope input channel remains set to standard $1\times$ scale. On the display, the sinusoidal trace spans $6\text{ vertical divisions}$ from peak to peak with the vertical sensitivity set to $2\text{ V/div}$ . Horizontally, exactly $4\text{ complete cycles}$ span across $8\text{ divisions}$ with the horizontal timebase set to $5\text{ }\mu\text{s/div}$ . What are the true peak-to-peak voltage ( $V_{\text{p-p}}$ ) and frequency ( $f$ ) of the input signal?

12\text{ V}_{\text{p-p}}\text{ and }100\text{ kHz}

120\text{ V}_{\text{p-p}}\text{ and }25\text{ kHz}

120\text{ V}_{\text{p-p}}\text{ and }100\text{ kHz}

60\text{ V}_{\text{p-p}}\text{ and }100\text{ kHz}

Cevabı ve açıklamayı göster

Cevap: $120\text{ V}_{\text{p-p}}\text{ and }100\text{ kHz}$

Cevap

120\text{ V}_{\text{p-p}}\text{ and }100\text{ kHz}

The true peak-to-peak voltage is calculated by multiplying the

6\text{ vertical divisions}

by

2\text{ V/div}

and accounting for the

10\times

probe factor, yielding

120\text{ V}_{\text{p-p}}

. The period for one cycle is

2\text{ divisions} \times 5\text{ }\mu\text{s/div} = 10\text{ }\mu\text{s}

, which gives a frequency of

f = 1 / (10\text{ }\mu\text{s}) = 100\text{ kHz}

.

Adım Adım Çözüm

1

Calculate the displayed peak-to-peak voltage from the vertical graticule divisions and Volts/Div setting

V_{\text{p-p(displayed)}} = 6\text{ divisions} \times 2\text{ V/div} = 12\text{ V}

Each vertical division represents 2 volts on the scope screen.

2

Apply the 10X attenuation probe multiplier to obtain the true input voltage

V_{\text{p-p(true)}} = 12\text{ V} \times 10 = 120\text{ V}_{\text{p-p}}

A 10X attenuation probe divides the circuit voltage by 10 before reaching the scope input, so the observed display value must be multiplied by 10 when the scope is not set to auto-scale.

3

Determine the horizontal division span for one complete cycle

\text{Divisions per cycle} = \frac{8\text{ divisions}}{4\text{ cycles}} = 2\text{ div/cycle}

One full period corresponds to exactly one complete waveform cycle.

4

Calculate the period (T) of the waveform using the horizontal timebase setting

T = 2\text{ div} \times 5\text{ }\mu\text{s/div} = 10\text{ }\mu\text{s} = 10 \times 10^{-6}\text{ s}

Multiplying the division width of one cycle by the timebase gives the duration of one period.

5

Calculate the frequency (f) using the reciprocal of the period

f = \frac{1}{T} = \frac{1}{10 \times 10^{-6}\text{ s}} = 100{}000\text{ Hz} = 100\text{ kHz}

Frequency is the inverse of the period:

f = 1/T

.

Anahtar Kavram

Oscilloscope graticule measurement incorporating 10X probe scaling and period-to-frequency conversion

Tahmini Süre:2m 0s

Soru 1096Soru →

A technician is evaluating an AC ripple voltage on a DC power supply using an oscilloscope. The vertical sensitivity control (Volts/Div) is set to $50\text{ mV/div}$ . If the displayed waveform occupies a total of $6\text{ vertical divisions}$ from its lowest trough to its highest crest, what is the peak voltage ( $V_{\text{pk}}$ ) of the ripple?

300\text{ mV}

150\text{ mV}

25\text{ mV}

1.5\text{ V}

Cevabı ve açıklamayı göster

Cevap: $150\text{ mV}$

Cevap

The peak voltage of the ripple is

150\text{ mV}

.

Multiplying the total vertical deflection (

6\text{ divisions}

) by the vertical sensitivity (

50\text{ mV/div}

) yields a peak-to-peak voltage of

300\text{ mV}

. Peak voltage (

V_{\text{pk}}

) measures the amplitude from the reference centerline to the positive crest, which equals half of the peak-to-peak voltage:

\frac{300\text{ mV}}{2} = 150\text{ mV}

.

Adım Adım Çözüm

1

Calculate the peak-to-peak voltage (

V_{\text{p-p}}

)

V_{\text{p-p}} = 6\text{ divisions} \times 50\text{ mV/div} = 300\text{ mV}

The total vertical span from crest to trough represents the full peak-to-peak voltage.

2

Calculate the peak voltage (

V_{\text{pk}}

)

V_{\text{pk}} = \frac{V_{\text{p-p}}}{2} = \frac{300\text{ mV}}{2} = 150\text{ mV}

Peak voltage is the amplitude measured from the center baseline to either peak, which is half of the peak-to-peak value.

Anahtar Kavram

Determining peak voltage from peak-to-peak vertical graticule measurements on an oscilloscope.

Tahmini Süre:1m 0s

Soru 1097Soru →

When servicing a $120\text{ V}$ alternating current (AC) power supply, a technician replaces a blown glass cartridge fuse with a replacement that has the correct $2\text{ A}$ current rating but a lower voltage rating of $32\text{ V}$ . Why is installing a fuse with this lower voltage rating a serious safety hazard?

The fuse will immediately melt and open under normal continuous load current.

The fuse may sustain an internal electric arc after the element melts, failing to clear the fault current.

The fuse will produce an excessive series voltage drop across its terminals, starving the load of operating voltage.

The fuse will automatically reset and re-energize the circuit before the short circuit is removed.

Cevabı ve açıklamayı göster

Cevap: The fuse may sustain an internal electric arc after the element melts, failing to clear the fault current.

Cevap

The fuse may sustain an internal electric arc after the element melts, failing to clear the fault current.

A fuse's voltage rating specifies its ability to safely suppress and extinguish the electrical arc formed when the internal wire link melts under overcurrent or short-circuit conditions. In a

120\text{ V}

circuit, a

32\text{ V}

rated fuse lacks sufficient dielectric gap and arc-quenching capability, allowing an arc to persist across the open terminals and continue conducting hazardous fault current.

Adım Adım Çözüm

1

Identify the primary electrical function of a fuse's voltage rating.

The voltage rating defines the maximum open-circuit voltage the fuse can safely interrupt without allowing sustained electrical arcing across the blown element gap.

When a fuse blows, the full source voltage appears directly across the open fuse gap.

2

Evaluate the risk of using a

32\text{ V}

rated fuse in a

120\text{ V}

circuit.

Because

120\text{ V}

exceeds the

32\text{ V}

breakdown threshold of the fuse housing and gap, the ionized air can maintain a conductive plasma arc.

Exceeding the voltage rating prevents arc extinction, leading to continuous current conduction, explosive case rupture, and fire hazard.

Anahtar Kavram

Fuse voltage ratings and arc-extinguishing capability

Tahmini Süre:1m 0s

Soru 1098Soru →

A direct current circuit is powered by a $48\text{ V}$ source. The circuit contains a main line with resistor $R_1$ ( $8\text{ }\Omega$ ) which then splits into two parallel branches containing resistor $R_2$ ( $12\text{ }\Omega$ ) and resistor $R_3$ ( $24\text{ }\Omega$ ) respectively. How much electrical power is dissipated specifically by resistor $R_2$ ?

48\text{ W}

72\text{ W}

108\text{ W}

192\text{ W}

Cevabı ve açıklamayı göster

Cevap: $48\text{ W}$

Cevap

The power dissipated specifically by resistor

R_2

is

48\text{ W}

.

To find the power dissipated by

R_2

, we must determine either the specific voltage across it or the specific current through it. First, we find the parallel equivalent resistance of

R_2

and

R_3

:

12\text{ }\Omega

and

24\text{ }\Omega

in parallel give

8\text{ }\Omega

. Adding

R_1

(

8\text{ }\Omega

) gives a total circuit resistance of

16\text{ }\Omega

. The total circuit current is

48\text{ V} / 16\text{ }\Omega = 3\text{ A}

. This

3\text{ A}

current flows through the parallel equivalent resistance (

8\text{ }\Omega

), creating a voltage drop of

24\text{ V}

across the parallel branches. Using this specific voltage for

R_2

, we calculate its power dissipation:

P = V^2 / R = 24^2 / 12 = 576 / 12 = 48\text{ W}

.

Adım Adım Çözüm

1

Calculate the equivalent resistance of the parallel network containing

R_2

and

R_3

.

R_p = \frac{12 \times 24}{12 + 24} = \frac{288}{36} = 8\text{ }\Omega

This condenses the parallel branches into a single equivalent resistance to find the total circuit resistance.

2

Calculate the total resistance of the circuit.

R_{total} = R_1 + R_p = 8 + 8 = 16\text{ }\Omega

Adding the series resistor to the equivalent parallel resistance gives the total resistance.

3

Calculate the total current flowing from the source.

I_{total} = \frac{V_{total}}{R_{total}} = \frac{48}{16} = 3\text{ A}

Ohm's Law allows us to find the total current, which flows entirely through

R_1

.

4

Calculate the voltage drop across the parallel network.

V_p = I_{total} \times R_p = 3 \times 8 = 24\text{ V}

Since components in parallel share the same voltage, this is the voltage across both

R_2

and

R_3

.

5

Calculate the power dissipated by

R_2

.

P_{R2} = \frac{V_p^2}{R_2} = \frac{24^2}{12} = \frac{576}{12} = 48\text{ W}

Using Watt's Law with the specific voltage across

R_2

and its specific resistance gives its power dissipation.

Anahtar Kavram

Calculating power in a series-parallel circuit requires identifying the specific voltage across or current through the individual component, rather than using total circuit values.

Soru 1099Soru →

When preparing to solder a wire splice, what is the proper procedure for applying heat and solder to ensure a sound electrical connection?

Melt the solder directly onto the soldering iron tip and allow it to drip onto the cold wire joint.

Wrap the bare wire joint in insulating vinyl tape before touching it with the heated iron tip.

Heat the wire connection directly with the iron tip, then touch the solder to the heated metal joint.

Apply corrosive acid-core paste across the wire strands before applying the soldering iron.

Cevabı ve açıklamayı göster

Cevap: Heat the wire connection directly with the iron tip, then touch the solder to the heated metal joint.

Cevap

Heat the wire connection directly with the iron tip, then touch the solder to the heated metal joint.

Proper soldering technique requires heating the metal workpiece directly with the iron tip until it reaches the melting temperature of solder. When solder is applied to the heated joint, it melts cleanly and flows evenly across the conductors through capillary action, ensuring low resistance and high mechanical integrity.

Adım Adım Çözüm

1

Clean and tin the soldering iron tip to ensure optimal thermal conductivity.

The soldering iron tip is prepared to transfer heat efficiently to the workpiece.

Oxidation on the tip acts as a thermal barrier, impeding heat transfer.

2

Hold the flat face of the hot iron tip firmly against the joined wire strands.

The metal joint quickly reaches the melting point temperature of the solder alloy.

Molten solder flows naturally toward the source of heat across preheated metal surfaces.

3

Apply rosin-core solder to the heated wire connection on the side opposite the iron tip.

The solder melts cleanly, wetting the conductors and forming a bright, smooth joint.

Allowing the heated workpiece to melt the solder prevents cold joints and premature flux burn-off.

Anahtar Kavram

Proper Soldering Technique and Heat Transfer

Tahmini Süre:45s

Soru 1100Soru →

Match each internal engine component to its primary mechanical function.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Wrist pin matches pivoting inside the piston to secure the small end of the connecting rod; Valve spring matches applying tension to return a poppet valve firmly to its seated, closed position; Cylinder bore matches serving as the smooth cylindrical guide wall containing piston travel; Crankshaft counterweight matches balancing reciprocating and rotational inertia to reduce engine vibration.

Each internal component performs a dedicated role in the mechanical operation of an internal combustion engine: the wrist pin links the piston to the connecting rod, the valve spring forces valves shut after actuation, the cylinder bore guides piston travel, and crankshaft counterweights balance reciprocating forces.

Adım Adım Çözüm

1

Identify the function of the wrist pin

Connects the piston to the connecting rod while allowing rotational pivoting.

The wrist pin fits through the piston pin bore and the rod's small end bushing.

2

Identify the function of the valve spring

Ensures the valve returns to and stays sealed against the valve seat when not forced open by the cam lobe.

Camshafts open valves, while valve springs provide the mechanical force to close them.

3

Identify the function of the cylinder bore

Guides the reciprocating motion of the piston within the engine block.

The piston travels up and down along the honed surface of the cylinder wall.

4

Identify the function of the crankshaft counterweight

Smooths engine operation by offsetting rotating and reciprocating masses.

Counterweights reduce harmonic vibration and stress on main bearings.

Anahtar Kavram

Internal Engine Component Identification and Functions

Tahmini Süre:45s

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram