Tüm alıştırma soruları

5215 soru

Tüm türler5,215 Çoktan seçmeli2,665 Çoklu seçim6 Doğru / Yanlış260 Sayısal512 Eşleştirme930 Sıralama396 Boşluk doldurma397 Kısa cevap49

Soru 1221Soru →

A straight electrical conductor carries a steady direct current vertically through a flat horizontal surface. Which pattern best describes the magnetic field lines formed around the conductor?

Straight magnetic lines that travel parallel alongside the wire in the direction of current flow

Concentric closed circles centered on the wire in planes perpendicular to the conductor

Radial field lines pointing straight outward from the wire due to expanding voltage pressure

Pulsating magnetic loops that appear only when alternating current flows through the wire

Cevabı ve açıklamayı göster

Cevap: Concentric closed circles centered on the wire in planes perpendicular to the conductor

Cevap

Concentric closed circles centered on the wire in planes perpendicular to the conductor

When an electric current passes through a straight conductor, it generates a magnetic field consisting of concentric circular lines of magnetic flux that wrap around the wire in planes perpendicular to the conductor's axis.

Adım Adım Çözüm

Identify the relationship between electric current and magnetic fields.

Every electrical current produces a magnetic field surrounding the conductor.

According to the fundamental principles of electromagnetism (Ampère's Law), moving electrical charges inherently generate a magnetic field.

Determine the geometry of the magnetic field around a straight wire.

The magnetic flux forms continuous concentric circular loops centered on the wire.

The magnetic field lines lie in planes perpendicular to the direction of current flow, following the right-hand rule.

Anahtar Kavram

A straight current-carrying conductor generates a circular magnetic field in planes perpendicular to the direction of the current.

Tahmini Süre:45s

Soru 1222Soru →

Internal combustion engines rely on specialized internal components to transfer power, manage valvetrain motion, dampen rotational stresses, and guide moving assemblies. Match each internal engine component on the left with its primary mechanical role on the right.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Wrist pin matches connecting the piston to the small end of the connecting rod; Harmonic balancer matches absorbing torsional crankshaft vibrations; Valve spring matches maintaining tension to close the valve and keep it seated; Cylinder sleeve matches providing a replaceable, wear-resistant bore surface for piston travel.

Each component is correctly paired with its dedicated operational role in internal engine mechanics: the wrist pin links the piston to the connecting rod, the harmonic balancer dampens crankshaft twisting vibrations, the valve spring forces valves shut against combustion pressure, and the cylinder sleeve provides the friction and wear surface for the piston rings.

Adım Adım Çözüm

Identify the primary function of the wrist pin (gudgeon pin)

Recognize that the wrist pin connects the piston assembly to the connecting rod small end, allowing the necessary pivoting action during the stroke.

Reciprocating motion must be transferred to the connecting rod while it angles during crankshaft rotation.

Determine the role of the harmonic balancer

Identify that the balancer dampens torsional crankshaft vibrations generated by intermittent combustion pressure spikes.

Without a vibration damper, the crankshaft could suffer fatigue failure from natural harmonic frequencies.

Identify the purpose of the valve spring in the cylinder head assembly

Confirm that the spring returns the valve to its closed position and maintains contact between valvetrain components.

Cam lobes only open valves; mechanical spring tension is required to close them securely and prevent valve float.

Analyze the function of a cylinder sleeve (liner)

Match it to providing a durable, replaceable sliding surface inside the cylinder bore.

Liners protect the parent block metal (especially in aluminum blocks) and can be serviced after extensive wear.

Anahtar Kavram

Function and operating principles of internal combustion engine mechanical components

Tahmini Süre:1m 0s

Soru 1223Soru →

In a semiconductor PN junction diode, applying an external reverse-bias voltage causes the depletion region at the junction to widen, which prevents the conduction of majority charge carriers.

Doğru

Yanlış

Cevabı ve açıklamayı göster

Cevap: True

Cevap

True

Applying reverse bias attracts majority carriers away from the PN interface, widening the non-conductive depletion zone and preventing current conduction through the component.

Adım Adım Çözüm

Identify the polarity of the applied external voltage across the diode terminals in reverse bias.

The positive terminal of the power source connects to the n-type cathode, and the negative terminal connects to the p-type anode.

Establishing the reverse-bias electrical configuration determines the direction of the electrostatic forces acting on internal charge carriers.

Determine how internal majority carriers respond to the applied electrostatic field.

Holes in the p-type region are pulled toward the negative terminal, and electrons in the n-type region are pulled toward the positive terminal.

Opposite electrical charges attract, pulling majority carriers away from the central PN boundary.

Evaluate the effect of charge carrier movement on the depletion layer and overall current flow.

The removal of mobile carriers from the junction widens the depletion layer of uncovered ionized atoms, preventing majority carrier flow and allowing only negligible minority leakage current.

The widened depletion layer acts as a high-resistance barrier to electric current, confirming the statement as true.

Anahtar Kavram

PN Junction Biasing and Depletion Layer Dynamics

Tahmini Süre:45s

Soru 1224Soru →

A technician needs to replace a copper feeder cable with an aluminum cable of identical length while maintaining the exact same total electrical resistance. Since aluminum has a higher electrical resistivity than copper ( $\rho_{\text{Al}} > \rho_{\text{Cu}}$ ), which of the following physical characteristics must the replacement aluminum cable have?

A smaller cross-sectional area than the original copper cable

A larger cross-sectional area than the original copper cable

A higher American Wire Gauge (AWG) number than the original copper cable

An applied potential difference inversely proportional to the material resistivity

Cevabı ve açıklamayı göster

Cevap: A larger cross-sectional area than the original copper cable

Cevap

A larger cross-sectional area than the original copper cable

The electrical resistance of a conductor is given by the formula

R = \rho \frac{L}{A}

. When replacing a material with one having a higher resistivity (

\rho

), the cross-sectional area (

A

) must be increased proportionally to maintain the same total resistance (

R

) over an identical length (

L

). Therefore, a thicker conductor with a larger cross-sectional area is required.

Adım Adım Çözüm

Identify the mathematical relationship governing conductor resistance

R = \rho \frac{L}{A}

where

R

is resistance,

\rho

is resistivity,

L

is length, and

A

is cross-sectional area

Electrical resistance depends directly on material resistivity and length, and inversely on cross-sectional area.

Analyze the constraints given in the problem

R_{\text{Al}} = R_{\text{Cu}}

L_{\text{Al}} = L_{\text{Cu}}

, and

\rho_{\text{Al}} > \rho_{\text{Cu}}

The replacement wire must preserve equal total resistance and length despite the change in material.

Determine the required adjustment to cross-sectional area

A_{\text{Al}} = \frac{\rho_{\text{Al}}}{\rho_{\text{Cu}}} \cdot A_{\text{Cu}} > A_{\text{Cu}}

To counterbalance the higher resistivity

\rho_{\text{Al}}

, the denominator

A

must increase proportionally.

Anahtar Kavram

Conductor Resistance and Material Resistivity

Tahmini Süre:1m 0s

Soru 1225Soru →

An electronically controlled automotive air suspension system is designed to maintain a level ride height automatically. When a heavy payload is placed in the cargo area, the rear of the vehicle squats. Arrange the following system operations in the correct chronological order to demonstrate how the active suspension restores the vehicle to its proper trim height.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence starts with the physical compression under load, followed by the sensors sending an electrical signal. The control module then processes this signal and triggers the relay. Next, the compressor activates and valves open, allowing air to finally inflate the bladders and restore ride height.

The active air suspension operates on a standard closed-loop control system. It begins with a physical change (compression), which is converted to an electrical signal by the sensors (input). The control module evaluates this data (processing) and activates the compressor and valves (output). Finally, the system achieves physical correction (inflation) which is verified by the sensors, closing the loop.

Adım Adım Çözüm

Identify the initial mechanical trigger

The added payload causes the rear suspension to compress and squat.

All automated corrections in a feedback loop must begin with a physical deviation from the baseline.

Determine how the physical change is measured

Ride height sensors detect the linkage angle change and send a voltage signal.

The vehicle's computer cannot read physical movement directly; it requires an electrical sensor input.

Identify the processing phase

The suspension control module processes the sensor input.

The computer must evaluate the sensor data against its programmed target height before commanding any action.

Determine the output action

The module activates the air compressor and opens the rear solenoid valves.

Once the module decides correction is needed, it turns on the hardware required to generate and direct pneumatic pressure.

Identify the final resolution and feedback

Pressurized air inflates the springs until the target height is restored.

The physical inflation corrects the squat, and the sensors report the new height back to the module to close the loop.

Anahtar Kavram

Electronic Air Suspension Feedback Loop (Input-Process-Output)

Soru 1226Soru →

An avionics technician is analyzing a direct-current (DC) subassembly with an applied voltage of $36\text{ V}$ across a load resistor rated at $1.8\text{ k}\Omega$ . What is the resistance in ohms and the resulting current in milliamperes? Fill in the blanks below to complete the circuit analysis.

Aşağıdaki boşlukları doldurun

The total resistance of the load is

\Omega

, and the steady current flowing through the circuit is

\text{mA}

Cevabı ve açıklamayı göster

Cevap

The resistance is 1800 Ω and the current is 20 mA.

Converting

1.8\text{ k}\Omega

to base units gives

1800\ \Omega

. Dividing the applied voltage of

36\text{ V}

1800\ \Omega

yields

0.02\text{ A}

, which corresponds to

20\text{ mA}

Adım Adım Çözüm

Convert the load resistance from kilohms (kΩ) to ohms (Ω)

R = 1.8\text{ k}\Omega = 1.8 \times 1000\ \Omega = 1800\ \Omega

Standard electrical calculations using Ohm's Law require base units of ohms, volts, and amperes.

Apply Ohm's Law (

I = \frac{V}{R}

) to calculate the circuit current in amperes

I = \frac{36\text{ V}}{1800\ \Omega} = 0.02\text{ A}

Current is directly proportional to voltage and inversely proportional to resistance.

Convert the current from amperes (A) to milliamperes (mA)

I = 0.02\text{ A} \times 1000\text{ mA/A} = 20\text{ mA}

The required unit for the current blank is milliamperes.

Anahtar Kavram

Ohm's Law (

I = \frac{V}{R}

) and metric prefix conversions (kilo- and milli-).

Tahmini Süre:45s

Soru 1227Soru →

An armory stores a mixture of lithium, alkaline, and nickel-metal hydride (NiMH) batteries. The probability of randomly selecting a lithium battery from the storage is $\frac{2}{5}$ . If there are exactly $48$ lithium batteries in the armory, what is the total number of batteries stored?

72

120

168

240

Cevabı ve açıklamayı göster

Cevap: $120$

Cevap

The total number of batteries stored is 120.

The correct answer is found by setting up the proportion derived from the probability definition: 2/5 = 48/x. Cross-multiplying gives 2x = 240, and dividing by 2 results in 120 total batteries.

Adım Adım Çözüm

Set up the probability formula using the given information.

\text{Probability} = \frac{\text{Number of Lithium}}{\text{Total Batteries}}

, so

\frac{2}{5} = \frac{48}{x}

, where

x

is the total number of batteries.

Single event probability is the ratio of favorable outcomes to the total number of possible outcomes.

Solve the proportion for

x

by cross-multiplying.

2x = 5 \times 48

Cross-multiplying allows us to solve an equation with fractions and isolate the variable terms.

Simplify the equation and isolate

x

2x = 240

, so

x = \frac{240}{2} = 120

Dividing both sides by 2 isolates the variable, revealing the total number of batteries.

Anahtar Kavram

Calculating the total number of outcomes given the probability of a single event and the number of favorable outcomes.

Soru 1228Soru →

An automotive engine exhibits normal oil pressure at idle, but when the engine accelerates to higher RPMs, oil pressure rises excessively beyond manufacturer specifications, threatening to rupture the oil filter gasket. Which component is most likely stuck closed?

Cooling system thermostat

Air-fuel mixture control solenoid

Oil pressure relief valve

Alternator charging regulator

Cevabı ve açıklamayı göster

Cevap: Oil pressure relief valve

Cevap

The oil pressure relief valve is most likely stuck closed.

Because the engine oil pump is a positive displacement pump driven directly by the engine, its output volume rises steadily as RPM increases. The spring-loaded oil pressure relief valve is engineered to unseat when oil gallery pressure reaches a predetermined threshold, safely returning excess oil to the sump. If this valve becomes stuck closed by debris or mechanical binding, the hydraulic pressure continues to climb with engine speed, resulting in dangerously high oil pressure that can rupture the oil filter canister or blow out mating seals.

Adım Adım Çözüm

Analyze the mechanical operating characteristics of the engine oil pump.

Automotive oil pumps are positive displacement pumps whose volume delivery increases directly with crankshaft RPM.

Because engine bearing clearances remain relatively fixed, increased pump flow at high RPM naturally causes hydraulic pressure to rise.

Identify the mechanism responsible for limiting maximum lubrication system pressure.

The oil pressure relief valve uses a calibrated spring that compresses under excessive pressure, opening a bypass passage back to the oil pan or pump inlet.

This bypass action bleeds off excess pressure to prevent damage to the oil filter, oil cooler, seals, and gaskets.

Determine the failure mode that results in excessive pressure at high RPM while maintaining normal pressure at idle.

A relief valve stuck in the closed position allows normal idle pressure but prevents pressure relief at high engine speeds, causing dangerous pressure spikes.

At idle, pump output is low enough that the valve normally remains closed, but as RPM climbs, failure to open causes unrestricted pressure buildup.

Anahtar Kavram

Oil Pressure Relief Valve Operation and Failure Modes

Tahmini Süre:1m 0s

Soru 1229Soru →

In an automotive internal combustion engine, specialized valves and baffles protect the lubrication circuit across varying thermal, operational, and maintenance conditions. Match each lubrication system component with its primary operational purpose.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Anti-drainback valve pairs with retaining lubricant inside the filter to prevent dry starts; Oil filter bypass valve pairs with routing unfiltered oil to galleries during severe filter restriction; Thermostatic oil cooler valve pairs with directing cold oil away from the heat exchanger until operating temperature is reached; Windage tray pairs with preventing the crankshaft from whipping sump oil into aerated foam.

Each component serves a dedicated safeguarding function within the lubrication circuit: the anti-drainback valve prevents gravity siphon after engine shutdown to ensure instant pressure on restart; the filter bypass valve ensures uninterrupted bearing lubrication even if filter media clogs; the thermostatic cooler valve accelerates engine warm-up by bypassing the cooler matrix below operating temperature; and the windage tray prevents crankshaft counterweights from aerating oil in the sump.

Adım Adım Çözüm

Analyze startup protection mechanisms in the oil circuit

Identified the anti-drainback valve as the component that maintains prime in the filter canister upon shutdown.

When an engine is shut down, gravity can drain oil back into the pan unless checked by the one-way anti-drainback diaphragm.

Analyze fail-safe flow paths during filter clogging

Identified the oil filter bypass valve as the pressure-sensitive valve that diverts flow around clogged filter media.

Dirty oil is significantly less damaging to bearings than complete oil starvation.

Analyze thermal management in external lubrication loops

Identified the thermostatic oil cooler valve as the regulator that bypasses the external cooler during cold operating conditions.

Engine oil must reach operating temperature quickly to burn off condensation and establish design flow properties.

Analyze crankcase mechanical dynamics and aeration prevention

Identified the windage tray as the structural baffle isolating the oil sump from crankshaft windage.

Aerated oil contains compressible air bubbles that collapse under journal bearing loads, causing severe metal-to-metal contact.

Anahtar Kavram

Lubrication System Flow Safeguards, Aeration Control, and Thermal Regulation

Tahmini Süre:1m 30s

Soru 1230Soru →

Match each automotive ignition system component with its primary operational function in controlling or delivering the spark.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

The Ignition Control Module switching transistor matches with rapidly opening and closing the primary circuit ground; the ignition coil step-up windings match with transforming low battery voltage into high-voltage pulses via mutual electromagnetic induction; the spark plug ceramic insulator and internal resistor match with preventing high-voltage flashover while suppressing radio frequency interference; and the centrifugal advance mechanism matches with shifting spark timing progressively earlier as engine speed increases.

Each pair correctly matches an essential ignition sub-function: primary switching via the control module transistor, electromagnetic step-up via the coil transformer windings, dielectric insulation and noise suppression via the spark plug ceramic and resistor, and RPM-dependent timing advance via the centrifugal flyweights.

Adım Adım Çözüm

Analyze the primary circuit control component.

Identify that the Ignition Control Module (ICM) switching transistor controls the ground path of the primary winding, interrupting current to trigger magnetic collapse.

Primary switching is essential to generate inductive kickback and high secondary voltage.

Analyze the voltage transformation mechanism.

Identify that the primary and secondary windings in the ignition coil act as a transformer stepping up

12\text{ V}

into

20{}000\text{ to }50{}000\text{ V}

A high voltage is required to ionize the air-fuel gap across the spark plug electrodes.

Analyze spark plug insulation and radio suppression properties.

Identify that the spark plug ceramic body isolates extreme secondary voltage from the engine block, while the built-in resistive core prevents electrical noise across vehicle electronics.

Without proper insulation and resistance, misfires and radio frequency interference occur.

Analyze the engine speed timing adjustment mechanism.

Identify that centrifugal advance mechanisms use rotating weights to advance ignition timing before top dead center (BTDC) at elevated RPM.

Higher engine speeds leave less time per power stroke, requiring the fuel mixture to be ignited earlier.

Anahtar Kavram

Operational roles and electromagnetic principles of automotive ignition system components

Tahmini Süre:1m 30s

Soru 1231Soru →

Match each advanced cooling system diagnostic symptom to its most likely mechanical root cause.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

The correct diagnostic pairings map each specific thermal, pressure, or flow symptom to its corresponding mechanical failure: boil-over after shutdown maps to the pressure cap; cold-start bubbles map to the head gasket; failure to warm up maps to a stuck-open thermostat; and lower hose collapse maps to a missing support spring.

Each symptom strictly correlates with the physics of the cooling system. Pressure drops lower the boiling point (cap failure), combustion leaks introduce non-condensable gases (head gasket), unregulated flow prevents heat accumulation (thermostat), and pump suction physically deforms unsupported hoses (missing spring).

Adım Adım Çözüm

Analyze the boil-over symptom during heat soak.

Identified as a loss of system pressure, pointing directly to a failed radiator cap.

System pressure is required to raise the boiling point of the coolant; without it, the residual heat after shutdown causes boiling.

Evaluate the continuous bubbles upon a cold start.

Identified as combustion gas intrusion, pointing to a failed cylinder head gasket.

Since the engine is cold, boiling is impossible. The bubbles must be external gas (compression/combustion) entering the cooling jacket.

Assess the overcooling condition at highway speeds.

Identified as continuous, unregulated coolant flow to the radiator, pointing to a thermostat stuck open.

The thermostat must restrict flow to build engine heat; if open, highway airflow removes heat faster than the engine generates it.

Examine the mechanical collapse of the lower hose under high RPM.

Identified as a suction-side failure due to a missing internal structural spring.

The water pump pulls coolant from the lower hose. High RPM creates extreme suction that will flatten a hose unless supported by an internal wire spring.

Anahtar Kavram

Cooling System Diagnostics and Fluid Dynamics

Soru 1232Soru →

During a no-start diagnosis on an engine equipped with an electronic ignition system, a technician determines that battery voltage is present at the ignition coil positive terminal while cranking. However, when a test light is connected between the coil negative terminal and engine ground, the light glows steadily and fails to pulse as the engine turns over. Which of the following is the most likely cause of this no-spark condition?

A malfunctioning alternator that is unable to supply charging voltage to the primary circuit during cranking

A failed ignition module or switching circuit that is unable to rapidly open and close the primary ground path

A severely rich air-fuel mixture that shorts out the primary winding before electromagnetic induction can take place

A misaligned camshaft causing spark generation to trigger during the exhaust stroke rather than the compression stroke

Cevabı ve açıklamayı göster

Cevap: A failed ignition module or switching circuit that is unable to rapidly open and close the primary ground path

Cevap

A failed ignition module or switching circuit that is unable to rapidly open and close the primary ground path

For an ignition coil to step up low battery voltage to the high voltage required to bridge the spark plug gap, current flowing through the primary winding must be repeatedly interrupted. When the ignition control module or electronic switching transistor opens the ground circuit, the magnetic field built up in the primary winding instantly collapses across the secondary winding, inducing high voltage. A test light that glows constantly without pulsing indicates that the module or switching circuit is not interrupting the ground path.

Adım Adım Çözüm

Analyze the primary circuit power supply status.

Battery voltage is confirmed at the ignition coil positive terminal, proving the ignition switch and primary feed circuits are functioning properly.

Establishing that power reaches the coil isolates the fault to the coil itself, the secondary circuit, or the primary switching/ground path.

Interpret the test light behavior on the ignition coil negative terminal.

The test light remains constantly lit without pulsing or flashing during engine rotation.

The ignition control module (or switching transistor) must repeatedly ground and open the coil negative terminal to charge and collapse the primary magnetic field.

Determine the operational effect of a continuous, non-switching ground circuit.

Without rapid interruption of primary current, mutual electromagnetic induction cannot occur across the secondary winding.

High secondary voltage (20,000–50,000+ volts) is generated only when the primary magnetic field collapses rapidly across the fine secondary windings.

Anahtar Kavram

Ignition Coil Primary Circuit Switching and Electromagnetic Induction

Alternatif Yöntem

Connecting an automotive digital oscilloscope to the ignition coil negative terminal will display a flat 12-volt baseline rather than the expected switching waveform and 300V to 400V primary flyback spike, confirming the absence of ground switching.

Tahmini Süre:1m 30s

Soru 1233Soru →

As a gasoline engine operates, fresh air and fuel enter the cylinder while the piston travels downward from top dead center. Which phase of the engine cycle is taking place during this action?

Compression stroke

Intake stroke

Power stroke

Exhaust stroke

Cevabı ve açıklamayı göster

Cevap: Intake stroke

Cevap

The intake stroke is the phase where the intake valve opens and downward piston motion draws the air-fuel mixture into the cylinder.

The correct answer describes the intake stroke. During the intake stroke, the intake valve opens while the exhaust valve remains closed. As the piston travels downward from top dead center toward bottom dead center, it creates a low-pressure area inside the cylinder that draws in the fresh air-fuel mixture.

Adım Adım Çözüm

Identify the valve and piston positions described in the question.

The piston is moving downward from top dead center and drawing fresh air and fuel into the cylinder.

Understanding the physical motion and fluid flow defines which stroke is active.

Match these conditions to the corresponding phase of the four-stroke cycle.

The intake stroke is specifically responsible for drawing in the combustible air-fuel charge.

The four strokes occur in sequence: intake (draw in mixture), compression (squeeze mixture), power (combustion expansion), and exhaust (expel spent gases).

Anahtar Kavram

Four-stroke engine operating cycle and the specific function of the intake stroke.

Tahmini Süre:45s

Soru 1234Soru →

An electronics technician needs to safely measure the direct current flowing through a resistor in a DC circuit using a digital multimeter. What is the correct sequence of steps to perform this measurement?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

De-energize the power source

\rightarrow

Configure the multimeter dial and leads for DC current

\rightarrow

Break the circuit at the test point

\rightarrow

Connect the meter in series across the break and restore power.

To measure current safely and accurately, power must first be disconnected. The meter is then configured for DC current (

\text{DCA}

) with the red lead placed in the current jack. Next, the circuit is physically opened at the test point. Finally, the meter probes are inserted in series across the open break and power is restored to take the measurement.

Adım Adım Çözüm

De-energize the circuit power supply.

Voltage and current in the circuit drop to zero.

Eliminates shock hazard and prevents accidental short circuits when modifying wiring.

Select the DC current (

\text{DCA}

) function and insert the red probe into the appropriate ampere/milliampere jack.

The multimeter's internal shunt resistor and sensing circuitry are engaged.

Current measurements require a low-resistance path through the designated current terminal.

Disconnect a lead or component leg to create an open break in the circuit path.

A single physical break is created where total branch current must pass.

An ammeter must be inserted into the conductive path rather than placed across a component.

Attach the meter leads in series across the break, turn on power, and observe the reading.

Current flows through the meter, displaying the measurement.

In a series connection, the full current of that path passes through the meter for accurate measurement.

Anahtar Kavram

Current measurement requires inserting the multimeter in series with the circuit path after de-energizing the circuit and configuring the meter for DC current.

Tahmini Süre:45s

Soru 1235Soru →

Arrange the following procedural steps in the correct chronological order for preparing and terminating a jacketed multi-conductor electrical cable using standard wire preparation tools.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

Cut the cable to length, remove the outer cable jacket, strip individual conductor insulation, and crimp the terminal lugs.

Proper wire preparation follows an outside-in, progressive procedure: cutting the bulk cable cleanly to length, removing the outer protective sheath with a jacket stripper, stripping the insulation from individual conductors using the correct gauge notch, and finally crimping the solderless terminal lugs onto the exposed bare copper.

Adım Adım Çözüm

Size and cut the bulk multi-conductor cable assembly.

A clean, square cable end at the specified total working length.

Cutting to length first establishes the proper dimensions before separating individual sub-components.

Use a cable jacket stripper to score and peel away the outer sheath.

The internal bundle of color-coded insulated wires is exposed without damage.

The outer jacket must be removed before the individual wires inside can be accessed or manipulated.

Select the appropriate AWG notch on a wire stripper and remove insulation from the end of each conductor.

Bare copper wire ends exposed to the exact insertion depth of the terminal barrel.

Stripping conductor insulation exposes the metal required to make an electrical connection while preserving wire strand integrity.

Insert the bare conductor into a terminal lug and compress with a crimping tool.

A mechanically secure and electrically conductive termination.

Crimping permanently secures the terminal to the prepared bare conductor as the final assembly operation.

Anahtar Kavram

Sequential wire preparation workflow using dedicated hand tools

Tahmini Süre:1m 0s

Soru 1236Soru →

A delivery van is driven over a single road depression. The vehicle's suspension compresses and then continues to bounce up and down repeatedly for several seconds before stabilizing, even though the vehicle sits at the correct factory ride height when stationary. What is the most likely cause of this issue?

Fatigued suspension leaf springs that have lost their rated load capacity

A seized steering knuckle ball joint preventing vertical movement

Worn hydraulic dampers that can no longer dissipate spring rebound energy

Severely worn rubber jounce bumpers on the lower control arms

Cevabı ve açıklamayı göster

Cevap: Worn hydraulic dampers that can no longer dissipate spring rebound energy

Cevap

Worn hydraulic dampers that can no longer dissipate spring rebound energy

The primary role of hydraulic dampers (shock absorbers) is to damp spring oscillation by forcing hydraulic fluid through calibrated valves, converting kinetic energy into thermal energy. When dampers wear out, the vehicle maintains correct static ride height because the springs still support the load, but the chassis will bounce repeatedly after hitting a bump because spring rebound is unrestrained.

Adım Adım Çözüm

Analyze the observed symptom of repeated post-impact bouncing against the condition of proper stationary ride height.

Distinguish between weight-bearing components and oscillation-damping components.

Springs support the static weight of the vehicle and dictate ride height, whereas dampers control the rate and duration of spring oscillations.

Evaluate the mechanism of failure that allows continuous oscillation without vehicle sagging.

Identify hydraulic damper degradation as the root cause.

When a damper loses fluid or internal valving resistance, it can no longer convert the spring's kinetic rebound energy into heat, causing prolonged oscillation.

Anahtar Kavram

Functional distinction between suspension springs (load support and ride height) and shock absorbers/dampers (oscillation control)

Tahmini Süre:1m 0s

Soru 1237Soru →

A straight copper conductor moved parallel to the lines of a uniform magnetic field develops an induced electromotive force across its terminals.

Doğru

Yanlış

Cevabı ve açıklamayı göster

Cevap: False

Cevap

False

The statement is false because electromagnetic induction requires a conductor to cut across magnetic lines of force. When the direction of motion is parallel to the magnetic flux lines, zero flux is cut, resulting in zero induced electromotive force.

Adım Adım Çözüm

Identify the physical requirement for motional electromagnetic induction in a conductor.

Electromagnetic induction occurs when a conductor moves across magnetic lines of force, represented by the relationship

E = B \cdot l \cdot v \cdot \sin\theta

A magnetic force acts on charge carriers only when there is a component of velocity perpendicular to the magnetic field vector.

Determine the angle of motion relative to the magnetic field lines.

Since the conductor moves parallel to the magnetic field lines, the angle

\theta = 0^\circ

, and

\sin(0^\circ) = 0

Parallel motion means the conductor cuts zero magnetic flux lines per unit of time.

Calculate the resulting induced electromotive force (EMF).

The induced voltage is zero, confirming the statement is false.

Without cutting magnetic flux lines, no potential difference can be established between the conductor ends.

Anahtar Kavram

Motional electromagnetic induction requires cutting across magnetic flux lines; movement parallel to magnetic field lines produces zero induced voltage.

Tahmini Süre:45s

Soru 1238Soru →

In a standard fuel-injected automotive engine, ambient air must pass through several induction components before reaching the combustion chamber. In what sequential order does incoming air travel through these intake components from the atmosphere to the engine cylinder?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence of intake airflow from the atmosphere into the engine is: Air filter element, Mass Air Flow (MAF) sensor, Throttle body valve, Intake manifold plenum and runners, and Intake valve.

Air drawn by engine vacuum enters through the air filter housing where contaminants are removed. The clean air passes across the Mass Air Flow sensor to determine fuel metering requirements, through the throttle body plate that regulates engine speed, into the intake manifold runners for even cylinder distribution, and finally past the mechanically timed intake valve into the combustion chamber.

Adım Adım Çözüm

Identify the initial point of entry for external ambient air.

The air filter element cleans atmospheric air of particulates before it enters the intake tract.

Filtering must occur upstream of all intake sensors and moving components to prevent mechanical damage and contamination.

Determine where air mass is measured.

The Mass Air Flow (MAF) sensor measures the mass and density of the incoming filtered air.

The engine control module requires accurate air mass readings before the air is throttled or distributed.

Locate the primary airflow control mechanism.

The throttle body valve controls how much air passes deeper into the induction system.

The throttle plate regulates intake manifold vacuum and engine output based on operator demand.

Trace the path through the air distribution network.

The intake manifold plenum and runners route the regulated airflow toward individual cylinder ports.

The manifold evenly distributes the charge to each cylinder head intake port.

Identify the final gate into the combustion chamber.

The intake valve opens to allow the air charge into the cylinder bore.

The intake valve provides timed mechanical sealing and opening directly at the cylinder head.

Anahtar Kavram

Sequential path of induction airflow through automotive engine intake components

Tahmini Süre:1m 0s

Soru 1239Soru →

When a driver turns the steering wheel in a vehicle equipped with a rack-and-pinion system, mechanical force travels through a series of components to turn the wheels. What is the correct sequence of force transfer, starting from the driver's steering input down to the front wheel assemblies?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

Steering column and intermediate shaft → Pinion gear → Toothed steering rack → Inner and outer tie rods

Steering input begins when the driver rotates the steering wheel. This turns the steering column shaft, which rotates the pinion gear. The pinion gear meshes with the toothed rack to produce side-to-side linear motion, which finally pushes and pulls the inner and outer tie rods to pivot the wheels.

Adım Adım Çözüm

Identify the component directly connected to the steering wheel.

The steering column and intermediate shaft receive the driver's initial rotational motion.

Rotational force enters the steering system through the column shaft before reaching any gear assemblies.

Trace the rotational force into the steering gear assembly.

The shaft rotates the pinion gear inside the steering gear housing.

The pinion gear is fixed to the lower end of the steering shaft and serves as the driving gear.

Identify the conversion from rotational to linear motion.

The meshing teeth force the horizontal steering rack to slide laterally left or right.

The rack and pinion interface transforms rotary torque into linear push-pull movement.

Trace the movement from the rack to the wheel hubs.

The sliding rack pushes or pulls the inner and outer tie rods connected to the steering knuckles.

Tie rods serve as the final linkage connecting the moving rack to the wheels.

Anahtar Kavram

Mechanical force transfer sequence in a rack-and-pinion steering assembly

Tahmini Süre:45s

Soru 1240Soru →

An automotive technician observes dense black smoke exiting a vehicle's tailpipe along with a strong odor of unburned gasoline. Which engine operating condition is the most likely cause of this exhaust symptom?

Lean air-fuel mixture

Rich air-fuel mixture

Stuck-closed engine thermostat

Weak alternator output

Cevabı ve açıklamayı göster

Cevap: Rich air-fuel mixture

Cevap

Rich air-fuel mixture

A rich air-fuel mixture occurs when too much gasoline is delivered into the combustion chambers relative to the intake air. Because there is not enough oxygen to burn all of the fuel completely, unburned hydrocarbons and carbon soot pass through the exhaust system, creating dense black smoke and a distinct fuel odor at the tailpipe.

Adım Adım Çözüm

Analyze the tailpipe exhaust symptom

Dense black smoke and the odor of unburned gasoline indicate incomplete fuel combustion.

Exhaust smoke color provides key diagnostic clues about combustion conditions.

Determine the combustion chemistry cause

Excessive fuel entering the cylinders relative to available air creates soot (carbon) and raw fuel vapors.

When an engine runs rich, there is insufficient oxygen to fully combust all hydrocarbons into carbon dioxide and water vapor.

Anahtar Kavram

Tailpipe Exhaust Smoke Diagnosis and Air-Fuel Mixture

Tahmini Süre:45s

ÖncekiSayfa 62 / 261Sonraki

Tüm alıştırma soruları

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Alternatif Yöntem

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm