Tüm alıştırma soruları

Soru 941Soru →

A technician connects an alternating current (AC) power source to the primary winding of an iron-core transformer to power a low-voltage circuit. Which of the following statements correctly explains how electrical energy is transferred from the primary winding to the secondary winding?

The primary coil stores electrical energy in an electrostatic field between the windings, which discharges periodically into the secondary circuit.

The alternating current in the primary winding creates a dynamic magnetic field that cuts across the secondary winding, inducing an alternating voltage through mutual induction.

A steady direct current magnetizes the iron core, enabling electrons to physically conduct through the core material into the secondary winding.

High primary voltage forces electrons to ionize the insulation and jump across the air gap directly into the secondary conductors.

Cevabı ve açıklamayı göster

Cevap: The alternating current in the primary winding creates a dynamic magnetic field that cuts across the secondary winding, inducing an alternating voltage through mutual induction.

Cevap

The alternating current in the primary winding creates a dynamic magnetic field that cuts across the secondary winding, inducing an alternating voltage through mutual induction.

Energy transfer in a transformer occurs via mutual induction. When alternating current flows through the primary winding, it produces a continuously changing magnetic flux. This flux travels through the ferromagnetic core and links with the secondary winding, inducing an alternating voltage across the secondary terminals according to Faraday's Law of Induction without requiring any direct electrical connection.

Adım Adım Çözüm

1

Identify the electrical input supplied to the primary winding

Alternating current (AC) flows through the primary coil, providing a continuously varying current over time.

A time-varying current is necessary to generate a continuously changing magnetic field.

2

Analyze the behavior of the magnetic field generated within the core

The changing primary current creates an expanding and collapsing magnetic flux that circulates through the ferromagnetic core.

According to Ampere's Law and the principles of electromagnetism, electric current passing through a wound coil establishes a concentrated magnetic field proportional to the current.

3

Determine the mechanism producing electrical energy in the secondary circuit

The moving magnetic flux lines cut through the secondary coil windings, generating an induced electromotive force (voltage) across its terminals.

Faraday's Law of Electromagnetic Induction dictates that a changing magnetic flux passing through a closed loop induces a voltage without any direct physical electrical connection between the coils.

Anahtar Kavram

Mutual Induction in Transformers

Tahmini Süre:1m 0s

Soru 942Soru →

In electronic power and communication systems, various inductor and transformer configurations serve specialized functions. Match each inductive component on the left with its primary operational characteristic on the right.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

RF Choke matches with presenting high opposition to high-frequency AC signals while allowing DC to pass; Isolation Transformer matches with providing a 1:1 turns ratio to electrically decouple circuits for safety; Air-Core Inductor matches with eliminating magnetic core losses at ultra-high frequencies; Step-Up Transformer matches with increasing alternating voltage while decreasing output current proportionally.

Each inductive device is matched according to its fundamental electromagnetic function: an RF choke blocks AC via inductive reactance while passing DC; an isolation transformer provides 1:1 galvanic isolation; an air-core inductor eliminates ferromagnetic core losses at high frequencies; and a step-up transformer increases voltage while proportionally reducing current.

Adım Adım Çözüm

1

Identify the primary behavior of an RF choke

Recognized as a high-frequency AC blocking inductor that freely passes DC.

Inductive reactance (

X_L = 2\pi f L

) increases directly with frequency, creating significant impedance at radio frequencies.

2

Identify the function of an isolation transformer

Recognized as a 1:1 turns ratio transformer used for safety and ground-loop isolation.

Equal winding counts maintain input voltage on the secondary side while eliminating direct conductive connections.

3

Determine the main design advantage of an air-core inductor

Recognized as eliminating ferromagnetic core losses.

Without a solid iron or magnetic core, there are zero eddy currents or magnetic hysteresis losses at high frequencies.

4

Evaluate the voltage and current relationship of a step-up transformer

Recognized as increasing voltage while decreasing current proportionally.

Due to the principle of power conservation (

V_p I_p \approx V_s I_s

), increasing secondary voltage requires a corresponding drop in secondary current.

Anahtar Kavram

Operational characteristics and applications of inductors and transformers, including frequency-dependent choke behavior, core losses, galvanic isolation, and turns ratio power relationships.

Tahmini Süre:1m 0s

Soru 943Soru →

An aircraft landing light is connected to a $28\text{ V}$ DC bus and draws a current of $4\text{ A}$ . What is the total electrical power consumed by the light?

7\text{ W}

32\text{ W}

112\text{ W}

1120\text{ W}

Cevabı ve açıklamayı göster

Cevap: $112\text{ W}$

Cevap

112\text{ W}

According to Watt's Law, electrical power (

P

) is equal to the product of voltage (

V

) and current (

I

). Multiplying

28\text{ V}

by

4\text{ A}

yields

112\text{ W}

.

Adım Adım Çözüm

1

Identify the given electrical values from the circuit

Voltage

V = 28\text{ V}

, Current

I = 4\text{ A}

These are the two known parameters required to calculate power directly.

2

Select Watt's Law power formula that relates voltage, current, and power

P = V \times I

Electrical power in watts is equal to electromotive force in volts multiplied by current in amperes.

3

Calculate the total power dissipation

P = 28\text{ V} \times 4\text{ A} = 112\text{ W}

Multiplying

28

by

4

gives the power consumption in watts.

Anahtar Kavram

Electrical Power Calculation using Watt's Law (

P = V \times I

)

Tahmini Süre:45s

Soru 944Soru →

In direct-current (DC) circuits, understanding the fundamental definitions, units, and directional models of electric charge is essential for troubleshooting. Match each electrical current concept on the left with its correct physical description or definition on the right.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Electron Flow Theory pairs with the physical drift of negative charge carriers from negative to positive; Conventional Current Theory pairs with the classical convention of positive charge moving from positive to negative; Electric Current Rate (

1\text{ A}

) pairs with one coulomb passing per second; and Total Electric Charge (

1\text{ C}

) pairs with the quantity of charge from

6.24 \times 10^{18}

electrons.

Each concept accurately reflects its physical and scientific definition: electron flow describes negative carriers moving negative-to-positive, conventional flow describes positive-to-negative modeling, an ampere defines charge rate per second, and a coulomb defines total accumulated electron charge.

Adım Adım Çözüm

1

Differentiate between the two current flow directional models

Electron flow represents actual negative charge carriers moving from negative to positive terminals, while conventional flow designates positive charge moving from positive to negative terminals.

Clear separation of physical electron movement from historical circuit conventions prevents directional polarity errors.

2

Distinguish rate of flow (current) from static quantity of charge

Current measured in amperes (

1\text{ A} = 1\text{ C/s}

) represents the rate of charge transfer, whereas charge measured in coulombs (

1\text{ C} \approx 6.24 \times 10^{18}\text{ electrons}

) represents the accumulated charge quantity.

Differentiating rate (

I = Q/t

) from total charge (

Q

) is fundamental to quantitative circuit analysis.

3

Verify all four concept-to-definition pairings

Each electrical concept on the left uniquely and unambiguously aligns with its physical definition on the right.

Ensures complete matching accuracy without conceptual overlap.

Anahtar Kavram

Electric current is the time rate of charge flow through a conductor (

I = Q/t

), where electrons physically drift from negative to positive potentials while conventional current is modeled from positive to negative.

Tahmini Süre:45s

Soru 945Soru →

An electronics technician is sorting materials for a repair job based on their electrical properties. Arrange the following materials in order from the highest electrical conductivity (best conductor) to the lowest electrical conductivity (best insulator).

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

Copper, Germanium, Rubber

Metals like copper have a high concentration of free electrons, making them excellent conductors. Group IV elements such as germanium act as semiconductors with intermediate conductivity. Non-metallic compounds like rubber hold their electrons tightly in covalent structures, acting as insulators with the lowest conductivity.

Adım Adım Çözüm

1

Identify the conductor among the materials

Copper is identified as a conductor with high electrical conductivity.

Conductors have loosely bound valence electrons that move freely under an applied voltage.

2

Identify the semiconductor among the materials

Germanium is identified as a semiconductor with moderate electrical conductivity.

Semiconductors have four valence electrons and exhibit conductivity between conductors and insulators.

3

Identify the insulator among the materials

Rubber is identified as an insulator with extremely low electrical conductivity.

Insulators hold valence electrons tightly, offering very high resistance to current flow.

4

Sequence the materials from highest to lowest electrical conductivity

Copper (conductor)

\rightarrow

Germanium (semiconductor)

\rightarrow

Rubber (insulator)

The ranking follows the natural continuum of charge carrier availability in solids.

Anahtar Kavram

Classification and relative electrical conductivity of conductors, semiconductors, and insulators.

Tahmini Süre:45s

Soru 946Soru →

An electronics technician is testing an aircraft panel indicator circuit. When connected to a $24\text{ V}$ DC power supply, the circuit draws a steady current of $4\text{ A}$ . What is the resistance of the circuit, and what current will flow if the supply voltage is reduced to $12\text{ V}$ ?

Aşağıdaki boşlukları doldurun

According to Ohm's Law, the resistance of the circuit is

\Omega

, and when the voltage is decreased to

12\text{ V}

, the new current drawn by the circuit is

\text{A}

.

Cevabı ve açıklamayı göster

Cevap

The resistance of the circuit is

6\ \Omega

and the current under the reduced voltage is

2\text{ A}

.

Applying Ohm's Law, the resistance is found by dividing the initial voltage by the initial current (

R = \frac{24\text{ V}}{4\text{ A}} = 6\ \Omega

). Keeping this resistance constant, halving the voltage to

12\text{ V}

results in half the current (

I = \frac{12\text{ V}}{6\ \Omega} = 2\text{ A}

).

Adım Adım Çözüm

1

Calculate the circuit resistance using Ohm's Law with the initial parameters (

V_1 = 24\text{ V}

,

I_1 = 4\text{ A}

).

R = \frac{V_1}{I_1} = \frac{24\text{ V}}{4\text{ A}} = 6\ \Omega

Ohm's Law states that resistance equals voltage divided by current (

R = \frac{V}{I}

).

2

Determine the new current when the voltage is adjusted to

V_2 = 12\text{ V}

across the constant

6\ \Omega

resistance.

I_2 = \frac{V_2}{R} = \frac{12\text{ V}}{6\ \Omega} = 2\text{ A}

Current is directly proportional to voltage for a fixed resistance (

I = \frac{V}{R}

).

Anahtar Kavram

Ohm's Law expresses the fundamental relationship among voltage, current, and resistance:

V = I \times R

,

I = \frac{V}{R}

, and

R = \frac{V}{I}

.

Tahmini Süre:45s

Soru 947Soru →

An electronics technician is tasked with creating an insulated, moisture-resistant in-line crimp splice on a stranded copper wire using manual electrical hand tools. In what sequential order should the following steps be executed to ensure proper mechanical strength and electrical integrity?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence is: (1) Trim the damaged conductor ends square using diagonal cutting pliers, (2) Slide the heat-shrink tubing onto one lead away from the joint, (3) Strip the insulation using the matched wire stripper notch, (4) Insert the wire into the butt connector and compress with the ratcheting crimper, and (5) Center the tubing over the joint and shrink with a heat gun.

Executing the sequence by trimming, staging heat-shrink tubing, stripping with sized stripper notches, crimping with a calibrated ratcheting tool, and finally heat-sealing adheres strictly to standard electrical assembly protocols, ensuring both conductor integrity and permanent insulation.

Adım Adım Çözüm

1

Cut and square off the wire conductors using diagonal cutting pliers.

Clean, perpendicular wire ends ready for stripping and connector seating.

Jagged or frayed wire ends prevent uniform insertion into crimp barrels and can puncture insulation.

2

Place heat-shrink sleeving over one wire harness branch before completing the splice.

Protective sleeving is staged on the wire harness.

Closed-loop in-line splices cannot accommodate non-split heat-shrink tubing once the terminal barrel is crimped to both sides.

3

Strip the manufacturer-specified strip length using the exact AWG-marked die of precision wire strippers.

Exposed copper strands with zero severed, nicked, or displaced wire strands.

Using an oversized notch fails to strip cleanly, while an undersized notch severs outer strands and reduces current-carrying capacity.

4

Seat the stripped conductors into the butt connector barrel and cycle the ratcheting crimper until the mechanism releases.

A gas-tight, cold-welded mechanical and electrical connection with high tensile pull-out strength.

Ratcheting crimpers enforce full compression of the terminal barrel without under-crimping or over-fracturing the metal sleeve.

5

Position the heat-shrink tubing symmetrically over the metal barrel and apply hot air evenly.

A fully insulated, moisture-proof, strain-relieved wire connection.

Even heating prevents scorching the wire insulation while ensuring the internal hot-melt adhesive flows to seal out moisture.

Anahtar Kavram

Standard sequential operation of electrical hand tools for wire preparation, mechanical termination, and splice insulation.

Tahmini Süre:1m 30s

Soru 948Soru →

An electronics technician selects a four-band carbon-film resistor with the color sequence Brown, Green, Red, and Gold. What is the nominal resistance and tolerance of this resistor?

150\ \Omega\text{ with } \pm 5\%\text{ tolerance}

1.5\text{ k}\Omega\text{ with } \pm 5\%\text{ tolerance}

1.5\text{ k}\Omega\text{ with } \pm 10\%\text{ tolerance}

15\text{ k}\Omega\text{ with } \pm 5\%\text{ tolerance}

Cevabı ve açıklamayı göster

Cevap: $1.5\text{ k}\Omega\text{ with } \pm 5\%\text{ tolerance}$

Cevap

1.5\text{ k}\Omega\text{ with } \pm 5\%\text{ tolerance}

(

1,500\ \Omega \pm 5\%

)

Decoding the four color bands in standard order gives: Brown = 1 (first digit), Green = 5 (second digit), Red =

10^2

or

\times 100

(multiplier), and Gold =

\pm 5\%

(tolerance). Calculating

15 \times 100\ \Omega

yields

1,500\ \Omega

, which converts to

1.5\text{ k}\Omega

with a

\pm 5\%

tolerance.

Adım Adım Çözüm

1

Identify the first two significant digit color bands.

Brown represents the digit 1, and Green represents the digit 5, forming the number 15.

In a standard four-band resistor, the first two bands establish the base significant figures.

2

Determine the multiplier from the third band.

Red represents a multiplier of

10^2

(

100

).

The third band indicates the power of ten by which the significant digits are multiplied.

3

Calculate the nominal resistance value.

15 \times 100 = 1,500\ \Omega = 1.5\text{ k}\Omega

.

Multiplying the base digits by the multiplier yields the total nominal resistance.

4

Identify the tolerance from the fourth band.

Gold indicates a tolerance of

\pm 5\%

.

The fourth band specifies the acceptable manufacturing variation percentage.

Anahtar Kavram

Four-band resistor color code decoding and tolerance identification

Tahmini Süre:35s

Soru 949Soru →

In electrical and electronic control systems, electromechanical relays and multi-contact switches rely on specialized internal components and contact configurations to direct current and automate circuits. Match each switch or relay component to its primary mechanical or electrical operational function.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Common (COM) Terminal matches the shared conductive connection point that routes current to selectable paths; Relay Armature matches the movable ferromagnetic component attracted by magnetic flux; Normally Closed (NC) Contacts match the contact pair that maintains a closed conductive path in the resting de-energized state and opens when actuated; Relay Solenoid Coil matches the insulated wire winding that produces an electromagnetic pulling force.

Each component corresponds directly to its mechanical or electrical role in relay operation: the Common terminal serves as the shared current pathway, the armature provides the physical motion via magnetic attraction, Normally Closed contacts provide resting continuity, and the solenoid coil generates the magnetic force from the control circuit.

Adım Adım Çözüm

1

Identify the function of the Common (COM) Terminal

Matched with the shared conductive connection point that routes current to one of multiple selectable contact paths.

In single-pole double-throw (SPDT) configurations and standard relays, the COM terminal is the central node connected internally to either the NO or NC contact.

2

Identify the function of the Relay Armature

Matched with the movable ferromagnetic component that physically transfers motion to open or close contacts.

The armature is the mechanical piece of iron that pivots when drawn toward the core by electromagnetic attraction.

3

Identify the function of the Normally Closed (NC) Contacts

Matched with the contact pair that maintains continuity during the resting de-energized state and opens upon actuation.

'Normally' designates the shelf or unpowered state, meaning NC contacts conduct electricity until an active force separates them.

4

Identify the function of the Relay Solenoid Coil

Matched with the insulated wire winding that produces an electromagnetic pulling force when control current flows through it.

The coil converts electrical input energy into a magnetic field via electromagnetic induction to drive the switching mechanism.

Anahtar Kavram

Electromechanical Relay Structure and Contact Nomenclature

Alternatif Yöntem

Categorize each item first by its physical domain: identify the electrical input terminal (COM), the mechanical moving element (Armature), the resting electrical state (NC contacts), and the electromagnetic actuator (Coil).

Tahmini Süre:1m 0s

Soru 950Soru →

A light-emitting diode (LED) produces light when it is connected in a reverse-bias orientation within a direct current (DC) circuit.

Doğru

Yanlış

Cevabı ve açıklamayı göster

Cevap: False

Cevap

False. A light-emitting diode (LED) produces light only when forward-biased; in a reverse-bias configuration, it blocks current flow and stays dark.

The statement is false because a light-emitting diode (LED) must be forward-biased (anode connected to the positive potential and cathode connected to the negative potential) to conduct electrical current and release energy in the form of light. In a reverse-bias orientation, the diode blocks current and produces no light.

Adım Adım Çözüm

1

Identify the operating requirement of a semiconductor diode and LED.

Diodes conduct electric current in only one direction (forward bias) and block current in the opposite direction (reverse bias).

An LED functions as a standard PN-junction diode with the specialized property of emitting light when electric current conducts through it.

2

Determine the state of the LED in a reverse-bias orientation.

Under reverse bias, the internal depletion region widens, preventing current flow across the junction.

Because no charge carriers cross the junction under reverse bias, no electron-hole recombination occurs, preventing any light emission.

Anahtar Kavram

Light-emitting diodes (LEDs) require forward biasing (anode connected to a higher positive potential than cathode) to conduct current and emit light.

Tahmini Süre:45s

Soru 951Soru →

A technician performs electrical diagnostic checks on various direct-current (DC) circuit components. Match each multimeter measurement or symptom to the correct circuit condition or fault.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Match the open coil to infinite resistance, intact fuse to 0 V drop, shorted load to 0 V with high current surge / blown fuse, and high-resistance contact fault to elevated closed-switch resistance.

Each diagnostic measurement corresponds to a fundamental circuit state: infinite coil resistance reflects an open circuit; zero volts across an intact fuse demonstrates normal low-resistance conduction; zero volts with blown protection indicates a short circuit; and elevated resistance across closed switch contacts indicates a high-resistance contact fault.

Adım Adım Çözüm

1

Analyze the isolated coil resistance test reading

An infinite resistance (O.L.) measurement signifies an internal discontinuity or open circuit.

Current cannot pass through a severed conductor, resulting in infinite measured resistance.

2

Evaluate the in-circuit voltage drop across the closed fuse

A 0 V drop across an intact conducting fuse indicates normal low-resistance operation.

According to Ohm's law (

V = I \times R

), a conductor with negligible resistance produces virtually no voltage drop.

3

Identify the fault causing 0 V across a load with blown overcurrent protection

A short circuit parallel to or across the load bypasses normal resistance and draws excessive current.

Zero branch resistance eliminates voltage drop across the parallel terminals while causing current to surge past the fuse rating.

4

Interpret the elevated resistance reading across closed switch contacts

A reading of

180\,\Omega

represents an abnormal high-resistance fault.

Clean, closed mechanical contacts should read less than

1\,\Omega

; oxidation and pitting insert unwanted resistance into the path.

Anahtar Kavram

Circuit Fault Diagnosis and Multimeter Interpretation

Tahmini Süre:1m 15s

Soru 952Soru →

A technician needs to test a household appliance heating element for continuity and resistance using a digital multimeter. What is the correct chronological sequence of steps to perform this measurement safely and accurately?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct chronological sequence is: first disconnect the appliance power supply, second disconnect at least one wire lead to isolate the heating element, third insert the test leads and set the multimeter dial to resistance, fourth touch probe tips together to verify meter zeroing and lead continuity, and fifth place the probe tips across the heating element terminals to read the resistance value.

The correct sequence follows standard electronics testing protocol: power must always be disconnected first for safety, the component must be isolated to prevent parallel loop paths from skewing readings, the meter must be properly set up, test leads must be shorted to verify zero calibration, and finally the probes are applied to measure the isolated component.

Adım Adım Çözüm

1

Disconnect electrical power from the appliance.

The appliance is completely de-energized.

Multimeters use an internal battery to pass a known current for resistance measurement; external voltage can blow the meter fuse, destroy internal circuitry, or cause electric shock.

2

Detach at least one wire connection from the heating element.

The component is electrically isolated from surrounding circuitry.

Leaving both ends connected allows current to pass through parallel components, resulting in a false, lower resistance reading.

3

Plug black lead into COM, red lead into

\Omega

, and select the resistance range on the meter dial.

The digital multimeter is configured for resistance mode.

Proper jack selection and mode switching ensure the meter applies its internal reference voltage and measures current correctly.

4

Touch the test probe tips together.

The display indicates close to

0\ \Omega

.

This confirms good test lead integrity, proper meter zero reference, and active battery power.

5

Contact the probe tips to the two heating element terminals.

The true component resistance is displayed.

The meter measures the voltage drop across the isolated resistance element to calculate and display its value.

Anahtar Kavram

Safe and accurate multimeter resistance and continuity measurements require complete circuit de-energization, component isolation, proper lead/meter configuration, calibration verification, and direct terminal contact.

Tahmini Süre:1m 15s

Soru 953Soru →

An automated assembly fixture uses an industrial direct current (DC) solenoid valve to actuate a pneumatic clamp. The solenoid coil has an internal resistance of $600\text{ }\Omega$ and requires a steady current of $35\text{ mA}$ to operate reliably. What DC voltage must the power supply deliver to the solenoid valve?

17.1\text{ V}

2.1\text{ V}

21\text{ V}

21,000\text{ V}

Cevabı ve açıklamayı göster

Cevap: $21\text{ V}$

Cevap

21\text{ V}

According to Ohm's Law, voltage is calculated by multiplying current by resistance (

V = I \times R

). Converting the current from milliamperes to amperes gives

35\text{ mA} = 0.035\text{ A}

. Multiplying

0.035\text{ A} \times 600\text{ }\Omega

results in

21\text{ V}

.

Adım Adım Çözüm

1

Convert the operating current from milliamperes (

\text{mA}

) to base amperes (

\text{A}

).

35\text{ mA} = \frac{35}{1,000}\text{ A} = 0.035\text{ A}

Ohm's Law calculations require electrical quantities in standard SI base units.

2

Apply Ohm's Law (

V = I \times R

) to find the required supply voltage.

V = 0.035\text{ A} \times 600\text{ }\Omega = 21\text{ V}

Voltage equals the product of current and resistance.

Anahtar Kavram

Ohm's Law (

V = I \times R

) with metric prefix conversion

Tahmini Süre:1m 0s

Soru 954Soru →

A $12\text{ V}$ direct-current (DC) circuit consists of a power source, a single-pole toggle switch, and an indicator lamp wired in series. When the switch is flipped to the ON (closed) position, the lamp fails to illuminate. A technician connects a digital multimeter across the two terminals of the closed switch and reads $12\text{ V}$ . Which of the following faults is indicated by this measurement?

The indicator lamp has a short circuit across its filament.

The circuit is operating normally and drawing maximum rated current.

The switch contacts have failed open internally.

The indicator lamp filament is burned open.

Cevabı ve açıklamayı göster

Cevap: The switch contacts have failed open internally.

Cevap

The switch contacts have failed open internally.

In a series circuit, a closed switch should exhibit continuity (

0\ \Omega

) and produce a

0\text{ V}

drop. When a digital multimeter measures the entire source voltage (

12\text{ V}

) across a switch in the ON position, it proves that the switch contacts have failed to close electrically, acting as an open circuit that drops the entire available potential.

Adım Adım Çözüm

1

Analyze the expected behavior of a properly closed switch in a series circuit.

An ideal closed switch provides continuity with approximately

0\ \Omega

resistance and a voltage drop of nearly

0\text{ V}

.

According to Ohm's Law (

V = I \times R

), current flowing through near-zero resistance produces negligible voltage drop.

2

Evaluate the meter reading across the switch terminals.

The meter measures

12\text{ V}

, which equals the full source voltage.

In a series circuit, an open point has infinite resistance and drops the entire supply voltage because no current can flow through the rest of the circuit.

3

Determine the exact fault location based on the voltage drop.

Because the full

12\text{ V}

appears across the switch itself, the break in continuity is inside the switch.

If the lamp were open instead, the voltmeter across the intact closed switch would read

0\text{ V}

.

Anahtar Kavram

Voltage Drop Across Open vs. Closed Series Components

Tahmini Süre:1m 0s

Soru 955Soru →

In direct-current (DC) series circuit analysis, distinct electrical principles govern how current, voltage, resistance, and faults behave across a single closed pathway. Match each series circuit parameter or condition on the left with its correct governing rule on the right.

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Total equivalent resistance matches the direct sum of all individual resistive values; Circuit current matches remaining constant at every point; Total source voltage matches the sum of the individual voltage drops across all loads; An open-circuit fault matches immediately halting all current flow.

Series circuits are defined by a single pathway for current. Consequently, current (

I

) is identical at all points, total resistance (

R_T

) is the arithmetic sum of the component resistances, total voltage (

V_T

) equals the sum of the individual component voltage drops, and an interruption anywhere breaks the complete circuit, dropping total current to zero.

Adım Adım Çözüm

1

Identify the resistance relationship for series circuits.

Total resistance increases with each added resistor and is found by adding resistances directly (

R_T = R_1 + R_2 + \dots

).

Electrons must pass sequentially through every resistive element along the single pathway.

2

Determine the current distribution rule in a single-loop circuit.

Current magnitude is uniform everywhere (

I_T = I_1 = I_2

).

Charge cannot accumulate or branch off in an unbranched series loop.

3

Apply Kirchhoff's Voltage Law to the series loop.

Total applied voltage equals the sum of the series voltage drops (

V_T = V_1 + V_2 + \dots

).

The electrical potential energy supplied by the source must be completely dissipated across the series loads.

4

Evaluate the effect of an open-circuit fault.

An open condition creates infinite resistance, stopping all loop current (

I = 0\text{ A}

).

A continuous physical path is required for DC electron flow.

Anahtar Kavram

Fundamental series circuit characteristics: additive resistance, constant current, additive voltage drops (Kirchhoff's Voltage Law), and single-point failure dependency.

Tahmini Süre:1m 0s

Soru 956Soru →

In electronics manufacturing, materials are categorized by how easily they conduct electricity. Which of the following elements has four valence electrons in its outer shell and is widely used as a semiconductor?

Copper

Silicon

Rubber

Silver

Cevabı ve açıklamayı göster

Cevap: Silicon

Cevap

Silicon is the element with four valence electrons that functions as a semiconductor.

Silicon contains four valence electrons in its outer shell and exhibits electrical conductivity between that of a conductor and an insulator, making it the primary material for solid-state electronics like diodes and transistors.

Adım Adım Çözüm

1

Identify the defining atomic property of semiconductor materials.

Semiconductors possess four valence electrons in their outermost atomic shell (Group IV elements).

This atomic structure gives them an intermediate level of conductivity between conductors and insulators.

2

Evaluate the listed materials by their valence electron structure and electrical classification.

Silicon has four valence electrons (semiconductor), copper and silver have one valence electron (conductors), and rubber is a compound insulator.

Matching the criteria of four valence electrons identifies silicon as the correct semiconductor material.

Anahtar Kavram

Classification of materials by atomic valence structure into conductors (1-3 valence electrons), semiconductors (4 valence electrons), and insulators (5-8 valence electrons).

Tahmini Süre:45s

Soru 957Soru →

A secure military facility uses three independent detection systems to monitor its perimeter. The probability that the primary radar detects an incoming drone is 0.80. The probability that the infrared system detects it is 0.90. The probability that the acoustic sensors detect it is 0.75. If a drone approaches the perimeter, what is the probability that exactly two of the three systems detect it? Express your answer as a decimal.

Cevabı ve açıklamayı göster

Cevap: 0.375

Cevap

0.375

The correct answer is found by calculating the compound probability for each of the three specific scenarios where exactly two systems succeed and one fails, and then adding those mutually exclusive probabilities together.

Adım Adım Çözüm

1

Identify the mutually exclusive scenarios that result in exactly two systems detecting the drone.

Scenario 1: Radar and Infrared detect, Acoustic fails. Scenario 2: Radar and Acoustic detect, Infrared fails. Scenario 3: Infrared and Acoustic detect, Radar fails.

Because these three systems act independently, we must calculate the compound probability of each specific combination of two successes and one failure.

2

Calculate the probability of Scenario 1 (Radar and Infrared detect, Acoustic fails).

0.80 \times 0.90 \times (1 - 0.75) = 0.80 \times 0.90 \times 0.25 = 0.180

Multiply the probabilities of the two specific successful detections by the probability of the specific failure.

3

Calculate the probability of Scenario 2 (Radar and Acoustic detect, Infrared fails).

0.80 \times (1 - 0.90) \times 0.75 = 0.80 \times 0.10 \times 0.75 = 0.060

Multiply the probabilities of the two specific successful detections by the probability of the specific failure.

4

Calculate the probability of Scenario 3 (Infrared and Acoustic detect, Radar fails).

(1 - 0.80) \times 0.90 \times 0.75 = 0.20 \times 0.90 \times 0.75 = 0.135

Multiply the probabilities of the two specific successful detections by the probability of the specific failure.

5

Sum the probabilities of the three mutually exclusive scenarios.

0.180 + 0.060 + 0.135 = 0.375

To find the total probability of any of these mutually exclusive events occurring, add their individual joint probabilities together.

Anahtar Kavram

Calculating the probability of an exact number of successes among independent events by identifying all possible combinations of success and failure.

Tahmini Süre:2m 30s

Soru 958Soru →

A technician is inspecting a steady direct-current (DC) auxiliary circuit in a vehicle. Which of the following statements correctly describes the physical movement of electric charge carriers through the copper conductor?

Free electrons drift through the conductor away from the negative terminal and toward the positive terminal.

Positively charged atomic nuclei drift through the crystal lattice from the positive terminal toward the negative terminal.

Electromotive potential builds up statically across the wire without any physical displacement of particles.

Electrons rapidly alternate their direction of travel back and forth with no net forward displacement through the wire.

Cevabı ve açıklamayı göster

Cevap: Free electrons drift through the conductor away from the negative terminal and toward the positive terminal.

Cevap

Free electrons drift through the conductor away from the negative terminal and toward the positive terminal.

In solid metal conductors such as copper wiring, electric current is the physical flow of negatively charged free electrons. According to electrostatic principles, negative electrons are repelled by the negative terminal of the DC power source and attracted toward the positive terminal, establishing a continuous unidirectional drift.

Adım Adım Çözüm

1

Identify the mobile charge carriers in a solid metallic conductor.

In metals such as copper, loosely bound valence electrons are free to move, while positive atomic nuclei remain locked in the crystal lattice.

Determining which particles are mobile is the first step in analyzing physical current flow.

2

Determine the direction of electron drift under direct-current (DC) conditions.

Negatively charged electrons are repelled by the negative terminal and attracted toward the positive terminal, creating a continuous net directional drift.

Fundamental electrostatic laws dictate that opposite charges attract and like charges repel.

Anahtar Kavram

In metallic conductors carrying direct current, electric current is physically constituted by the net drift of negatively charged free electrons from the negative potential toward the positive potential.

Tahmini Süre:45s

Soru 959Soru →

An electronics technician connects an oscilloscope to test an alternating current circuit. The vertical scale (Volts/Div) is set to $5\text{ V/div}$ , and the displayed waveform has a total vertical span of $4\text{ divisions}$ from the highest peak to the lowest trough. What is the peak-to-peak voltage ( $V_{\text{p-p}}$ ) of the signal?

10\text{ V}

20\text{ V}

4\text{ V}

0.8\text{ V}

Cevabı ve açıklamayı göster

Cevap: $20\text{ V}$

Cevap

20\text{ V}

Peak-to-peak voltage (

V_{\text{p-p}}

) is the total voltage difference between the highest positive peak and the lowest negative trough of a waveform. Multiplying the total vertical displacement of

4\text{ divisions}

by the vertical sensitivity setting of

5\text{ V/div}

gives

4 \times 5 = 20\text{ V}

.

Adım Adım Çözüm

1

Identify the given vertical division count and the Volts/Div scale setting.

Vertical span =

4\text{ divisions}

; Vertical scale =

5\text{ V/div}

.

The vertical axis on an oscilloscope measures voltage according to the specified Volts/Div sensitivity.

2

Calculate the peak-to-peak voltage (

V_{\text{p-p}}

) by multiplying the total vertical divisions by the Volts/Div setting.

V_{\text{p-p}} = 4\text{ divisions} \times 5\text{ V/div} = 20\text{ V}

.

Each vertical grid square represents

5\text{ V}

, so

4

full squares equal

20\text{ V}

from minimum trough to maximum peak.

Anahtar Kavram

Calculating peak-to-peak voltage on an oscilloscope using graticule divisions and the Volts/Div scale setting

Tahmini Süre:45s

Soru 960Soru →

In electrical circuits, the power consumed or dissipated can be calculated using different formulas depending on which circuit parameters are known. Match each set of known circuit parameters on the left with the correct electrical power formula on the right. How should each parameter combination be paired with its corresponding power formula?

Soldaki öğeye tıklayın, sonra eşleşen sağdaki öğeye tıklayın

Cevabı ve açıklamayı göster

Cevap

Voltage and Current pairs with

P = V \times I

; Current and Resistance pairs with

P = I^2 R

; Voltage and Resistance pairs with

P = \frac{V^2}{R}

; Electrical Energy and Time pairs with

P = \frac{E}{t}

.

Each parameter combination matches its standard mathematical expression: Voltage and Current relate directly through Watt's Law (

P = V \times I

), Current and Resistance relate through

P = I^2 R

, Voltage and Resistance relate through

P = \frac{V^2}{R}

, and Energy and Time match the foundational definition of power (

P = \frac{E}{t}

).

Adım Adım Çözüm

1

Identify the base relationship of electrical power from fundamental physical definitions

Power is defined as energy divided by time:

P = \frac{E}{t}

.

This establishes the core definition of power in Joules per second (Watts).

2

Identify Watt's Law for circuits when potential difference and flow rate are known

Power is given by

P = V \times I

.

Multiplying potential difference (Volts) by current (Amperes) yields electrical power in Watts.

3

Use Ohm's Law substitutions to find power formulas for resistive circuits

When current and resistance are known:

P = I^2 R

. When voltage and resistance are known:

P = \frac{V^2}{R}

.

Substituting

V = IR

or

I = \frac{V}{R}

allows power to be determined when one electrical variable is omitted.

Anahtar Kavram

Electrical Power and Watt's Law Formulations

Tahmini Süre:45s

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Alternatif Yöntem

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm