Tüm alıştırma soruları

396 soru

Tüm türler5,215 Çoktan seçmeli2,665 Çoklu seçim6 Doğru / Yanlış260 Sayısal512 Eşleştirme930 Sıralama396 Boşluk doldurma397 Kısa cevap49

Soru 121Soru →

A carpenter is manually preparing rough-sawn hardwood stock to produce a flat, true, and finished face without power machinery. Place the following hand planes in the correct operational sequence, from the initial heavy stock reduction to final surface finishing.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct operational sequence begins with the scrub plane for bulk material removal, continues with the jack plane for intermediate leveling, proceeds to the jointer plane for trueing and straightening, and concludes with the smoothing plane for final surface polishing.

Bench hand woodworking planes are designed to work in a logical sequence governed by tool length and blade profile. The scrub plane removes bulk waste rapidly with its heavily radiused cutter; the jack plane removes coarse ridges and establishes primary dimensions; the jointer plane uses its extended sole to register across peaks and create true flatness; and the smoothing plane removes minute traces of previous passes to yield a pristine surface.

Adım Adım Çözüm

Traverse the rough lumber diagonally with a scrub plane.

Quick reduction of severe cupping, twist, and mill marks.

The scrub plane's radiused iron concentrates cutting pressure and clears thick shavings without binding.

Plane along the workpiece length using a jack plane.

Removal of deep scrub plane scallops and establishment of approximate thickness.

The intermediate bed length bridges rough furrows while continuing stock removal.

Pass the jointer plane across the entire face from end to end.

A true, planar reference surface free of bow or wind.

The 22- to 24-inch sole cannot fall into low areas, cutting exclusively on high spots until continuous full-length shavings are produced.

Make light, continuous passes along the grain with a finely tuned smoothing plane.

A glass-smooth, finish-ready wood face.

The closely set chipbreaker and minimal throat opening prevent tearout while removing thousandths of an inch.

Anahtar Kavram

Hand plane progression hierarchy based on sole length, iron camber, and cutting clearance from rough milling to final surface preparation.

Tahmini Süre:1m 30s

Soru 122Soru →

To ensure optimal performance and prevent internal damage, shop air supply systems use an FRL conditioning unit before the air reaches the pneumatic tool. Arrange the following components in the correct sequence of air flow, starting immediately from the main compressor drop line and ending at the tool connection.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence of air flow is: Particulate filter and water trap, followed by the Air pressure regulator, then the In-line tool lubricator, and finally the Quick-connect air hose coupling.

The standard FRL (Filter, Regulator, Lubricator) configuration is universally ordered to protect the system and the tool. The filter must intercept raw air first to strip out tank moisture and rust. The regulator follows to set the exact operating pressure using this clean air. The lubricator is positioned last in the conditioning unit so it can inject a fine oil mist into the clean, regulated air just before it travels through the hose coupling to lubricate the pneumatic tool's internal motor.

Adım Adım Çözüm

Identify the first required conditioning step for raw compressor air.

The particulate filter and water trap must be first.

Raw air contains condensation and tank rust. If not removed immediately, moisture will contaminate and ruin the downstream regulator and lubricator.

Determine the placement of the air pressure regulator.

The regulator is placed second in the sequence.

The regulator needs clean, dry air to function accurately without diaphragm damage, but it must control the pressure before oil is injected into the stream.

Determine the placement of the lubricator (oiler).

The lubricator is placed third.

Oil must be added to the clean, regulated air stream. If placed before the filter, the oil would be immediately stripped out. If placed before the regulator, it would clog the regulator valves.

Identify the final delivery point.

The quick-connect coupling is placed last.

The coupling connects the hose to deliver the fully prepared (clean, pressurized, and oiled) air directly to the pneumatic tool.

Anahtar Kavram

FRL (Filter, Regulator, Lubricator) Air Line Conditioning Sequence

Soru 123Soru →

An automotive technician is performing an industry-standard (USTMA/RMA) permanent one-piece patch-and-plug repair on a punctured tubeless radial passenger tire. In what sequential order should the technician execute the steps of this repair procedure?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

Dismount and inspect the inner liner → Ream the puncture channel → Buff the inner liner surface → Apply chemical vulcanizing cement → Install the patch-plug and stitch with a roller

The U.S. Tire Manufacturers Association (USTMA) and standard automotive service procedures mandate that any puncture repair must begin with dismounting the tire for internal inspection. Next, the injury channel is prepared by reaming out damaged steel cords. The inner liner must then be mechanically textured by low-speed buffing and coated with vulcanizing cement. Once the cement is dry, the combination patch-plug is installed from the inside and stitched with a roller to expel air.

Adım Adım Çözüm

Dismount the tire and perform an internal inspection.

Confirms the casing has not sustained hidden belt separation or run-flat sidewall powdering.

Industry safety standards prohibit external plug-only repairs because internal damage cannot be verified while mounted.

Probe and ream the injury channel.

Removes jagged wire fragments and aligns the injury path.

Preparing the puncture channel ensures the rubber stem can seal the tread area completely against water intrusion.

Scrape and buff the inner liner around the injury.

Produces a clean, textured surface free of mold release agents.

Chemical bonding requires raw, clean rubber; over-buffing into cord plies must be avoided.

Apply chemical vulcanizing cement and allow to dry.

Forms an active chemical bonding layer.

The cement must dry to a matte, non-glossy finish so solvents evaporate before applying the patch.

Pull the stem through from inside and stitch down the patch base.

Permanently seals both the tread channel (stem) and the inner liner airtight seal (patch).

Rolling from the center outward expels trapped air pockets, ensuring total surface adhesion.

Anahtar Kavram

Standard radial tire puncture repair requires a combination patch-and-plug unit applied from the inside out following strict preparation, buffing, cementing, and stitching stages.

Tahmini Süre:1m 15s

Soru 124Soru →

A mechanic is organizing a set of standard fractional (SAE) combination wrenches on a magnetic tool rail. In what order should the mechanic arrange the following wrench sizes from smallest opening size to largest opening size?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence from smallest to largest opening size is

5/16\text{ in}

3/8\text{ in}

7/16\text{ in}

, and

1/2\text{ in}

To order fractional SAE wrenches from smallest to largest, express each size with a common denominator of

16

5/16\text{ in}

3/8\text{ in} = 6/16\text{ in}

7/16\text{ in}

, and

1/2\text{ in} = 8/16\text{ in}

. Comparing the numerators yields the sequence

5/16\text{ in}

3/8\text{ in}

7/16\text{ in}

, and

1/2\text{ in}

Adım Adım Çözüm

Convert each fraction to a common denominator of 16

5/16\text{ in} = 5/16\text{ in}

3/8\text{ in} = 6/16\text{ in}

7/16\text{ in} = 7/16\text{ in}

, and

1/2\text{ in} = 8/16\text{ in}

Finding a common denominator allows direct comparison of fractional SAE wrench sizes.

Order the values by comparing their numerators

5/16 < 6/16 < 7/16 < 8/16

Since the denominators are identical, the size is directly proportional to the numerator.

List the original wrench sizes corresponding to the sorted order

5/16\text{ in} \rightarrow 3/8\text{ in} \rightarrow 7/16\text{ in} \rightarrow 1/2\text{ in}

Restores the wrench labels to their standard commercial SAE sizing format.

Anahtar Kavram

Fractional SAE Wrench Sizing and Comparison

Tahmini Süre:45s

Soru 125Soru →

A technician needs to set up a drill press to bore an accurate hole through a metal bracket safely. In what sequential order should the following preparatory and operational steps be performed from first to last?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The proper sequence begins with layout and center punching, followed by chucking the drill bit and removing the key, clamping the workpiece securely to the drill table, configuring the spindle speed, and finally powering on the machine to feed the quill.

The correct operational sequence follows standard machine shop safety and precision protocol: first, layout the hole center with a punch mark to guide the bit; second, install the bit and remove the chuck key; third, align and clamp the workpiece firmly to prevent lethal spinning; fourth, select the correct belt ratio/spindle speed for the bit diameter while the machine is off; and fifth, power on the motor and feed the quill smoothly.

Adım Adım Çözüm

Mark and center punch the hole location.

A clean indentation is formed at the exact drilling center.

Prevents the drill bit from skating or walking across the smooth metal surface upon initial contact.

Secure the drill bit in the chuck and remove the chuck key immediately.

The cutting tool is centered and clamped, and the hazard of a thrown chuck key is eliminated.

Leaving a chuck key in the chuck creates a lethal projectile hazard when the spindle turns.

Align the workpiece under the bit and clamp it firmly in a vise secured to the table.

The bracket cannot move, lift, or spin during drilling.

Eliminates dangerous rotational binding (the 'helicopter effect') when the drill bit bites into the metal.

Adjust the drive belt on the stepped pulleys to set the spindle RPM.

The drill press is configured for the optimal cutting speed for the given bit diameter and workpiece hardness.

Setting the speed must be done while the machine is stationary before initiating the cut.

Switch on the motor and apply steady feed pressure via the hand feed lever.

The hole is bored cleanly and safely through the bracket.

Executing the cut with steady feed produces proper chips and prevents tool overheating.

Anahtar Kavram

Standard drill press operational setup, safety protocols, and execution sequence

Tahmini Süre:1m 0s

Soru 126Soru →

An electronics technician needs to measure the direct current (DC) drawn by an indicator circuit operating on a $28\text{ V}$ DC bus using a digital multimeter (DMM). Place the following procedural steps in the correct chronological order to perform this measurement safely and accurately.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence begins with de-energizing the circuit, configuring the multimeter jacks and selector dial for DC current, opening a physical break in the circuit path, connecting the meter leads in series across the opening, and finally re-energizing the circuit to read the display.

Measuring electrical current requires the meter to become part of the conductive path (in series). Therefore, the correct procedure must start with safely de-energizing the circuit, configuring the multimeter's leads to the high-current (

10\text{ A}

) and common jacks with the dial set to DC current, opening a physical break in the circuit, connecting the probes across that break to complete the path in series, and lastly re-energizing the circuit to read the measured amperage.

Adım Adım Çözüm

De-energize the circuit power source.

Voltage and current flow are reduced to zero across all circuit components.

Safety protocol dictates that power must be disconnected before opening conductors to avoid electrical shock, short circuits, or component damage.

Configure the multimeter leads and selector switch.

The red lead is inserted into the fused

10\text{ A}

port, black in

\text{COM}

, and the dial is rotated to DC amperes (

\text{A}_{\text{DC}}

Setting the meter to the highest current range prior to measurement protects the internal current-sensing shunt and fuse from inrush current.

Open the conductor at the point of measurement.

A physical gap is created in the single conductive loop.

Current represents the rate of charge flow through a loop; the loop must be opened so the ammeter can become an integral link in that loop.

Attach the meter test probes in series across the gap.

The low-resistance internal ammeter circuit bridges the gap and completes the circuit path.

Connecting an ammeter in parallel across an active voltage source causes a catastrophic short circuit, whereas a series connection allows proper inline current sensing.

Reapply power and record the reading.

Current flows through the load and the meter, displaying the direct current value in amperes or milliamperes.

Current can only flow and be quantified when the circuit is actively powered.

Anahtar Kavram

Series Ammeter Insertion and Meter Configuration Protocol

Tahmini Süre:1m 0s

Soru 127Soru →

A technician is tracing the pathway of electrical energy in a conventional distributor-based ignition system. In what chronological sequence does electrical energy travel from the low-voltage source to ignite the cylinder's air-fuel mixture?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct chronological sequence is: (1) 12-volt battery current flows through the primary winding to build a magnetic field, (2) The primary circuit switch opens to collapse the magnetic field, (3) High voltage is induced in the secondary winding and travels to the distributor cap, and (4) The distributor rotor directs the high voltage across the spark plug wire to fire the spark plug.

In a conventional distributor ignition system, low-voltage current from the battery first energizes the primary coil windings to build a magnetic field. When the switching mechanism opens, the current stops and the magnetic field collapses instantly. This rapid collapse induces tens of thousands of volts in the secondary coil windings. The high-voltage surge enters the distributor cap, where the rotating rotor directs it to the correct spark plug wire, jumping the spark plug gap to ignite the compressed air-fuel mixture.

Adım Adım Çözüm

Identify the primary circuit energizing stage.

Low-voltage current from the battery flows through the primary coil winding, creating a strong magnetic field around the iron core.

An ignition coil must store electrical energy in a magnetic field before it can be stepped up to firing voltage.

Identify the triggering event that releases stored magnetic energy.

The contact points or switching transistor opens the circuit, abruptly interrupting primary current flow.

High-voltage induction requires a rapid rate of change in the magnetic lines of force.

Trace the step-up voltage transformation in the secondary circuit.

The collapsing magnetic lines cut through the secondary winding, inducing a surge of 20,000 to 50,000 volts that exits through the coil tower.

The high ratio of secondary turns to primary turns steps up the collapsing field energy into high voltage.

Trace the mechanical distribution to the combustion chamber.

The distributor rotor turns toward the cylinder's cap terminal, routing the surge through the plug wire to spark across the electrode gap.

The distributor mechanically times and directs the high voltage to the cylinder ready for combustion.

Anahtar Kavram

Ignition coil primary magnetic saturation, field collapse induction, and high-voltage distributor delivery

Tahmini Süre:1m 0s

Soru 128Soru →

When preparing to replace a cutting bit on a handheld wood router, what is the correct sequence of steps to safely perform this procedure?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

Disconnect the router from the electrical power supply, engage the spindle lock to hold the shaft, loosen the collet nut to remove the old bit, and then insert and firmly tighten the new bit shank.

The correct procedure begins by disconnecting the router from electrical power to ensure safety. Next, the spindle is held stationary with a spindle lock so that torque can be applied to loosen the collet nut. After the old bit is removed, the replacement bit shank is seated and firmly tightened in the collet before the router is ever reconnected to power.

Adım Adım Çözüm

Unplug the router from the electrical wall outlet.

The tool is completely de-energized.

Prevents accidental motor activation while fingers and wrenches are near the cutting assembly.

Depress the spindle lock pin or secure the arbor with a holding wrench.

The motor armature and spindle cannot rotate.

Allows rotational torque to be applied directly to the collet nut without the motor shaft spinning.

Turn the collet nut counterclockwise with a wrench to release the shank and remove the bit.

The collet releases its grip on the cutter.

Clears the chuck so the replacement bit can be seated.

Insert the new bit shank into the collet chuck and securely tighten the nut with the wrench.

The new bit is securely clamped and centered in the router.

Ensures the cutter cannot slip or fly out under high rotational speeds during operation.

Anahtar Kavram

Safe router bit replacement sequence

Tahmini Süre:45s

Soru 129Soru →

When performing a two-person manual bleeding procedure at an individual wheel brake assembly, what is the correct chronological sequence of steps to purge air from the hydraulic circuit?

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence begins with connecting the submerged drain tube, followed by pressurizing and holding the brake pedal, opening the bleeder screw to purge air, and finally tightening the bleeder screw before releasing the pedal.

Purging air from a hydraulic brake circuit requires positive pressure to expel air pockets and immediate sealing to prevent air ingestion. The technician first attaches a submerged hose, commands the assistant to pressurize the line, opens the bleeder valve to vent air and fluid, and tightens the valve before the pedal is released.

Adım Adım Çözüm

Connect the drain tube to the bleeder valve and submerge its tip in clean fluid.

Creates a sealed escape route for contaminated fluid and air.

Prevents air from being drawn backwards into the hydraulic circuit during the bleeding process.

Have an assistant depress and maintain steady pressure on the brake pedal.

Pressurizes the hydraulic fluid column from the master cylinder to the wheel unit.

Generates positive hydraulic pressure to drive trapped air pockets toward the exit port.

Loosen the bleeder screw one-quarter to one-half turn.

Pressurized fluid and air bubbles discharge through the transparent tube.

Expels trapped air out of the hydraulic cylinder or caliper bore.

Tighten the bleeder screw firmly before the assistant releases the pedal.

Reseals the hydraulic system under positive pressure.

Releasing the brake pedal creates low-pressure suction in the circuit; sealing the valve first prevents air from being sucked back inside.

Anahtar Kavram

Hydraulic brake bleeding sequence and positive pressure sealing

Tahmini Süre:1m 0s

Soru 130Soru →

A solid metal sphere is suspended from a digital spring scale and lowered completely into four different storage tanks, each containing a different liquid. The true weight of the sphere in the air remains constant.

The liquids and their approximate densities are:
- Gasoline: $0.75 \text{ g/cm}^3$
- Glycerin: $1.26 \text{ g/cm}^3$
- Freshwater: $1.00 \text{ g/cm}^3$
- Ocean water: $1.03 \text{ g/cm}^3$

Arrange the liquids in order based on the apparent weight shown on the spring scale when the sphere is completely submerged, from the GREATEST apparent weight to the LEAST apparent weight.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

Gasoline, Freshwater, Ocean water, Glycerin

The correct order follows the fluid densities from lowest to highest. A fluid with a lower density displaces less mass for a given volume, exerting a smaller upward buoyant force. Because Apparent Weight = True Weight - Buoyant Force, the smallest buoyant force results in the largest apparent weight. Therefore, gasoline (lowest density) yields the greatest apparent weight, and glycerin (highest density) yields the least apparent weight.

Adım Adım Çözüm

Identify the relationship between true weight, apparent weight, and buoyant force.

Apparent Weight = True Weight - Buoyant Force

A submerged object experiences an upward buoyant force that opposes gravity, reducing the measured weight on the scale.

Determine how the buoyant force relates to the different liquids.

Buoyant Force is directly proportional to the density of the liquid.

According to Archimedes' principle, buoyant force equals the weight of the displaced fluid. Since the same sphere is completely submerged every time, the displaced volume is constant, making buoyant force depend entirely on fluid density.

Correlate fluid density with apparent weight.

Lower fluid density produces a smaller buoyant force, resulting in a greater apparent weight.

Since apparent weight is calculated by subtracting the buoyant force from the constant true weight, subtracting a smaller value leaves a larger apparent weight.

Order the liquids from lowest density to highest density.

Gasoline (0.75), Freshwater (1.00), Ocean water (1.03), Glycerin (1.26).

This sequence represents the progression from the smallest buoyant force (greatest apparent weight) to the largest buoyant force (least apparent weight).

Anahtar Kavram

The apparent weight of a submerged object is its true weight minus the buoyant force. For a constant volume, a lower density fluid exerts a smaller buoyant force, resulting in a greater apparent weight.

Tahmini Süre:1m 0s

Soru 131Soru →

Arrange the following stages of a skydiver's descent from an aircraft to the ground in the correct chronological order.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence starts with initial downward acceleration, followed by increasing air resistance, reaching a constant terminal velocity, and finally parachute deployment to decelerate.

The sequence accurately describes the physical forces during an atmospheric free fall. Initially, gravity causes acceleration. As speed increases, so does opposing air resistance. Eventually, air resistance equals the gravitational force, resulting in a constant speed known as terminal velocity. Finally, deploying a parachute increases surface area, creating excess drag to rapidly decelerate the skydiver.

Adım Adım Çözüm

Identify the initial state of the fall.

The skydiver steps out and accelerates downward.

At the start of the fall, speed is very low, so gravity is the dominant force causing an initial downward acceleration.

Determine what happens as the skydiver's downward speed increases.

Upward air resistance grows.

Air resistance (drag) increases proportionally as the speed of the falling object moving through the atmosphere increases.

Identify the state where the forces eventually balance.

Air resistance balances gravity, leading to a constant speed.

This state is known as terminal velocity. The net force becomes zero, meaning acceleration stops and the skydiver falls at a steady rate.

Identify the final stage required before safely reaching the ground.

The parachute is deployed to slow the fall.

Deploying the parachute vastly increases the surface area, which temporarily makes air resistance much greater than gravity, safely decelerating the descent.

Anahtar Kavram

Gravity, Air Resistance, and Terminal Velocity

Soru 132Soru →

A logistics team is evaluating different ramp configurations to push heavy equipment into a warehouse. Calculate the ideal mechanical advantage (IMA) for each ramp. Order the following ramps from the GREATEST mechanical advantage (requires the least effort force) to the LEAST mechanical advantage (requires the most effort force).

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence from greatest to least mechanical advantage is: the 5m long / 1m high ramp, the 8m long / 2m high ramp, the 9m long / 3m high ramp, and finally the 4m long / 2m high ramp.

The correct order requires calculating the Ideal Mechanical Advantage (IMA = Length / Height) for each ramp and arranging them in descending order. The 5m/1m ramp has an IMA of 5. The 8m/2m ramp has an IMA of 4. The 9m/3m ramp has an IMA of 3. The 4m/2m ramp has an IMA of 2.

Adım Adım Çözüm

Recall the formula for the Ideal Mechanical Advantage (IMA) of an inclined plane.

IMA = Length of the incline ÷ Vertical height (IMA = L / h).

This formula determines how much the ramp multiplies the applied force.

Calculate the IMA for the ramp with a length of 5 meters and a height of 1 meter.

IMA = 5 ÷ 1 = 5.

Direct application of the IMA formula.

Calculate the IMA for the ramp with a length of 8 meters and a height of 2 meters.

IMA = 8 ÷ 2 = 4.

Direct application of the IMA formula.

Calculate the IMA for the ramp with a length of 9 meters and a height of 3 meters.

IMA = 9 ÷ 3 = 3.

Direct application of the IMA formula.

Calculate the IMA for the ramp with a length of 4 meters and a height of 2 meters.

IMA = 4 ÷ 2 = 2.

Direct application of the IMA formula.

Order the calculated IMA values from greatest to least.

5, then 4, then 3, then 2.

The question asks for the order from greatest mechanical advantage to least.

Anahtar Kavram

The ideal mechanical advantage of an inclined plane is calculated by dividing the length of the incline by the vertical height (IMA = L / h). A greater IMA means less effort force is required to move an object up the ramp.

Tahmini Süre:1m 0s

Soru 133Soru →

Arrange the following stages of a skydiver's jump in chronological order, starting from the moment they step out of a hovering helicopter until just before they touch the ground.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence follows the progression of forces: maximum initial acceleration, decreasing acceleration as drag builds, first terminal velocity, rapid deceleration upon parachute deployment, and finally a second, slower terminal velocity.

A falling object initially accelerates under gravity alone. As its velocity increases, air resistance grows until it perfectly opposes gravity, resulting in a constant terminal velocity. Deploying a parachute drastically increases the surface area, creating a temporary net upward force that slows the fall until a new, slower terminal velocity is established for a safe landing.

Adım Adım Çözüm

Analyze the initial phase of the jump.

Identify that at the moment of the jump, velocity is zero.

Without velocity, there is no air resistance. Gravity is the only force, causing maximum acceleration.

Evaluate the effect of increasing speed.

Determine that accelerating downwards causes air resistance to grow.

Air drag is proportional to velocity. As drag increases, it opposes gravity, reducing the net downward acceleration.

Identify the first equilibrium state.

Recognize that terminal velocity is reached when air resistance equals gravity.

When the net force is zero, Newton's first law dictates that acceleration stops and velocity becomes constant.

Assess the impact of parachute deployment.

Identify that the parachute causes a massive, sudden increase in air drag.

The drag force temporarily exceeds the gravitational force, creating an upward net force that rapidly slows the downward fall.

Determine the final state before landing.

Conclude that a new equilibrium is reached at a much slower speed.

As the skydiver slows down, the drag on the parachute decreases until it balances gravity once more.

Anahtar Kavram

The relationship between gravity, air resistance, and terminal velocity during free fall.

Soru 134Soru →

A mechanic has four different bolts. Arrange the bolts in order from the LEAST linear distance traveled per full revolution to the GREATEST linear distance traveled per full revolution.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct order from least to greatest linear travel is: 32 TPI, 20 TPI, 16 TPI, and 10 TPI.

The linear distance a screw travels in one full revolution is its pitch, which is calculated as 1 divided by the Threads Per Inch (TPI). A higher TPI means the threads are closer together, so the screw advances a shorter distance per turn. Therefore, to order them from least to greatest distance traveled, you must arrange them from highest TPI to lowest TPI: 32 TPI (1/32 inch), 20 TPI (1/20 inch), 16 TPI (1/16 inch), and 10 TPI (1/10 inch).

Adım Adım Çözüm

Understand the relationship between threads per inch (TPI) and linear travel.

Linear travel per revolution, also known as pitch, is equal to 1 divided by the TPI.

Each full turn advances the screw by one thread pitch.

Determine the linear travel for each bolt.

32 TPI = 1/32 inch, 20 TPI = 1/20 inch, 16 TPI = 1/16 inch, and 10 TPI = 1/10 inch.

Applying the relationship pitch = 1 / TPI.

Order the calculated values from least to greatest.

1/32 < 1/20 < 1/16 < 1/10.

The question asks for the order starting with the least linear distance traveled.

Anahtar Kavram

The linear distance a screw travels in one revolution is its pitch. For standard screws, pitch is the reciprocal of the threads per inch (TPI). Therefore, a higher TPI results in a smaller linear travel per revolution.

Tahmini Süre:45s

Soru 135Soru →

A woodworker is selecting a replacement spindle for a workbench vise. They have four options with identical handle lengths and spindle diameters. Arrange the vise spindles in order from the one that applies the MAXIMUM clamping force for a given amount of effort, to the one that applies the MINIMUM clamping force.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence is: 12 TPI, 8 TPI, 5 TPI, and 3 TPI.

The mechanical advantage of a screw determines how much clamping force is produced from a given effort force. It is inversely proportional to its pitch (the linear distance between adjacent threads). Threads per inch (TPI) is the inverse of pitch, meaning a higher TPI results in a smaller pitch. A smaller pitch creates a shallower thread angle, which maximizes the mechanical advantage and produces the greatest clamping force. Therefore, the spindle with 12 TPI applies the maximum force, while the one with 3 TPI applies the minimum force.

Adım Adım Çözüm

Identify the relationship between Threads Per Inch (TPI) and pitch.

Pitch is the inverse of TPI. A higher TPI translates to a smaller pitch (distance between threads).

Understanding pitch is necessary to determine the mechanical advantage of the screw.

Relate pitch to mechanical advantage and clamping force.

A smaller pitch means the screw advances less linear distance per revolution, acting like a shallower inclined plane. This increases mechanical advantage, resulting in greater output clamping force for the same effort.

The question asks to order the spindles by the amount of clamping force applied.

Rank the spindles from maximum to minimum clamping force.

Maximum clamping force corresponds to the highest TPI. The correct order is 12 TPI, 8 TPI, 5 TPI, and 3 TPI.

This establishes the final required arrangement.

Anahtar Kavram

Mechanical Advantage of Screws Based on TPI

Soru 136Soru →

Calculate the total effort force required for each scenario and arrange the following inclined plane configurations in order from the GREATEST required effort force to the LEAST required effort force.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence from greatest to least effort force is: 240 lb crate (90 lb effort), 160 lb crate (80 lb effort), 300 lb crate (75 lb effort), and 450 lb crate (70 lb effort).

The total effort force required is the sum of the ideal effort (weight divided by IMA) and the friction force. For the 240 lb crate, the total effort is 90 lb. For the 160 lb crate, it is 80 lb. For the 300 lb crate, it is 75 lb. For the 450 lb crate, it is 70 lb. Arranging these from greatest to least yields the sequence of 90 lb, 80 lb, 75 lb, and 70 lb.

Adım Adım Çözüm

Calculate the Ideal Mechanical Advantage (IMA) for each ramp.

Item 1: 5. Item 2: 2. Item 3: 10. Item 4: 4.

IMA is determined by the ratio of the ramp's length to its vertical height (

IMA = \frac{L}{h}

Determine the ideal effort force required to move each load without friction.

Item 1: 60 lb. Item 2: 80 lb. Item 3: 45 lb. Item 4: 60 lb.

The ideal effort force is the weight of the load divided by the IMA (

F_{\text{ideal}} = \frac{W}{IMA}

Add the constant friction force to the ideal effort force to find the total required effort.

Item 1: 75 lb. Item 2: 80 lb. Item 3: 70 lb. Item 4: 90 lb.

Friction acts against the movement up the ramp, so it must be added to the ideal effort force to find the true required effort.

Arrange the final total effort values in descending order.

90 lb, 80 lb, 75 lb, 70 lb.

The question asks for the order from greatest required effort force to least.

Anahtar Kavram

Calculating total required effort force on an inclined plane by combining Ideal Mechanical Advantage (IMA) and frictional forces.

Soru 137Soru →

A skydiver jumps from a stationary hot air balloon. Arrange the following moments of the jump in order of the skydiver's acceleration, starting from the greatest downward acceleration and ending with the greatest upward acceleration.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence tracks the decreasing downward acceleration: immediately after jumping (maximum downward), followed by several seconds into the fall (reduced downward), then falling at terminal velocity (zero acceleration), and finally the moment the parachute inflates (strong upward acceleration).

The correct sequence tracks the net force acting on the skydiver. Initially, only gravity acts, causing maximum downward acceleration. As speed increases, upward air drag grows, reducing the net downward force and acceleration. At terminal velocity, drag equals weight, making net force and acceleration zero. When the parachute opens, drag vastly exceeds weight, creating a net upward force and thus an upward acceleration.

Adım Adım Çözüm

Analyze the forces acting immediately after the jump.

Velocity is zero, so air drag is zero. The only force is gravity, resulting in the maximum downward acceleration of approximately 9.8 m/s².

Air drag depends on velocity. Without velocity, there is no drag to oppose gravity.

Evaluate the forces during the middle of the fall before terminal velocity.

As the skydiver speeds up, upward air drag increases. The net downward force becomes less than gravity, so downward acceleration is less than 9.8 m/s².

Net force equals weight minus air drag. As drag increases, net force decreases, reducing acceleration according to Newton's Second Law.

Identify the conditions at terminal velocity.

Upward air drag exactly equals downward weight. The net force is zero, meaning acceleration is exactly 0 m/s².

Terminal velocity is reached when opposing forces balance out completely, ending any change in speed.

Assess the moment the parachute inflates.

The huge surface area creates an upward air drag much greater than the downward weight. The net force points upward, creating a strong upward acceleration.

A net upward force is required to rapidly decrease the downward velocity to a safe landing speed.

Anahtar Kavram

The relationship between gravity, air resistance, and net acceleration during free fall through an atmosphere.

Soru 138Soru →

A construction team uses various temporary ramps to roll heavy equipment platforms to different elevated levels. Assuming friction is negligible, arrange the following ramp configurations in order from the LEAST effort force required to the GREATEST effort force required.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct order from least effort force to greatest effort force is: the 25 ft ramp, followed by the 20 ft ramp, then the 18 ft ramp, and finally the 14 ft ramp.

The effort force required to move an object up a frictionless inclined plane is determined by the ratio of the height to the length of the plane. A lower height-to-length ratio means a higher mechanical advantage and less required effort force. By calculating this ratio for each ramp, we find the 25 ft ramp requires

\frac{1}{5}

(20%) of the load's weight, the 20 ft ramp requires

\frac{1}{4}

(25%), the 18 ft ramp requires

\frac{1}{3}

(33.3%), and the 14 ft ramp requires

\frac{1}{2}

(50%). Therefore, the sequence is 25 ft ramp, 20 ft ramp, 18 ft ramp, and 14 ft ramp.

Adım Adım Çözüm

Identify the relationship between effort force, load, ramp length, and height.

\text{Effort Force} = \text{Load} \times \left(\frac{\text{height}}{\text{length}}\right)

The effort force is inversely proportional to the ideal mechanical advantage (

\text{IMA} = \frac{\text{length}}{\text{height}}

Calculate the effort force fraction for each ramp configuration.

25 ft ramp:

\frac{5}{25} = \frac{1}{5}

; 20 ft ramp:

\frac{5}{20} = \frac{1}{4}

; 18 ft ramp:

\frac{6}{18} = \frac{1}{3}

; 14 ft ramp:

\frac{7}{14} = \frac{1}{2}

Comparing these fractions allows us to determine the relative force required for an identical load.

Order the calculated fractions from lowest to highest.

\frac{1}{5} < \frac{1}{4} < \frac{1}{3} < \frac{1}{2}

The prompt asks to arrange the setups from the least effort force to the greatest effort force.

Anahtar Kavram

Ideal Mechanical Advantage and Effort Force on an Inclined Plane

Soru 139Soru →

Rank the following inclined plane configurations in order from the LEAST effort force required to the GREATEST effort force required. Assume ideal conditions with no friction.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct sequence from least to greatest effort force is: the 500 lb load on a 15 ft ramp (100 lbs), followed by the 600 lb load on a 12 ft ramp (150 lbs), then the 400 lb load on an 8 ft ramp (200 lbs), and finally the 750 lb load on a 15 ft ramp (250 lbs).

The effort force required for an inclined plane is calculated by dividing the weight of the load by the Ideal Mechanical Advantage (IMA = Length / Height). Calculating this for each scenario yields: 100 lbs, 150 lbs, 200 lbs, and 250 lbs respectively. Organizing these from least to greatest provides the correct sequence.

Adım Adım Çözüm

Calculate the effort force for the

750\text{ lb}

cargo.

Force =

750 \times (5 / 15) = 750 \times (1 / 3) = 250\text{ lbs}

To determine the actual force needed, divide the load by the Ideal Mechanical Advantage (IMA = Length / Height).

Calculate the effort force for the

400\text{ lb}

cargo.

Force =

400 \times (4 / 8) = 400 \times 0.5 = 200\text{ lbs}

The ramp's IMA is 2, meaning it halves the required lifting force.

Calculate the effort force for the

600\text{ lb}

cargo.

Force =

600 \times (3 / 12) = 600 \times 0.25 = 150\text{ lbs}

The ramp has an IMA of 4, which divides the

600\text{ lb}

load by 4.

Calculate the effort force for the

500\text{ lb}

cargo.

Force =

500 \times (3 / 15) = 500 \times 0.2 = 100\text{ lbs}

This configuration provides an IMA of 5, which significantly reduces the force.

Order the calculated effort forces from least to greatest.

The correct order is

100\text{ lbs}

150\text{ lbs}

200\text{ lbs}

250\text{ lbs}

The question specifically requests the sequence from least effort to greatest effort.

Anahtar Kavram

Ideal Mechanical Advantage and Effort Force in Inclined Planes

Tahmini Süre:2m 0s

Soru 140Soru →

Rank the following jackscrew configurations in order from the highest Ideal Mechanical Advantage (IMA) to the lowest IMA.

Öğeleri doğru sıraya koymak için sürükleyin

Cevabı ve açıklamayı göster

Cevap

The correct order from highest to lowest Ideal Mechanical Advantage is: the 8-inch handle with 8 TPI, followed by the 10-inch handle with 6 TPI, then the 12-inch handle with 4 TPI, and finally the 15-inch handle with 3 TPI.

The Ideal Mechanical Advantage of a jackscrew is determined by multiplying the circumference of the effort circle (

2 \times \pi \times L

) by the Threads Per Inch (TPI). Because

2\pi

is constant for all options, we can simply compare the product of the handle length (

L

) and the TPI. The 8-inch/8 TPI setup yields the highest proportional factor (

8 \times 8 = 64

), followed by the 10-inch/6 TPI setup (

60

), the 12-inch/4 TPI setup (

48

), and finally the 15-inch/3 TPI setup (

45

Adım Adım Çözüm

Identify the formula for the Ideal Mechanical Advantage (IMA) of a jackscrew.

IMA = (2 × π × Handle Length) / Pitch. Since Pitch = 1 / TPI, this simplifies to IMA = 2 × π × Handle Length × TPI.

To find the relative IMA, we need to compare the product of the handle length and TPI for each configuration.

Calculate the proportional IMA factor (Handle Length × TPI) for each jackscrew configuration.

8-inch handle, 8 TPI: 8 × 8 = 64. 10-inch handle, 6 TPI: 10 × 6 = 60. 12-inch handle, 4 TPI: 12 × 4 = 48. 15-inch handle, 3 TPI: 15 × 3 = 45.

This provides a comparative numerical value to rank the mechanical advantages without needing to calculate the exact factor of 2π.

Order the configurations based on the calculated factors.

64 > 60 > 48 > 45.

The prompt requests ranking from the highest IMA to the lowest IMA.

Anahtar Kavram

Ideal Mechanical Advantage of a Screw

ÖncekiSayfa 7 / 20Sonraki

Tüm alıştırma soruları

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram

Sık Yapılan Hatalar

Cevap

Adım Adım Çözüm

Anahtar Kavram